ARG Dynamo User manual

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
THE NEW CONCEPT OF AEROBATIC TRAINER JET
FULL ITALY MADE
INSTRUCTION MANUAL
Version 3.3

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
DYNAMO SPORT JET by ARG S.a.s.
The Dynamo is designed and built entirely by ARG Sas, with the aim of providing customers with an aerobatic trainer
model that encloses all the characteristics of a sport Jet to begin flight operations with the turbine propulsion.
The special attention paid to the choice of profiles and fiber construction, made it possible to obtain a model with a low
wing loading, just 170 gr/dm2, that allows a takeoff from asphalt and from grass after only 30 meters and a really low
speed during the landing with a very small turbine of 80Nw
Due to the accurate internal engineering made it possible to obtain a fast and easy model to assembly even for those
who have no experience in building models with turbine propulsion.
The Dynamo is the perfect choice to become part of the wonderful world of the Rc-Jet with a model built entirely in
Italy to guarantee an high quality.
Technical Characteristics
Wing Span : 1.999 mm
Wing Span with Winglets ( optional ) : 2340 mm.
Lenght : 2.180 mm.
Weight : 550 mm. with landing gear closed
Wing Area : 56,1 dm2 ( without winglets ) –63,3 dm2 ( with winglets )
Empty weight : 9,3 Kg.
Weight : 10,8 Kg include di 1,98 lt of kerosene
Wing Loading : 170 Gr/dm2 ( with winglets)
Suggested Turbine : Min 60 N –Max 100 N
Speed range : from 30 Km/h to max 250 Km/h

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
KIT CONTENTS
- GFK PARTS / AIREX / CARBON
No. 1 GFK fuselage complete of internal parts
No. 1 Right wing short version (long wing version on demand)
No. 1 Right wing short version (long wing version on demand)
No. 1 Right stabilizer
No. 1 Left stabilizer
No. 1 Canopy
No. 1 Turbine cover
No. 1 Main wheel cover
- ACCESSORIES INCLUDED
POS
Q.TY
Description
1
1
Main tank support
2
1
Second turbine support
3
1
Electronic Front plate
4
1
Electronic rear plate
5
1
Support electronic plate
6
1
Centrale support plate
7
1
Front wheel mudguard
8
1
Short Wing Tips
9
2
Girders supporting turbine S = 10 mm
10
1
Reduction plate for 2.5 liters tank
11
1
Main Aluminium joiner Ø = 25x22 mm L = 907 mm .
12
1
Aluminium Elevator joiner Ø 10x8 = L = 210 mm .
13
1
Aluminum Flame Sp = 0.5 mm .
14
1
Complete tank 1600 ml . / 2500 ml ( Optional)
15
1
Complete tank 380 ml - UAT
16
1
Lock plate for main tank
17
3
Aileron and rudder servo cover 65 x 65 mm
18
2
Stabilizer servo cover 48 x 54 mm .
19
3
Servo mount for aileron and rudder ( Servo Graupner DES 806 BBMG )
20
2
Servo mount for elevator ( servo Graupner DS3288 BBMG )
21
10
Control horns moving parts
22
4
Control Horns for Flaps
23
1
Template for opening nosewheel
24
13
Kit for fixing Flame protection
25
1
Template for cutting port aileron servos - Directional Graupner
26
1
Template for cutting port elevator servos Graupner
27
8
Nuts MA for pushrod lock
28
6
Allen screw MA 3x15 mm for tank plate and electronic plate
29
2
Allen Screw MA 5x25 mm for fixing wings
30
2
MA jaw nut for mounting wings
31
2
Self-tapping screws Ø 2,2 x 16 mm for Locking the stabilizer
32
1
Allen screw MA 3x25 for fixing Canopy
33
7
MA blind nut for fixing Canopy - Tank - Electronics
34
39
Self-tapping screws ø 2,2 x 10 mm cop . servo- turbine - tank reduction plate - flame protection
35
2
20X18 Steel Washer Ø 6 mm hole .

