Argos Home Atlas 3ft Bed 664/9458 User manual

Atlas 3ft Bed
Dimensions
Width - 100cm
Depth - 204cm
Height - 89cm
Issue 1 - 09/04/10
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
Assembly Instructions - Please keep for future reference 664/9458

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• As you unpack and prepare
for assembly, clear an area for
assembly. The parts should be
placed on a carpeted or padded
area to protect them from
damage.
• Parts of the assembly will be
easier with 2 or 3 people.
• Do not discard any of the
packaging until you have
checked that you have all the
parts and pack of fittings.
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• To ensure an easier assembly,
we strongly advise that all
fittings are only finger tightened
druing initial assembly. Only
upon completion of the
assembly should all fixing points
be fully tightened.

Components - Panels
Please check you have all the panels listed below
2
Left footboard post
(dia6.0 x 55cm)
3
Side rail x 2 (192 x 10cm)
9
If you have damaged or missing components,
call the Customer Helpline:
0845 6400800
Left headboard post
(dia6.0 x 90cm)
1
Right footboard
post (dia6.0x 55cm)
4Headboard upright x 3
(dia1.27 x 39.4cm)
5Footboard upright x 3
(dia1.27 x 46.9cm)
6
End horizontal bar x 4
(dia2.5 x 88.8cm)
7Middle horizontal bar x 3
(dia2.5 x 99.5cm)
8
Slat x 12 (dia1.9 x 92cm)
10
Right headboard
post (dia6.0 x 90cm)
2

3
Please check you have all the ttings listed below
42mm Bolt x 24
Ruler - Use this ruler to help correctly identify the screws
A
Large plain washer x 8
E
30mm Bolt x 8
B
Small hex key x 1
H
80mm Bolt x 8
C
Large hex key x 1
I
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
100 20 30 40 50 60 70 80 90 100
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Spring washer x 8
F
Small plain washer x 48
D
Nut x 24
G
Wrench x 1
J
Components - Fittings

4
Assembly Instructions
Step 1
a:
b:
c:
1
2
C
7
8
8
5
C
C
C
Assemble headboard
a: Assemble end
horizontal bar 7and
middle horizontal bars
8to left headboard post
1and right headboard
post 2using bolts Cas
shown in the gure.
Note: The chrome cap
on both posts should be
at the top.
Do not fully tighten
bolts.
b: Insert headboard
uprights 5through
middle horizontal bars 8
to end horizontal bar 7.
c: Attach end horizontal
bar 7to the headboard
uprights and x to the
headboard posts using
bolts C.
8
7
7
8

Step 2
5
Assembly Instructions
7
8
7
C
b:
a:
c:
3
4
C
C
6
7
C
Assemble footboard
a: Assemble end
horizontal bar 7and
middle horizontal bar
8to left footboard post
3and right footboard
post 4using bolts Cas
shown in the gure.
Note: The chrome cap
on both posts should be
at the top.
Do not fully tighten
bolts.
b: Insert footboard
uprights 6through
middle horizontal bar 8
to end horizontal bar 7.
c: Attach end horizontal
bar 7to the footboard
uprights and x to the
headboard posts using
bolts C.
8

Assembly Instructions
Assemble side rails
Three people are needed
here.
Assemble side rails 9
to headboard frame and
footboard frame using
bolts B, spring washers
Fand large plain
washers E.
Note:Do not fully
tighten bolts.
Assemble slats
Assemble slats 10 to the
unit using bolts A, small
plain washers Dand
nuts G.
Note:Re-tighten all the
bolts.
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
Step 3
B
F
E
B
F
E
9
9
10 10
10
10 10
10 10 10 10 10
10
10
A
D
G
D
Step 4

Atlas 3ft Guestbed Trundle
Issue 1 - 21/04/10
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
Assembly Instructions - Please keep for future reference 649/7545
Dimensions
Width - 93cm
Depth - 191cm
Height - 34cm
633/3496

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• As you unpack and prepare
for assembly, clear an area for
assembly. The parts should be
placed on a carpeted or padded
area to protect them from
damage.
• Parts of the assembly will be
easier with 2 people.
• Do not discard any of the
packaging until you have
checked that you have all the
parts and pack of fittings.
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• To ensure an easier assembly,
we strongly advise that all
fittings are only finger tightened
druing initial assembly. Only
upon completion of the
assembly should all fixing points
be fully tightened.

Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components,
call the Customer Helpline:
0845 6400800
Leg x 2 (93.5 x 33.1cm)
2
End x 2 (93 x 21cm)
1Side rail (160 x 9cm)
3
Side rail (160x9cm)
4Slat x 10 (dia1.9x88.6cm) 5

3
Please check you have all the ttings listed below
17mm Bolt x 8
Ruler - Use this ruler to help correctly identify the screws
A
Nut x 4
E
37mm Bolt x 4
B
Wrench x 1
H
48mm Bolt x 20
C
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
100 20 30 40 50 60 70 80 90 100
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Cap nut x 20
F
Plain washer x 44
D
Hex key x 1
G
Components - Fittings

4
Assembly Instructions
Step 1
Assemble ends
Assemble ends 1to
side rails 3and 4
using bolts A.
Assemble legs
Two people are needed
here.
Assemble legs 2to side
rails using bolts B, plain
washers Dand nuts E.
Note: Do not tighten
bolts.
1
3
Step 2
4
A
B
2
A
1
2
D
E

Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
Step 3
Assemble slats
Assemble slats 5to the
unit using bolts C, plain
washers Dand cap nuts
F.
Note: Re-tighten all the
bolts.
Caution:
Ensure the
locking pins are
inserted into the holes
when in use. Failure
to do so could cause a
hazard.
Assembly is complete.
C
D
D
F
55
555
55
5
55