Argos Home 875/5027 User manual

Grey and Chrome Tidy Rail with Two Rails
Dimensions
Width - 84cm
Depth - 42cm
Height - 99.5/166cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Assembly Instructions - Please keep for future reference
875/5027
Issue 1 - 29/05/10

1
• Check you have all the
components and tools listed on
page 2.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts are a choking hazard.
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the unit as close to its
final position (in the same room)
as possible.
• Assemble on a pad to avoid
damaging the unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• If using power tools, please
follow the safety instructions
supplied with the tools.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
• Dispose of all packaging
carefully and responsibly.
Safety and Care Advice
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit. 
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre. 
Care and maintenance
Important - Please read these instructions fully before starting assembly
as this could damage the unit.
Only use hand screwdrivers.

2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Bottom crossbar x 2
5
Lower side support x 2
2
Hanger x 1
1
Top crossbar x 1
3
Upper side support x 2 (Inserted inside component B)
4
Connector x 4
Lock x 2
Castor x 4Leg section x 2
A
D
B C
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Components - Fittings
Please check you have all the fittings listed below

a:
Assembly Instructions
Step 1
Fitting the Leg section
Note: It would be useful
to ask someone to help
you at this stage.
b: Insert Lower side
support into the Leg
section .
2
2
c: Insert Castors into
the Leg section .
b:
c:
3
a: Insert Bottom crossbar
into the Leg section
.2
5A
B
2
5
2
5
A
B
A
B
B
A
C
A
C
A
C
A
C
A
C
A
B
A
B
A
B
2
2
2
2
A
B
A
B

b:
a:
Assembly Instructions
Step 2
A
A
A
AA A
A
A
Fitting the Rail
a: Insert Top crossbar
into the Connectors .
A
A3
3
3
4
b: Insert Upper side
support into the
Connectors .
A
A
4
4
4

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Assembly is complete.
b:
c:
Assembly Instructions
Step 3
Fitting the Hanger
a: Insert Hanger into
the Locks .
A
D1
b: Insert Locks into
the Lower side support
.
Insert Locks into
the bottom of Upper side
support .
Note: Align all the holes
of the Lower side
support , Upper side
support & Locks
before locking.
A
D
A
D
A
D
4
4
2
2
a:
A
DA
D
1
fig.1
4
4
2
2
1
A
D
A
D
C: Set the height of the
unit
Ensuring the Locks
are loosened, slide the
Upper side support to
the desired height and
tighten the Locks to affix
in position as shown in fig.1.
4
A
D
Adjustment Range:
99.5-166 cm.
Note: Please hold
Upper side support
and pull downward. It
will be fixed if locked or
will glide downward if
unlocked.
4
A
D
4
A
D