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
36
4
MA jaw nut for fixing turbine
37
4
Allen screw MA 4x20 mm to fix the turbine
38
8
Fork Metal M3
39
1
Push rod L = 80 mm. X directional
40
2
Push rod L = 50 mm. X ailerons
41
5
Push rod L = 40 mm. X flaps and nosewheel
42
8
Ball links M3 - RED complete with screws and nuts
43
1
Tygon Tube 1/8
44
1
Fuel Clunk anti-bubbles for UAT
45
1
Fuel Clunk for main tank
SUGGESTED ACCESSORIES TO FINISH THE MODEL
POS
Q.TY
PRODUCT CODE
DESCRIPTION
SUPPLIER
50
1
ER40WS
ER40Evo- 3 Gear. With steering system
INTAIRCO
51
2
INTMA76
Main wheels Intairco 76mm with e-brake
INTAIRCO
52
2
Damp legs L = 150 mm.
INTAIRCO
53
1
Damp legs L = 190 mm.
INTAIRCO
54
1
INTNO 76
Nose wheel Intairco 76mm
INTAIRCO
55
6
DES 806 BBMG
Servo GRAUPNER DES 806 BBMG
GRAUPNER
56
2
DS3288 BBMG
Servo GRAUPNER DS3288 BBMG
GRAUPNER
57
1
VT80
Turbojet engine VT80
JETS MUNT
58
1
M100X
Merlin 100X Engine
JETS MUNT
59
1
AW-90010405
PowerBox Alewings miniMAC2 Li-Poli Adjust
ALEWINGS
60
1
Fuselage bags
ARG
61
1
Wing, rudder, stabilizer bags
ARG
62
1
Complete wire kit
ALEWINGS
63
1
Tx-Rx Grapner MX20
GRAUPNER
64
1
FMC-MACHPRO35-2200-2S
Lipo MACHPRO 2200 - 2S - 35C Turbine
ARG
65
2
FMC-MACHPRO35-2200-2S
Lipo MACHPRO 2200 - 2S - 35C Elettronic
ARG
66
1
FMC-MACHPRO25-1350-2S
Lipo MACHPRO 1300 - 2S - 25C- L.G.
ARG
67
12
Blind nut MA 4 mm fixing L.G
68
12
Allen-screw MA 4x20 for landing gear
ADHESIVE NEEDED
CA Super Glue Viscosity Medium
EP5 Glue Epoxy 5 minutes
EP30 Epoxy Glue 30 minutes
FF Thread locker
FL Filler for Epoxy
RADIO E POWER SYSTEM REQUIRED
No. 1 Tx-Rx minimum 11 Channels
No. 6 Standard Metal Gear Servos with Double Bearing
No. 2 Slim Metal Gear Servos Double Bearing
No. 1 Turbine from 60 to 100 N maximum
No. 1 Prewired Cable Kit

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
STABILIZER ASSEMBLY
For assembly the two stabilizer proceed as follows:
1 - Using the template provided (Item 26) trace the outline on the bottom surface for headquarters of the servo control.
2 - Using a Dremel with a cutting disc remove the part drawn and finish with sandpaper.
3 - Install the servo Graupner DS3288 model BBMG in the door servo fiber provided Item 20. Interposing a film. In case of use
different servo verify dimensional compatibility with the servo mount supplied, use a maximum thickness servo of 11 mm.
4 - Place the Servo mount on the installed plate in the Stabilizer and mark the bonding area.
5 - Hone the bonded area of the servo mount.
6 - Glue the servo mount in place using epoxy type EP30 taking care to position the tail plane of the rod command perpendicular to
the axis of rotation of the mobile part.
7 -When dry, remove the servo and the protective film, replace the servo and secure it using the screws included with the servo.
9 - Secure the cover (Item 18) with No. 4 self-tapping screws fastening (Item 34)
10 - Prepare a push rod with axle spacing 70.0 mm using a uniball Pos 42 + aluminum rod L = 40.0 mm
Item 41 + Item 38 M 3 .
11 - Mount on the uniball No. 2 horns (item 21) having care to hone the terminal bonding area of the rod and tighten the whole
package.
12 - Mount the push rod on the servo horn and place the control horn with at 10 mm from the rotation slot open with a bur Ø 2.00
two slots of an appropriate length.
13 - Prepare the adhesive EP30 with filler and fill the slots previously obtained by inserting the group control horn / uniball and
wait to dryness occurred taking care to position the axis of rotation parallel to the axis of rotation of mobile part.
14 - Create a rectangular open on the root rib of the tail plane with the size of the male plug cable Power
15 - Glue the connector with EP 5 leaving protrude about 3/4 mm.

