Argo ARGO 245C User manual

EG
I
F
D
E
P
GR
OPERATING INSTRUCTION ●ISTRUZIONI D’USO ●NOTICE D’UTILISATION
BEDIENUNGSANLEITUNGEN ●INSTRUCCIONES DE USO
MANUAL DE INSTRUÇÕES ●ΟΟ∆∆ΗΗΛΛΙΙΕΕΣΣ ΧΧΡΡΗΗΣΣΕΕΩΩΣΣ
INSTALLATION INSTRUCTION ●ISTRUZIONI D’INSTALLAZIONE ●NOTICE D’INSTALLATION
INSTALLATIONSANLEITUNGEN ●INSTRUCCIONES DE INSTALACION
INSTRUÇÕES DE INSTALAÇÃO ●
OODHGIES TOPOQETHSHS
ARGO 245C
ARGO 3SC
37.4252.019.106/2006
Air conditioner • Climatizzatore d’aria • Climatiseur
Klimagerät • Acondicionador de aire
Aparelho de ar condicionado • ΚΚλλιιµµααττιιοοττιικκοοϖϖ
COOL / DRY / FAN COOL / DRY / HEAT / FAN
ARGO 235H
ARGO 3HP

If you have problems or questions concerning your Air
Conditioner, you will need the following information. Model
and serial numbers are on the nameplate applied on the unit.
Model No.
Serial No.
Date of purchase
Dealer’s address
Phone number
The following symbols used in this manual, alert you to
potentially dangerous conditions to users, service personnel
or the appliance:
This symbol refers to a hazard or unsafe practice which
can result in severe personal injury or death.
This symbol refers to a hazard or unsafe practice which
can result in personal injury or product or property damage.
CONTENTS
2
PRODUCT INFORMATION ALERT SYMBOLS
EG
WARNING
CAUTION
This air conditioner is equipped with cooling, drying and fan functions , cooling, drying, heating and fan
functions . Details on these functions are provided here following; refer on these descriptions
when using the air conditioner.The easy installation double-duct technique is on licence of Olimpia Splendid.
NOTES
COOL/DRY/FAN
COOL /DRY/HEAT/FAN
DECLARATION OF CONFORMITY
This product is marked as it satisfies
Directives.
- Low voltage no. 73/23/CEE and 93/68/CEE.
- Electromagnetic compatibily no.
89/336/CEE, 92/31/CEE and 93/68/CEE.
This declaration will become void in case of
misusage and/or non observance though
partial of Manufacturer’s installation and/or
operating instructions.
COOLING
OUTDOOR TEMPERATURE 43°C D.B.
ROOM TEMPERATURE 32°C D.B./23°C W.B.
OUTDOOR TEMPERATURE 19°C D.B.
ROOM TEMPERATURE 19°C D.B./14°C W.B.
OPERATING LIMITS
HEATING
OUTDOOR TEMPERATURE 24°C D.B./18°C W.B.
ROOM TEMPERATURE 27°C D.B.
OUTDOOR TEMPERATURE -8°C D.B./-9°C W.B.
ROOM TEMPERATURE -
OUTDOOR TEMPERATURE 43°C B.S.
ROOM TEMPERATURE 32°C B.S. / 80% R.H.
OUTDOOR TEMPERATURE 16°C B.S.
ROOM TEMPERATURE 16°C B.S. / 80% R.H.
MAXIMUM CONDITIONS
MINIMUM CONDITIONS
MAXIMUM CONDITIONS
MINIMUM CONDITIONS
DEHUMIDYFING (DRY)
MAXIMUM CONDITIONS
MINIMUM CONDITIONS
INFORMATION FOR
CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE
WITH THE EUROPEAN
DIRECTIVE 2002/96/EC
At the end of its working life this
equipment must not be disposed of as
an household waste.
It must be taken to special local
community waste collection centres or
to a dealer providing this service.
Disposing of an electrical and electronic
equipment separately avoids possible
negative effects on the environment
and human health deriving from an
inappropriate disposal and enables its
components to be recovered and
recycled to obtain significant savings
in energy and resources.
In order to underline the duty to dispose
of this equipment separately, the
product is marked with a crossed-out
dustbin.
PRODUCT IDENTIFICATION 3
SIGNALING LAMPS 3
ACCESSORIES SUPPLIED WITH THE UNIT 4
INSTALLATION 4
BEFORE USING THE APPLIANCE 7
USING THE REMOTE CONTROL UNIT 8
REMOTE CONTROL UNIT 9
HOW TO SET THE PRESENT TIME 10
COOLING 10
HEATING 10
AUTOMATIC OPERATION 10
DEHUMIDIFYING (DRY) 11
FAN ONLY 11
ADJUSTING THE FAN SPEED 11
SLEEP MODE 11
SETTING THE TIMER 12
ADJUSTING THE AIR FLOW DIRECTION 12
HOW TO DISCHARGE THE CONDENSATE WATER 13
OPERATION WITHOUT THE REMOTE CONTROL UNIT 14
TIPS FOR ENERGY SAVING 14
TROUBLESHOOTING 14
BOYLER CONNECTION KIT 15
CARE AND CLEANING 15

