ARGEAD MINOR-PLUS 3V User manual

INSTRUCTION MANUAL
“MINOR-PLUS 3V” SHEARING PLANT
ARTURO GINES,S.C.
Marcial,1
50300 CALATAYUD (Zarago a) (SPAIN)
Tel: [phone] (office) / [phone] (Workshop)
Fax: [phone]
www.arturogines.com / e-mail: [e-mail]

EUROPEAN DIRECTIVES
The “MINOR-PLUS 3V” complies with the main req irements of the
following Comm nity Directives:
- Machines Directive 2006/42/CE
- Low Voltage Directive 2006/95/CE
- Electromagnetic Compatibility Directive 2004/108/CE
ADDRESS AND CONTACT INFO
ARTURO GINES,S.C.
Marcial,1
50300 CALATAYUD (Zarago a) (SPAIN)
Tel: [phone] (office) / [phone] (Workshop)
Fax: [phone]
www.arturogines.com / e-mail: [e-mail]
-9-
CONTENTS
1-2—SAFETY REGULATIONS
3 - START UP
4-5 - EXPLODED VIEW “MINOR PLUS 3V” MOTOR
6-7– EXPLODED X-125-T ARM
8–ELECTRICAL CONNECTIONS
CHARACTERISTICS OF THE MOTOR
9– EUROPEAN DIRECTIVES
CONTACT INFORMATION
WHEN THIS SYMBOL APPEARS IN THE INSTRUCTION
BOOK, IT INDICATES A POTENTIALLY HAZARDOUS
SITUATION. IT IS RECOMMENDABLE TO TAKE
PRECAUTIONS.

SAFETY REGULATIONS
- Ens re the electric voltage of the motor is the same as the grid to which it
will be connected. ( READ THE CHARACTERISTICS ON THE MOTOR PLATE ).
- Use sockets for the connection that have defa lt c rrent protection and are
properly earthed.
- The motor has a do ble switch: starter and stop.
Start the motor by p shing the green switch and then p lling the cord on
the other switch.
Stop by p lling on the cord again.
- If the c rrent is stopped while the motor is r nning, it will a tomatically dis-
connect. This means that when the electricity comes back on, the green
switch needs to be pressed to se the cord switch.
- When shearing is finished, switch off the electricity by pressing the red
switch and disconnecting the motor from the grid.
- Do not se a wet motor and do not shear in very damp places.
- Check the state of the motor and its connector cable reg larly. If any
anomalies are fo nd, cons lt the AUTHORISED TECHNICAL SERVICE.
- Place the connector cable at height to avoid damage from animals or snag-
ging which may ca se accidents.
- Keep the machine o t of children's reach and of people who are nfamiliar
with handling the eq ipment.
- Shear in areas with no children or animals.
- Use s itable footwear and clothing, in addition to gloves and earm ffs as the
noise emission is greater than 70db (A).
- Work with a s spended motor that is sec rely held in place to stop it falling
otherwise serio s accidents may occ r.
- Do not shear in the rain or on stormy days.
-1-
ELECTRICAL CONNECTIONS
LINE SWITCH
EARTH
WHITE
BLACK
BROWN
MOTOR CORD SWITCH
TECHNICAL CHARACTERISTICS
TYPE : 71/50 CEI—34 MOD. “MINOR PLUS 3 ”
RPM : 2.800 / 3.200 / 3.400
HP : 0,50
: 230
Hz : 50
SERIES NO.:
DATE OF MANUFACTURE:
-8-

EXPLODED IEW: 1.70m X-125-T flexible drive
- 7 -
SAFETY REGULATIONS
- Do not shear in areas where the ambient temperat re is not between
0º and 40º.
- Do not shear in areas near to explosive objects or gases.
- Do not block the fan o tlet on the motor.
- When the machine needs to be cleaned or repaired, disconnect the mo-
tor from the grid.
- This machine is designed for shearing sheep, goats and camelids; se
of this machine on other animals is prohibited.
- When the machine is not in se, store it in a dry place to prevent oxi-
dation of the components.
- The shearing arm is connected to a safety cl tch to prevent snagging
and protect against accidents.
-2-
No. DENOMINATION
34 Bayonet
1018 Flexible terminal sleeve M 6x100
1019 Threaded bolt M 6x100 / W 5/16
1022-R Terminal sleeve cover M 22x150
1023-L Threaded sleeve cover M 22x150
3001-L Cover with terminals
3002-L Flexible with terminals
3003 Motor co pling n t 10 H
3004 Flexible terminal sleeve M 9x125
3005 Terminal sleeve cover
37-157 Bearing 6001-ZZ
37-160 Crosshead bearing M 9x125
37-161 Male-socket cl tch M 14x125
37-162 Female-socket cl tch M 14x125
37-163 Axis-cl tch stem W 5/16
37-164 Spring-cl tch
37-165 N t - cl tch W 5/16

START UP
- Connect the motor to the grid (220v A/C) . ( READ THE SAFETY INSTRUC-
TIONS ).
- Thread the arm onto the motor witho t connecting the scissors (left-hand
thread).
- Start the motor by p shing the green switch and then p ll on the cord.
- Connect the scissors, p shing towards the inside of the arm.
- Before starting to shear, caref lly read the Instr ction Man al for the Scis-
sors.
- Stop the motor by p lling on the cord again.
- To remove the scissors from the arm: p sh towards the inside, t rn half a
circle anticlockwise and p ll o twards.
- After completing the shearing, disconnect the motor from the grid.
- This machine has three speeds (2,800, 3,200 and 3,400 r.p.m.); the most
s itable speed is dependent on the conditions of the livestock and the ability
of the shearer.
Change speed by removing the protective g ard and adj sting the position
of the belt (no tools needed), checking the belt is perfectly aligned between
the two p lleys.
P t the protective g ard in place.
This action m st be ndertaken with the motor disconnected from the grid.
-3-
-6-
EXPLODED IEW: X-125-T FLEXIBLE DRI E

COMPONENTS OF THE “MINOR-PLUS 3 ” UNIT EXPLODED IEW: MINOR-PLUS 3 MOTOR
No. DENOMINATION PARTS
400 Motor handle 1
401 B shing 2
402 Screw W 1/4x9 2
403 Belt protection g ard 1
404 N t W 3/8 2
405 Al mini m p lley set 1
406 Allen thread M 6x10 2
407 N t W 7/16 1
408 Al mini m motor p lley 1
409 Poly-V belt (18") 1
410 Pin 32mm diameter 1
411 Bearing 6201-ZZ 2
412 Axis nit 1
413 Body nit 1
414 Rotating lip 1
415 Tension spring 1
416 Handle brackets 2
417 Screw w/n t M 6x15 4
418 Motor mo nting g ard 1
419 Screw M 6x20 4
420 Tensor spring angle 1
421 Washer 1
423 J nction box 1
424 Capacitor 14mf 1
425 220v Switch 1
426 Switch cord 1
427 Minor Pl s 220v Motor 1
428 Connector cable 1
-5-
-4-