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
16 - Repeat steps 1 to 15 for the other tail plane.
17 - Insert the joiner (item 12) in the hole of the fuselage and mount the tail plane .
18 - made for each stabilizer a pre-drilled hole Ø 1.8 up to pierce the joiner positioned approximately 10 mm from the root rib.
19 - Using the self-tapping screws (item 31) block the tail plane.
20 - Remove the joiners and finish with sand paper the drilling area to eliminate any surplus of material.
WING ASSEMBLY
INSTALLATION OF LANDING GEAR
The DYNAMO is provided for the installation of electric retracts, we suggest ELECTRON retracts (See Pos 50-51-52-53-54) but
you can also mount other types of landing gears with similar dimensions.
To install the landing gear proceed as follow:
1 - Using a Dremel with cutting disc open the landing gear hole and finish with sand paper the edge
2 - Put in the hole of support plate, Nr.4 blind nut with the correct diameter for the landing gear, and glue it with EP30
3 - When dry ,mount the landing gear and take care to pass the cables or air tube in the correct hole

AILERON SERVOS ASSEMBLY
To install the aileron servo proceed as follow:
1 - Using the template (Items 25) drawing the edge for open the hole for mount the servo
2 - Using a Dremel with cutting disc open the hole and finish the edge with sand paper
3 - Install the servo Graupner DS806 BBMG on the servo mount (Item 19). In case of use different servo verify dimensional
compatibility with the servo mount supplied, use only servo with 19mm maximum thickness.
4 - Place the servo mount with servo on the support plate and mark the bonding area.
5 - finish the bonding area with sand paper.
6 - Glue the servo mount in place using epoxy type EP30 taking care to position the plane of the rod command perpendicular to the
axis of rotation of the mobile part.
7 - When dry, remove the servo and the protective film and replace the servo and secure it using the screws included with the servo.
8 - Secure the cover(Item 17) with No. 4 self-tapping screws fastening (Item 34).
9 - Prepare a push rod with axle spacing 82.0 mm using a uniball (Item 42) + aluminum rod L = 50.0 mm (Item 40) + (Item 38) rod
M 3
10 - Mount on the uniball No. 2 horns (Item 21) by having care to hone the terminal bonding area of the rod and tighten the whole
package.
11- Mount the push rod on the servo horn and place the control horn with at 10 mm from the rotation slot open with a bur Ø 2.00 two
slots of an appropriate length.
12 - Prepare the adhesive EP30 with filler and fill the slots previously obtained by inserting the group control horn / uniball and wait
to dryness occurred taking care to position the axis of rotation parallel to the axis of rotation of rotation of the mobile part
ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
FLAP SERVO ASSEMBLY
To install the flap servo proceed as follow:
1-Open on the root rib of the wing a 40x20mm rectangular hole as indicated in the picture, aligned with the hole for the servo on the
first internal rib
2 - With a marker pen drawing, following the measures displayed in the picture, the edge of the hole for the servo horn. with a bur
Ø 2.00 open the hole. take care to place the servo horn in the correct position to permit the right movement of the flap.
3 - install the servo, by passing it through the opening of the landing gear, and fixing it with the screw included with the servo.
4 - Prepare a push rod with axle spacing 72.0 mm using a uniball (Item 42) + aluminum rod L = 40.0 mm (Item 40) + (Item 38) rod
M 3.
5 - Mount on the uniball No. 2 horns (Item 21) by having care to hone the terminal bonding area of the rod and tighten the whole
package
6 - Mount the push rod on the servo horn and place the control horn with at 10 mm from the rotation slot open with a bur Ø 2.00 two
slots of an appropriate length.
7 - Prepare the adhesive EP30 with filler and fill the slots previously obtained by inserting the group control horn / uniball and wait
to dryness occurred taking care to position the axis of rotation parallel to the axis of rotation of the mobile part
WIRING WING ASSEMBLY
Is possible buy the pre-cabled kit (Item 62) (Optional), or in alternative made the wires with all connectors by yourself. On the root
rib of fuselage and of the wing you can find the hole for mounting the connectors.

