Arec DS-MT1 User manual

DS-MT1
HDMI 2.0 over IP
Multicast Transceiver System
User Manual English
AREC Inc.© All Rights Reserved 2023. l www.arec.com
All information contained in this document is Proprietary

DS-MT1 User Manual
1
The DS-MT1 HDMI 2.0 over IP Multicast Transceiver System with Bi-directional IR, RS-232, Audio
Extender/Extractor, USB & Video Wall Support boosts up your video/audio transmission distance up
to 100m(330ft)**[over copper] or 300m (990ft) (OM3) / 400m (1320ft) (OM4)[over fiber] in Ultra-HD
4K2K@60(4:4:4) format. Users can readily extend Ultra-HD sources from Blu-ray Disc player, PS4, PC, and
any other HDMI sources to distant display / monitor, including HDMI or DVI enabled TV sets or LCD PC
monitors. Besides DS-MT1 is HDCP compliant.
With broadcasting management software and 10 Gigabit Ethernet network switch (supported IGMP
Snooping), DS-MT1 is a complete Ultra-HD 4K2K@60(4:4:4) video broadcasting solution for many
4K requirement applications, such as medical care, digital signage etc. It can transmit Ultra-HD
4K2K@60(4:4:4) HDMI video broadcasting over IP network. The broadcasting format can be Point to Point,
Point to Many, and Multi-Casting. Multi-casting is based on Managed 10 Gigabit Switch with 802.1Q
VLAN function which provides control remotely with multi device.
INTRODUCTION
INTRODUCTION
FEATURES
PACKAGE CONTENTS
CONNECTION DIAGRAM
SPECIFICATIONS
PANEL DESCRIPTIONS
IR PASS-THROUGH
HDMI PIN DEFINITION
OPERATION APPROACH
WARRANTY
1
2
2
3
4
4
5
14
15
16
Table of Contents
* Up to 4K@60 4:4:4 (4K@60 4:4:4 needs light compression)
** Cat-6A cable or better is recommended for better performance

DS-MT1 User Manual
2
▪ Supports HDR and up to 4K@60 4:4:4
▪ HDCP & CEC Bypass
▪ Supports EDID management
▪ Can be configured as a full duplex transmitter and receiver when 4K@60 4:4:4
▪ Slide switch to select transmission over 10G copper RJ45 or SFP
▪ Auto equalization
▪ Pure unaltered uncompressed 7.1ch digital HDMI over cat.6A/fiber transmission
▪ DTS-HD Master Audio and Dolby TrueHD high bit rate audio support
▪ Supports bi-directional full frequency IR signal from 20KHz to 60KHz
▪ Bi-directional Analog audio path-through
▪ Full duplex RS-232 control up to 115,200 bps
▪ Cat.6A/fiber extension and connection to a 10GbE Ethernet Switch which support IGMP version 2.
▪ Supports software to configure & upgrade device and to control the switching operation of the
various signal types
▪ Supports seamless switching
▪ Supports Video Wall* & Multi-view function
▪ Supports custom scaling to display
FEATURES
* Supports the compensation of frame-tearing
** Cat-6A cable or better is recommended for better performance
▪ 1x DS-MT1
▪ 1x IR blaster
▪ 1x IR receiver
▪ 1x DC 12V
▪ 1x User Manual
PACKAGE CONTENTS

DS-MT1 User Manual
3
CONNECTION DIAGRAM
TX
RX
Laptop
Blue-ray
Display Display
HDMI Cable HDMI Cable
Gigabit Ethernet Switch
API server
HDMI Cable
Outgoing IR
Signal Outgoing IR Signal
Incoming IR
Signal Incoming IR Signal
HDMI Cable
SDVoE network switch capability requirements
· 10 gigabit connectivity (one port per endpoint)
· IGMP version 2 support
SDVoE network switch conguration requirements
· IGMPv2 Snooping: Enabled
· IGMP Fast Leave: Enabled
· Unregistered Multicast Flooding: Disabled

DS-MT1 User Manual
4
Technical
Role of usage Transceiver
HDMI compliance HDMI 2.0a
HDCP compliance HDCP 2.2 & 1.4
Video bandwidth Single-link 594MHz [18Gbps]
Video support 480i / 480p / 720p / 1080i / 1080p60 / 4K2K@30 / 4K2K@60 4:4:4
HDMI over UTP 4K2K@60 4:4:4 100m (330ft) [CAT.6A]
HDMI over ber 4K2K@60 4:4:4 up to 300m (990ft) (OM3) / 400m (1320ft) (OM4)
Audio support [multi-mode optic cable]
Equalization Surround sound [up to 7.1ch) or stereo digital audio
Input TMDS signal Auto
Input DDC signal 1.2 Volts [peak-to-peak]
ESD protection 5 Volts [peak-to-peak, TTL]
PCB stack-up Human body model — ±15kV [air-gap discharge] & ±8kV [contact discharge]
IR pass-thru 6-layer board [impedance control — differential 100Ω; single 50Ω]
RS-232 support Bi-directional
I/O connector Yes
HDMI source control 2x HDMI + 4x 3.5mm + 3x USB + 2x RJ45 + 1x ber + 1x RS-232
HDMI connector Controllable via IR pass-through from RX to TX or TX to RX with IR extenders
RJ-45 connector Type A [19-pin female]
USB connector WE/SS 8P8C
3.5mm connector Type A
Mechanical
Housing Metal enclosure
Dimensions [ L x W x H ]
Model : 172 x 162 x 30mm [6.7" x6.3" x1.2"]
Package : 325 x 196 x 92mm [12.7" x 7.7" x 3.6"]
Carton : 490 x 426 x 352mm [1'6" x 1'4" x 1'2"]
Weight Model : 685g[1.5 lbs] / Package : 400g [3 lbs]
Fixedness Wall-mounting case with screws
Power supply 12V DC
Power consumption 18 Watt [max]
Operation temperature 0~40°C [32~104°F]
Storage temperature -20~60°C [-4~140°F]
Relative humidity 20~90% RH [no condensation]
SPECIFICATIONS