3
EG
PRODUCT IDENTIFICATION
1. Wireless remote control unit
2. Signaling lamps
3. Supply air deflector
4. Lateral air intake grilles
5. Front air intake grille
6. Air filter
7. Electric cable with plug
8. Air inlet hole
9. Air outlet fan
10. Suspension panel
11. Service tube for condensate discharge
12. Tube for condensate discharge
(heat pump models)
SIGNALING LAMPS
1. Receiver : receives signals transmitted from the remote
control.
2. Timer lamp: This lamp lights up when the system is
being controlled by the timer or sleep mode.
3. Standby lamp: This lamp lights up when the air
conditioner is connected to the power and ready to
receive the remote control command.
4. Operation lamp: This lamp lights up during operation.
It blinks once to announce that the remote control signal
has been received and stored. It blinks continuously
during the protection modes (defrosting, etc.).
5. Operation button (without remote control): Push the
button to change from one operation mode to the other
as shown here following.
The OFF position does not disconnect the power. Use
the main power switch to turn off power completely.
WARNING
Heat pump models
Cooling only models
1
23
4
5
6
7
8
9
10
11
11
12
Heat pump models
Cooling only models

4
EG
The installation should be carried out by a qualified installer,
following the instructions as shown.
INSTALLATION SITE SELECTION
●In case you should replace a radiator in an already existing
heating system, follow the instruction of the boiler
connection kit
●The wall must be a perimeter one.
●Fix the unit at a minimum height of 10 cm and a maximum
height of 100 cm.
●Select a sufficiently strong location to support the weight
of the unit.
●Allow access for maintenance operation around the unit.
●Make sure that there are no obstacles around the unit
affecting the free circulation of air.
●Avoid installing the unit with the air flow directly toward
passerby people, electric appliances or heat sources.
CAUTION
After the selection of the installation site, according to
the above mentioned points, be sure not to make holes
in areas where electrical wiring or conduits are located,
damaging them.
Make sure that there are no obstacles in the conduits
inside the wall affecting the free circulation of the
external air. The unit must be kept at a minimum
distance of 80 cm from any wall or obstacle.
INSTALLATION
1. PLASTIC TUBE (1pcs.)
2. EXTERNAL GRILLES (2pcs.)
3. INTERNAL GRILLES (2pcs.)
4. TENSION BARS (2pcs.)
5. FULL SCALE DIAGRAM (1pcs.)
6. RAWL PLUGS + SCREWS (15pcs.)
7. REMOTE CONTROL UNIT (1pcs.)
8. BATTERIES FOR REMOTE CONTROL (2pcs.)
ACCESSORIES SUPPLIED WITH THE UNIT
5
1
2
3
4
6
7
8
Level
Full scale
diagram
Mill
MOUNTING OF THE UNIT
- Apply at the wall the full scale diagram, fix and level it.
- Drill the two holes Ø 162 mm and eventually the hole
Ø 35 mm in case of heat pump unit for the condensate
drainage toward the outside (assure a positive slope
toward the outside).

5
EG
- Insert in the two holes the supplied plastic tube; cut it at
the right length: it is necessary to measure the thickness
of the wall and subtract 70 mm.
- Fix the two anti-intrusion grilles and the two external grilles
with the blades toward the bottom using wall rawl plugs
and screws.
- In case it is not possible to fix the two external grilles
directly at the wall, hook the two grilles to the internal
ones using the supplied tension bars, as follows:
a) Bend them, fix the hook of the spring, insert them
inside the tube and open them toward the outside.
b) Choose the proper hook of the tension bar in order to
lengthen the spring of 15-20 mm and hook it to the
internal grille.
c) Eliminate the exceeding part of the tension bar cutting
it near the hooking points.
Spring
hook
3
3
a
- In case of very thin walls (less than 10 cm) it is necessary
to mount the internal anti-intrusion grilles on the back of
the unit removing the gaskets (a) from the back side and
applying them around the grilles. The tube and the external
grilles will not be used.
CAUTION
The manufacturer assumes no responsibilities if this
safety instruction is not observed.
INSIDE OUTSIDE