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
FUSELAGE ASSEMBLY
RUDDER
To install the rudder servo proceed as follows:
1 - Using the template provided (Item25) drawing the outline for the quarters of the Servo .
2 - Using a Dremel with a cutting disc remove the part drawn and finish with sandpaper
3 - Mount the Servo Graupner DS806 BBMG in the servo mount provided (item19). In case of use of different actuators verify the
dimensional compatibility use only servos maximum thickness of 19 mm .
4 - Place the servo mount with servo on the support plate and mark the bonding area.
5 - Finish the bonding area with sand paper.
6 - Glue the servo mount in place using epoxy type EP30 taking care to position the plane of the rod command perpendicular to the
axis of rotation of the movable part perpendicular to the axis of rotation of the movable part .
7 - For when dry remove the servo and the protective film and replace the servo and secure it using the fixing screws supplied with
the actuator .
8 - Secure the cover(Item 17) with No. 4 self-tapping screws fastening (Item 34)
9 - Prepare a push rod with axle spacing 82.0 mm using a uniball (Item 42) + aluminum rod L = 80.0 mm (Item 39) + (Item 38) rod
M3
10 - Mount on the uniball No. 2 horns (Item 21) having care to hone the terminal bonding area of the rod and tighten the whole
package.
11- Mount the push rod on the servo horn and place the control horn with at 10 mm from the rotation slot open with a bur Ø 2.00 two
slots of an appropriate length.
12 - Prepare the adhesive EP30 with filler and fill the slots previously obtained by inserting the group control horn / uniball and wait
to dryness occurred taking care to position the axis of rotation parallel to the axis of rotation of mobile part.
FRONT LANDING GEAR ASSEMBLY
The DYNAMO is provided for the installation of electric retracts, we suggest ELECTRON retracts (See Pos 50-51-52-53-54), you
can also mount other types of landing gears with similar dimensions.
For the assembly of the Landing gear proceed as follows:
1 - Using the template (Item23) drawing the edge for open the hole for mount the landing gear.
2 - Using a Dremel with cutting disc open the landing gear hole and finish with sand paper the edge.
3 - Put in the hole of support plate, Nr.4 blind nut with the correct diameter for the landing gear, and glue it With EP30.
4 - When dry mount the landing gear and take care to pass the cables or air tube in the correct hole.

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
STEERING GEAR SERVO ASSEMBLY
1 - Mount the servo Graupner DS806 BBMG in the pre-cutting hole on the front plate and fix the servo with self-tapping screws
provided.
2 - Prepare a push rod with axle spacing 50.0 mm using a uniball (Item 42) + aluminum rod L = 40.0 mm (Item 41) + (Item 38) rod
M 3.
3 - Connect the rod at the servo horn and at the part of the nose wheel steering control.
4 - Pass the servo cable through the hole on the second rib.
TURBINE SOPPORT ASSEMBLY
For mounting the turbine proceed as follows:
1 - Gluing simultaneously the rib (Item2) at the fuselage and the longitudinal plates (Item 9) with epoxy Ep30 and
filler checking the perfect alignment of the joints.
2 - When dry proceed with the placement of the 4 Blind nut M4 (Item 36) which together with the M4 screws (Item 37) will use to
fix the turbine