DS-MT1 User Manual
5
PANEL DESCRIPTIONS
1. USB-HID : Connect to keyboard or mouse
2. USB-HID :
[ Top USB ] Connect to keyboard or mouse [Bottom USB]
(1) Connector to keyboard or mouse when the USB routing on the software is set as "remote"
(2) Connect to computer when the USB routing on the software is set as "local"
3. Indicator LED : USB-HID LED
4. 10G Copper IN/OUT : Plug in RJ-45 cable that needs to be linked to the other unit
5. Indicator LED : Link LED
6. 10G SFP IN/OUT* :
Plug in single/multi-mode ber optic cables cable that needs to be linked to the other unit
( * Fiber module is NOT included in the product )
7. Ethernet Port : Ethernet control port
8. Dip Switch :
DIP Switch Position Description
PIN#1 PIN#2
ON [ ↓] OFF [ ↑] FW update 1
ON [ ↓] ON [ ↓] Reserved
OFF [ ↑] ON [ ↓] FW update 2
OFF [ ↑] OFF [ ↑] Normal mode
PIN#3 ON [ ↓] Select transmission over SFP
OFF [ ↑] Select transmission over copper
1 3 4 5 6 7 8
2

DS-MT1 User Manual
6
9. +12V DC : Connect to a 12V power supply unit
10. Indicator LED : Power LED
11. IR Receiver : Infrared 3.5mm socket for plugging in the extension cable of IR receiver
12. IR Blaster : Infrared 3.5mm socket for plugging in the extension cable of IR blaster
13. Micro-USB : for F/W update
14. RS-232( terminal block format ) :
The order of RS-232 pin are TX, RX, GND ( from the left side to the right )
15. Stereo OUT : Connect to analog stereo audio speaker
16. Stereo IN : Connect to analog stereo audio source
17. Indicator LED : HDMI out signal LED
18. Indicator LED : HDMI in signal LED
19. HDMI OUT : Connect to a HDMI display with a HDMI male-male cable
20. HDMI IN : Connect to a HDMI source with a HDMI male-male cable
10 13 14 15 16 19 20
9 11 12 17 18

DS-MT1 User Manual
7
IR PASS-THROUGH
Users can create video streams on the streaming service platform. The below steps show how to
complete the video streaming settings from Twitch and YouTube.
IR BLASTER : plug in the IR blaster to emit all IR command signals received from the IR receiver from the
other end to control the devices corresponding to the IR signals.
IR RECEIVER : plug in the IR receiver to receive all IR command signals from the IR remote controls of the
corresponding devices.
IR Blaster IR Receiver
[ IR Extenders ]
[ IR Sockets ]
[ Denition of IR Earphone Jack ]
Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before
plugging in the IR extender to the respective IR sockets. Warranty will not cover the damage.
You can buy any IR extension cables in the market that are compatible to the denition of the IR sockets for the extender if
necessary for replacement use. However, IR cables longer than 2m (6-ft) may not work.

DS-MT1 User Manual
8
HDMI PIN DEFINITION
Pin 1 TMDS Data2+
Pin 2 TMDS Data2 Shield
Pin 3 TMDS Data2–
Pin 4 TMDS Data1+
Pin 5 TMDS Data1 Shield
Pin 6 TMDS Data1–
Pin 7 TMDS Data0+
Pin 8 TMDS Data0 Shield
Pin 9 TMDS Data0–
Pin 10 TMDS Clock+
Pin 11 TMDS Clock Shield
Pin 12 TMDS Clock–
Pin 13 CEC
Pin 14 Reserved (N.C. on device)
Pin 15 SCL
Pin 16 SDA
Pin 17 DDC/CEC Ground
Pin 18 +5V Power
Pin 19 Hot Plug Detect
Type A (Receptacle) HDMI

DS-MT1 User Manual
9
* The control server listens at port 22280 by default. Please make sure that this port is not occupied or change the client port.
OPERATION APPROACH
1. System Requirement
(1) OS information: Microsoft Windows 7/10/11
(2) Software size: 35MB
(3) Minimum RAM requirement: 256MB
2. Start the software control program
(1) Extract the SDVoE Controller vX.X.rar le.
(2) Run SDVoE Controller.exe le from the folder.
(3) The application will automatically deploy the necessary les at the rst start.
(4) It's ready to be used once the controlserver.exe and the SDVoE Controller.exe are both running.
Software Control through Ethernet port