Argos Home Ohio TV Unit 309/6561 User manual

MADE IN
BRITAIN
Dimensions
Width - 120cm
Depth - 39.5cm
Height - 61.5cm
Ohio - TV Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 16/10/13
Important - Please read these instructions fully before starting assembly
ALR3083
309/6561
Issue 1 - 16/10/14 - Dalton changed to Ohio

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 30kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
1
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D1782A)
(1200 x 395mm)
4
2Left Side (D1783A)
(590 x 357mm)
Right Side (D1784A)
(590 x 357mm)
Base (D1785A)
(1020 x 350mm)
7
5Divider (D1786A)
(480 x 349mm) x 2
Large Shelf (D1787A)
(444 x 348mm) x 2
Small Shelf (D1788A)
(271 x 348mm) x 2
6
1110
Plinth (D1789A)
(1020 x 95mm)
Fascia (D1790A)
(590 x 70mm) x 2
3
8 9
Door (D1808A)
(492 x 342mm) x 2
Small Back (X918)
(504 x 292mm) x 2
12 Large Back (X950)
(504 x 395mm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Electric drill
(do not use for
fitting screws)
A
Wooden dowel (F22) x 6
B
Metal dowel (F901) x 18
C
D
Large locking
nut (F900) x 18
F
H I
19mm Screw (F461) x 4
J K
G
13mm Screw (F63) x 8
E
Shelf support (F121) x 16
Nail (F51) x 22
Hinge plate
(F523) x 4 Hinge (F522) x 4
Handle (F287) x 2
40mm Screw (F910) x 4
L
Plastic Nail (F91) x 5

A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
C
C
C
C
C
J
J
BB
B
B
10mm
A
Prepare the left side
a: Tap a wooden dowel
. into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Screw 3 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
b: Insert 4 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Fit 2 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
A
b:
a:
2
2
2
J
B
2
C
2
J
2
C

Left fascia - holes
nearest this side
A
A
A
Assembly Instructions
5
Step 2
J
C
C
C
C
B
BB
J
J
Prepare the right side
a: Tap a wooden dowel
. into the right side .
Screw 3 metal dowels
into the right side .
b: Insert 4 large locking
nuts into the right
side .
Fit 2 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
A3
B
3
C
3
J
3b:
a:
Step 3
Prepare the 2 fascias
Check that the holes are
in the same place as the
diagrams, as one will be
the left fascia and one
will be the right fascia.
Screw 2 metal dowels
into each of the 2 fascias
. .
Tap a wooden dowel
into each of the 2 fascias
. .
B
9
10mm
A
9
A
x 1
x 1
B
B
B
B
Right fascia - holes
nearest this side
9
9
3
3

Assembly Instructions
6
Step 4a:
b:
Join the left side to
the left fascia panel
a: Push the left side
down onto the left fascia
panel .
b: Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
9
C
2
C
Dowel
this end
9
9
C
B
Left fascia
Right fascia
C
Dowel
this end
2
2
Step 5
Join the right side to
the right fascia panel
a: Push the right side
down onto the right
fascia panel .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right side .
3
9
C
3
3
9

Finished
front edge
Finished
front edge
3
Assembly Instructions
7
Step 6
Step 7
Prepare the base
Insert 4 large locking
nuts into the base .
C4
C
C
C
C
Finished
front edge
plain chipboard surface
4
Fit the base
Push the base onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
C
4
3
4
Step 8
4
plain chipboard surface
C
C
Prepare the 2 dividers
Insert 2 large locking
nuts into each of the
2 dividers .
5
C
x 2
5

Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 9
G
G
G
G
G
5
4
5
A
Step 10
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
Insert 2 large locking
nuts into the plinth .
8
8
A
C
C
C
A
plain chipboard surface
8
5
4
G
Fit the dividers
Attach the 2 dividers
to the base using 4
screws .
Note: To make it easier
to fit the 2 dividers, place
polystyrene blocks from
the packaging
underneath to raise them
up level.
Polystyrene
block
Fit the plinth
Push the plinth onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the plinth
. .
C
8
3
8
plain chipboard surface
3
8
Step 11

Assembly Instructions
Step 12
2
9
8
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the base and plinth
. .
2
C
4
8
2
4
Fit the 5 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
The other plastic nail
taps into the the bottom
edge of the plinth . .
L
L
2
3
L
L
Step 13
8
L
L
L
8
3