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
TURBINE COVER ASSEMBLY
To install the turbine cover, proceed as follows:
1 - Trim the turbine cover as you can see in the picture, take care to leave the way clear for the turbine cone.
2 - Glue with EP5 two blocks of plywood on the inside of the cover.
3 - Realize No. 3 rungs with a carbon tube Ø 2,00 as shown and gluing them securely at the cover using a base in
balsa and epoxy resin with filler EP30.
4 - Mark at the pins position on the fuselage and make No. 3 holes Ø 2.00 mm.
5 - Paste No.3 plywood blocks thickness 3 mm inside the fuselage at correspondence of the holes.
6 - Secure the cover with No. 2 self-tapping screws Ø 2.2 x 10 mm (Item 34).
INTAKE
To realize the air intakes proceed as follows:
1 - Drawing the cutting profiles as shown in the picture.
2 - Using a Dremel with a cutting disc remove the part drawn and finish with sandpaper.
RIB FOR SUPPORT ELECTRONIC PLATE ASSEMBLY
To install the rib proceed as follows:
1 - Bonding with epoxy EP5 the small support plate (Item6) to the rib (Item 5) .
2 - Fix into the 4 holes No. 4 blind nut M3 (Item 33).
3 - Paste the rib to the fuselage using epoxy resin with filler EP 30 after welding in place with super glue CA.
The correct positioning is obtained with the two electronic plate provided Item 3 - 4.

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
JOIN WING / FUSELAGE
To install the screws for joining the wings proceed as follows:
1 - Drill a hole in the Root rib with a 5.5 mm diameter hole, on both wings.
2 - Insert the main joiner (Item11) in the fuselage.
3 - Insert both wings until they are perfectly juxtaposed to the fuselage and the pivot fit perfectly in their seats.
4 - Mark the location of the holes .
5 - Remove the wings and drill with a Ø 5.5 mm the fuselage in the two previous references.
6 - Insert the two M5 blind nuts (Item 30) and glue them with epoxy EP30 and wait until drying.
7 - Put the wings and using the two supplied M5 allen-screw (item 29) and the two steel washers (item 35) fasten until the wings
touch the fuselage.
UAT AND MAIN TANK ASSEMBLY
1 - Assembly the UAT(item 15) and the tank 1.6 lt. (Item 14) realizing the various holes and inserting the fittings supply .
2 - Using the Tygon tube (Item43) achieve the necessary connections according to your fuel system / type of turbine.
3 - Insert the UAT into the appropriate area on the back plate and secure it with two band.
4 - Insert in the half-rib (Item16) for blocking the main tank no. 3 blind Nut M3 nuts (Item 33).
5 - Glue in the first place (for the 2,5 lt use the second seat), with epoxy resin EP5, the main tank support (Item 1).
6 - Prepare a hole for the passage of the overflow pipe at one of the air intake.
7 - Place the tank and secure it with the half-rib and by two bands.
CANOPY ASSEMBLY
To assembly the canopy proceed as follows:
1 - Remove part of material of canopy as shown in the images using a Dremel with a cutting disc and finish
the edges with sandpaper.
2 - Insert at the center of the canopy a carbon tube Ø 8.00 mm by drilling a hole and glue it with epoxy EP30
leaving protrude about 15 mm.
3 - Make a hole in the edge of the fuselage perfectly matching the tube of Ø 8.00mm.
4 - Place the canopy on the fuselage and drill about 14 mm from front end of canopy a hole Ø 3.00 until
pierce also the underlying part.
5 - Remove the canopy and realize a counter hole of 3.2 mm for the passage of the head of the allen-screw
M3 (item 32).
6 - Glue into the hole of the fuselage a blind nut M3 (Item 33) and wait to dryness.
7 - Place the canopy into position and lock it with the allen-screw M3 and verifying the correct coupling.
8 - Glue the blocks in L on the edge of the canopy with epoxy type EP5, about half 'of the length of the fuselage.
9 - Using a dremel to open two slots some millimeter longer than 'L' blocks, on the fuselage edge, at the same position where you
glued the Blocks on the canopy

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
FLAME PROTECTION ASSEMBLY
To install the flame protection proceed as follows:
1 - Place the aluminum protection plate (Item 13) on the lower terminal part of the model and mark with the positions
of the holes on the fuselage.
2 - Glue the Derlin blocks (Item 24) on the marked spots by cyanoacrylate glue, and wait for the perfectly drying.
3 - Place the plate (Item 13) and begin to fix with self-tapping screws (Item 34).
4 - Proceed by manual deformation to align the plate following the curvature of the fuselage and secure also the outer
edges with self-tapping screws (Item 13).

