Argos Home Lawson 402/4439 User manual

MADE IN
BRITAIN
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
More help is available throughout this
booklet by scanning in the QR codes
or typing in the links
WARNING!
In order to prevent overturning, this product must be
used with the 2 wall attachment devices provided
Assembly Instructions - Important: Retain these instructions
for future reference
Dimensions
Width - 100cm
Depth - 39.5cm
Height - 73.5cm
Lawson - Desk
Issue 8 - 05/10/17
402/4439
412/3392
797/7916
412/6416

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
1
Care and maintenance
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Regularly check all fastenings
to ensure that they are properly
tightened.
• Warning: This unit weighs
approximately 20kgs.
Please lift with care.
• Assembly to be carried out by
a competent adult only.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions
- otherwise a safety risk can
occur if incorrectly installed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall
using the 2 overbalance
protector kits supplied.
• Dispose of all packaging
carefully and responsibly.
• Do not use this item if any
components are missing or
damaged.

Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below
When applicable, remove any protective film
from the panels before they are used
2
1Left End (DF2766)
(71.6 x 39.2cm)
Modesty (DF2772)
(62 x 15.7cm)
Door (DF2771)
(32.6 x 32.1cm) Back (X707-353)
(70.7 x 35.3cm)
Shelf (DF2770)
(32.7 x 37.3cm)
Upright (DF2767)
(71.6 x 39.2cm)
Right End (DF2768)
(71.6 x 39.2cm)
2 3
4 5 6
7
89
Base (DF2769)
(32.7 x 39cm) x 2
Top (DF2765)
(99.6 x 39.6cm)

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Tools required
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H
K
I
Nail (F51) x 14
J
Large locking cam
nut (F900) x 18
Metal dowel (F901) x 18
Rule
Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Square
Bradawl
Spirit
level
Shelf stud (F110) x 5
C
Hinge plate
(F523) x 2 Hinge (F522) x 2
13mm Screw (F63) x 425mm Screw (F50) x 2
Handle (F236) x 1
Plastic Nail (F91) x 6
Strap Screw Washer x 2
Overbalance protector kit (F269) x 2

Finished
front edge
Assembly Instructions
4
Step 1
Step 2
A
A
A
A
A
B
Prepare the upright
Screw 4 metal dowels
into the upright .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
cam nuts into the
upright .
Note: The arrow on the
locking cam nut must
point towards the hole in
the edge of the panel.
Turn the upright over
Screw 2 metal dowels
into the upright .
B
A
2
B
2
B
A
A
Finished
front edge
Turn the upright over
A
2
2
2
B
B
B
B
Finished
front edge
Prepare the 2 base
panels
Insert 4 large locking
cam nuts into each of
the 2 base panels .
B
5
5B
B
B
B
Finished
front edge
5

Finished
front edge
Finished
front edge
Assembly Instructions
5
Step 3
Step 4
A
B
Fit a base to the
upright
Push a base onto the
upright .
Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the upright .
Note: Turn the large
locking cam nuts as
far as they will go - more
than 1/2 a turn.
2
5
B
2
2
5
Fit the other base to
the upright
Push the base onto
the upright .
Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the upright .
Step 5
Prepare the left end
Screw 4 metal dowels
into the left end .
Insert 2 large locking
cam nuts into the left
end .
Fit 2 hinge plates onto
the left end , making
sure that the slot is
facing towards the
finished front edge.
2
5
B
B
2
Finished
front edge
Finished
front edge
2
5
HA
A
B
B
KH
H
A
A
A
1
B
1
H
1
1
www.youtube.com/watch?v=wIMhUHeLBtg
Hinge Fixing and Door Adjustment

Finished
top edge
Finished
front edge
Assembly Instructions
6
Step 6
5
5
1
Fit the left end
Push the left end
onto the 2 base panels
. .
Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to each of the 2
base panels .
5
5
1
B
B
B
B
B
Prepare the modesty
Insert 4 large locking
cam nuts into the
modesty .
B
7
Step 7
Step 8
7
A
A
Finished
front edge
B
Prepare the right end
Screw 2 metal dowels
into the right end .
Insert 2 large locking
cam nuts into the
right end .
B
A
3
B
3
3

Finished
front edge
Finished
top edge
Assembly Instructions
7
Step 9
Fit the modesty
Push the modesty
onto the upright .
Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the modesty .
Note: Support the
modesty until the right
end has been fitted in
the next step.
Step 10
2
7
7
B
Fit the right end
Push the right end
onto the modesty .
Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the modesty .
7
7
3
B
2
3
7
7
Step 11 A
Prepare the top
Screw 6 metal dowels
into the top .
A
4
A
A
AA
A
Finished
front edge
4

yy
y
y
Assembly Instructions
8
Step 12
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 6 large
locking cam nuts
fitted to the left end ,
the upright and the
right end .
Step 13
3
1
2
3
B
4
1
2
4
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
9
F
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
9
xx
x
x
F
9
www.youtube.com/watch?v=FeaI6541z7o
Squaring up a Chest and tting the Back Panel

Assembly Instructions
9
Step 14
Step 15
Fit the 6 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the left end ,
upright and right end
. .
Carefully stand the
unit up for the next
step.
G
1
2
3
G
G
G
Cx 4
G
G
G
Warning: The
unit is heavy.
Lift with care.
1
2
3
Fit 4 shelf studs
Insert 4 shelf studs
into the holes shown.
Step 16
Fit the shelf
Lower the shelf down
onto the shelf studs .
C
C
6
6
Finished
front edge