Argos Home New Hallingford 652/9482 User manual

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0330 016 1114
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
MADE IN
BRITAIN
Dimensions
Width - 37.5cm
Depth - 40cm
Height - 58cm
Assembly Instructions - Important: Retain these instructions
for future reference
More help is available throughout this
booklet by scanning in the QR codes
or typing in the links
WARNING!
In order to prevent overturning, this product must be
used with the wall attachment device provided
Issue 15 - 13/11/19
New Hallingford - 3 Drawer Bedside
652/9482
673/1902
620/9379
673/2176
618/4999
601/6737
677/5449
618/6959
678/3699
616/9749
887/6449
916/0109

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Warning: This unit weighs
approximately 14kgs.
Please lift with care.
• Assembly to be carried out by
a competent adult only.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions
- otherwise a safety risk can
occur if incorrectly installed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall
using the overbalance
protector kit supplied.
• Dispose of all packaging
carefully and responsibly.
• Do not use this item if any
components are missing or
damaged.
Tools required
Rule
Scissors
Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
Bradawl
Flat-head
screwdriver

Components - Panels
Please check you have all the panels listed below
2
1Left Side (D2307A)
(55.6 x 37.2cm)
2Right Side (D2308A)
(55.6 x 37.2cm)
3
4 5
86 7
9 10
Top (D2306A)
(37.5 x 39.6cm)
Back (X535-366)
(53.5 x 36.6cm)
Rail (D2310A)
(34.1 x 6cm) x 2
Drawer Front (D2309A)
(36.2 x 16.2cm) x 3
Drawer Base (T304-367)
(30.4 x 36.7cm) x 3
Drawer Back (W291-124)
(29.1 x 12.4cm) x 3
Left Drawer Side (W370-124LH)
(37 x 12.4cm) x 3
Right Drawer Side (W370-124RH)
(37 x 12.4cm) x 3

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
3
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
B C
D E F
G H
Small locking cam
nut (F3) x 6
Nail (F51) x 12
13mm Screw (F63) x 18
I
A
Wooden dowel (F22) x 6
19mm Screw (F461) x 6
Metal dowel (F901) x 12
Large locking cam
nut (F900) x 6 Knock-in Peg (F171GY) x 12
J
Handle (F278) x 3
M
Plastic Nail (F91) x 4
L
Wedgefix (F639) x 6
Kb
Ka
350mm long
CL
CR
CR Runner (F424) x 3
CL Runner (F422) x 3
Kc
KdDR
DL
DL Runner (F425) x 3
DR Runner (F426) x 3
9mm Screw (F73) x 18
Overbalance protector
kit (F474) x 1
N

4
Step 1
Assembly Instructions
5
x 3
B
B
B
C
B
B
Groove
C
5
x 3 x 3
x 3
Step 2
Prepare the 3 drawer
fronts
Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .
Note: Tighten metal
dowels up fully against
the panels.
B
5
Prepare the drawer
sides
Insert a small locking
cam nut into the hole
shown on the left drawer
side and right drawer
side .
Note: The arrow on the
locking cam nut must
point towards the hole in
the edge of the panel.
Step 3
C
6
7
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
cam nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
cam nuts clockwise
to secure panels - more
than 1/2 a turn.
6
7
5
C
6
7
C
CC
67
6
7
www.youtube.com/watch?v=3fYL5zB6ZYQ
Drawer Assembly

Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
9
6 7
5
8
6 7
9
8
8
E
6 7
Attach the handle
Attach a handle to
each drawer front
using 2 screws .
Step 7
J
G
5
E
E
E
J
5
G
G
x 3
x 3
x 3
L
L
L
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
L
7
9
6
8
E
Important: Make sure
that the drawer assembly
is square before fitting
the wedgefixes.
5
x 3
7
6
9

Assembly Instructions
6
Step 8
Fit runners to the
drawers
Turn the 3 drawer
assemblies over.
Fit runner , marked
with ‘DR’, to the bottom
edge of the right drawer
side , as shown,
making sure that it is
pushed up against the
back of the drawer front
. .
Use a bradawl to mark
the fixing positions, then
secure with 2 screws .
Fit runner , marked
‘DL’, to the bottom edge
of the left drawer side
using the same method.
6
K d
7
5
I
K c
D
D
D
A
10mm
A
Prepare the 2 rails
Tap 2 wooden dowels
into each rail .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking cam
nuts into each rail .
Note: The arrow on the
locking cam nut must
point towards the hole in
the edge of the panel.
A
A
Step 9
x 2 4
4
D4
5
6
7
x 3
Runners must be
pushed up against
the drawer front
DL
I
I
I
I
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounter Runners
DL
K c
Bradawl
K d
DR
Bradawl

Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 10
a:
Prepare the left side
a: Fit 3 CL runners
to the left side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Mark the top hole of
the runners with a
bradawl and then fit a
screw .
Screw 2 metal dowels
into the left side .
Insert a large locking
cam nut into the left
side . .
Tap a wooden dowel
into the left side .
b:
B
D
1
1
K a
1
H
H
I
K a
B
D
A
A
1
1
1
K a
H
1st
screw
Finished
front edge
CL
CL
I
CL
I
CL
I
CL
H
H
K a
H
CL
H
H
K a
H
CL
H
H
K a
H
B
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounter Runners
Finished
front edge
K a
Bradawl

CR
CR
CR
A
Assembly Instructions
8
Step 11
Prepare the right side
a: Fit 3 CR runners
to the right side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Mark the top hole of
the runners with a
bradawl and then fit a
screw .
Screw 2 metal dowels
into the right side .
Insert a large locking
cam nut into the right
side .
Tap a wooden dowel
into the right side .
B
D
2
2
K b
2
H
H
I
K b
a:
b:
D
B
Finished
front edge
Finished
front edge
A
2
2
2
Join the right side and
rails
Push the 2 rails onto
the right side .
Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the rails .
Note: Turn the large
locking cam nuts as
far as they will go - more
than 1/2 a turn.
B
D
D
2
4
2
4
D
Step 12
Note: Support this
rail until the left
side has been fitted
in the next step.
4
4
K b
H
1st
screw
Finished
front edge
CR
CR
I
CR
I
CR
I
CR
H
H
H
K b
CR
H
H
H
K b
CR
H
H
H
K b
B
Finished
front edge
K b
Bradawl

CR
CR
CR
CR
CR
CR
Assembly Instructions
9
Step 13
Fit the left side
Push the left side
onto the 2 rails .
Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the rails .
D
4
1
1
4
4
B
B
Step 14
Step 15
Shaped
front edge
3
3
Fit the top
Push the top onto
the 2 sides and .
Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the sides
and .
D
3
1 2
1
2
1
2
4
N
Prepare the top
Screw 2 metal dowels
into the top .
Fit the bracket from the
overbalance protector kit
. to the shallow
mark-hole drilled into
the top using 1 of its
screws.
Note: Only fit 1 of the
screws, the other 1 will
be fitted later.
B
3
N
3
N