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone] E mail :
[email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
BATTERY
DYNAMO has been provided for the insertion of batteries packs on the compartment where you installed the nose gear steering
servo.
In this compartment are easily placed:
No. 2 2220 2S 35C Lipo batteries to power the on-board electronics
No. 2 2220 2S 35C Lipo batteries to power the turbine
No. 1 1350 2S 35C Lipo batteries to power electric Landing gear
ELECTRICAL WIRING
For electrical wiring we recommend to purchase the kit pre-wired cables supplied by us, otherwise provided by your-self to make the
right wiring in according with the layout choose for the model.
For the cables of the elevators, rudder and wing servos, we suggest to use Bauden spring steel as a probe.
The electrical connections to the wings including any electric landing gear connections can be made using the MPX connectors with
their boxes to be screwed on root-rib after have draw and cut a proper seat, while the connection to the
Elevator can be made with glued with epoxy resin the connector as shown in the following images:
ELEVATOR WING
BALANCING
On DYNAMO has been provided the opportunity to enter a counterweight variable depending on the type of turbine and system
adopted by the Customer. using the hole on the first Rib on the nose of the model that allows you to contain within about 500 grams
of lead weights.
Based on the tests performed with almost all the engines it was necessary to insert about 500 grams of lead weights to get a pre
balance to be refined after the assembly of all the accessories and battery power.
The best flight results on the basis of tests carried out have shown that the best position of the center of gravity (CG) is a 155,00 mm
measured from the leading edge of the wings to the fuselage at the point of joint.

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
BASIC SET UP
To get the best flight performance from your DYNAMO we recommend to use the following Set-Up:
15mm
up
15mm
up
Aileron
0,00
center
Elevator
0,00
center
15mm
down
15mm
down
Flight
13mm
right
Flap
0,00
center
Rudder
0,00
center
0,00
down
13mm
left
Mix Rudder - Elevator: Elevator 1mm UP
Mix Elevator - Turbine
Turbine Minimum --> Elevator 0
Turbine Max --> Elevator 1mm DOWN
15mm
up
14mm
up
Aileron
0,00
center
Elevator
-1 mm
center
15mm
down
14 mm
down
Take OFF
13mm
right
Flap
0,00
center
Rudder
0
center
25mm
down
13mm
left
Mix Rudder - Elevator: inactive
Mix Elevator - Turbine
Turbine Minimum --> Elevator 1 mm DOWN
Turbine Max --> Elevator 2mm DOWN
14mm
up
14,00
up
Aileron
0mm
center
Elevator
-4mm
center
14mm
down
14mm
down
Landing
13mm
right
flap:
0,00
center
Rudder
0,00
center
70mm
down
13mm
left
Mix Rudder - Elevator: inactive
Mix Elevator - Turbine
Turbine Minimum --> Elevator 3 mm DOWN
Turbine Max --> Elevator 5mm DOWN

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
With this set-up you can fly in a very wide speed range thanks to the high stability performance of the model and at the same time
you can have a great acrobatic experience. thanks to the Stall Wing practically non-existent and landings speeds so low you will be
amazed.
PAINT SCHEME
The high mould quality of DYNAMO permit on gelcoat base to apply the PVC stencil, realized by ARG, and sold as optional for
have two kind of paint scheme SPORT UNO and SPORT ZERO (please check the Price list)
SCHEME SPORT UNO
SCHEME SPORT ZERO

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
For customize your Model you can choose the follow two paint scheme realized with hand painting
SCHEME NASA
SCHEME MIRCO PECORARI Special Edition

ARG - ABRAHAM REYNOLDS GROUP di Luciano De Pace & C. S.A.S.
Viale Paradiso 19 - I - 10040 RIVAROSSA - (TO) Tel . : [phone] - Fax. : [phone]
E mail : [email protected] Web: www.argweb.eu Web DYNAMO : www.dynamo-jet.it
WARRANTY
1 - ARG S.A.S. guarantees only the physical integrity of the Products at the time of delivery (hereinafter, the "Guarantee ARG Sas "
) . The warranty covers defects or malfunctions identified out of the box and does not cover breakages, defects or damage from falls,
misuse, improper installation, wear and tear over time. In case of operation of Warranty, Customer will be entitled only to repair or
replace the product if required , at the discretion of ARG Sas that can be performed using the same product and / or with equivalent
features to the problematic one, being excluded the right of the Customer to compensation for any further damage caused or related
to the use and / or use of the faulty product .
Any defects covered by warranty must be reported by the customer, subject to forfeiture , no later than 7 (seven) days from the date
of delivery by email to [e-mail] or a fax to 011-9528399 explaining the defect found .
Once you have our permission to return to where it will be assigned a case number inside the RMA customer ONLY then will send
the material to our office. The return of the product may only be charged to the customer , without prejudice to his responsibility for
any possible damage incurred during the transport. The costs of returning goods, are to be understood against ARG Sas for the entire
duration of the warranty.
To exercise the warranty is sure to keep the purchase invoice or sales receipt and the Bill of Shipping , original packaging and / or
packaging complete products , manuals and any original accessories present at the time of the product .
In the event that after the inspection carried Technical / use product / prove the functioning will be charged € 50,00 VAT included in
reimbursement of costs incurred to verify the defect + shipping , upon receipt of payment from the Customer we will be ship the
product to the customer .
In the case of products whose defect is attributable to causes not covered by the warranty , ARG Sas will send the customer an
estimate of repair and only after written acceptance by the customer , ARG Sas will give way to the repair . Items returned for repair
will be shipped only after the payment of repair and transport cost. If the customer does not accept the quote and does not
communicate the desire to regain the material at the end of the 30 days since communication will be disposed of.
2 - Notwithstanding the provisions of article 1 , ARG S.A.S. does not provide any guarantee on the products additional to that
provided by individual producers . Technical support and warranty work on products are made , where applicable, by the individual
producers , according to the terms and conditions listed in the documentation attached to the Products.
In particular , ARG S.A.S. does not give any guarantee about the compatibility of products with other products or equipment used by
the customer, nor give any guarantee regarding the suitability of products for the specific use intended by the customer.
3 - Without prejudice to the case of willful misconduct or gross negligence of ARG Sas , It is now agreed that, if found responsible
for ARG Sas in any capacity against the customer - including the case of default, in whole or in part, the obligations assumed by
ARG Sas against the Customer as a result of the execution of an order responsibility for ARG Sas can not be higher than the price of
the Products purchased by the Customer from ARG Sas and for which the dispute arose .
SAFETY - WARNING
Please pay attention this RC aircraft is not a toy !
If misused, it can cause serious bodily harm and damage to property.
Fly only in open areas, preferably in official flying sites, following all instructions included with your radio and turbine.
This plane is a compromise between a trainer jet and an aerobatics jet, it is NOT a pylon racer or speed jet for this reason we hardly
recommend:
Do NOT fly your airplane at to high speeds, because this may cause structural failures or fluttering surfaces
The plane has been tested until 250 km/h, flying the plane over this speed is not recommendable.
In this respect, since ARG S.A.S. as the manufacturer of the product called DYNAMO can not oversee how to use it.
The same ARG Sas assumes no responsibility for any damage caused to persons and property by use of the Dynamo. The use of the
product called DYNAMO by the customer automatically implies acceptance of full and total responsibility of the Customer for any
damage to persons and property caused by or arising directly or indirectly. Tacitly confirm that you have read and understood all the
installation instructions contained in this installation Manual before using the same above.
In the event that the customer does not intend to take total responsibility is obliged to return the product to ARG Sas within 7 days
of receipt of the product purchased, uncut and complete package which will be advised on receipt ARG Sas will after verification of
integrity 'of the product to a full refund of the product purchased, net of transport costs by bank transfer within 7 days. of receipt.
Many thanks to purchase our products, ARG Team wishes You good fly !