Argos CL4124 User manual

MOSES BASKET - ASSEMBLY INSTRUCTIONS
YOUR COMPONENTS/ FITTINGS
x 2 Hood Runners
(to fit into the channels in the hood as shown)
dressing
FRONT
BACK
Insert one hood runner
in the FRONT channel of
the moses basket hood.Insert one hood runner
in the BACK channel of
the moses basket hood.
base
hood
PLEASE CHECK YOU HAVE THE FITTINGS SHOWN BELOW.
Please note: The quantities below are the correct
amount to complete the assembly.
STEP 1 - HOOD ASSEMBLY
Insert the hood runners (E) within the two channels
shown in the hood diagram below.
There are channel openings at both ends.
SCREW POSITION
x 2 Screws x 2 Washers x 2 Wing Nuts x 2 Nyloc Nuts
A B C D
E
A
B
C
D
E
SIDE OF BASKET
OUTSIDE OF BASKET B
F
HOLE IN BASKET
POSITION OF COMPONENTS
INSIDE OF BASKET
Screw should be positioned in the second hole
down closest to the outside of the handle.
2 HOLES DOWN
BASKET HANDLE
INSIDE OF BASKET
HOOD
E
2 X E
STEP 2 - INSERTING SCREW & WASHER
1 X (A) & 1 X (B)
INSIDE OF BASKET
Place the attached screw (A) and washer (B)
through the hole from the inside of the basket
and hold in position. ( See screw position diagram)
Having located the screw with the
washer attached from the inside of
the basket, now attach the BACK
runner E outside of the basket.
FRONT
BACK
STEP 3 - INSERTING THE RUNNERS
FRONT
BACK
Then attatching the FRONT runner
E on top of the BACK runner.
It is essential that BACK runner
is attached first, followed by the FRONT.
HANDLE
INSIDE OF BASKET
Page 1

PLEASE KEEP INSTRUCTIONS FOR FUTURE REFERENCE!
STEP 4 - ATTACHING WING NUT & NYLOC NUT
FINALLY ATTACH THE WING NUT AND LOCKING
NYLOC NUT:
The locking Nyloc nut should be tightened with
a pair of plyers so that it locks and cannot be
undone using finger pressure.
Please note: if the hood of the moses basket
does not stay up,tighten the wing nut slightly.
The Nyloc nut is used for extra security to keep
the wing nut in place.
WARNING: PLEASE MAKE SURE ALL FITTINGS ARE
ACCOUNTED FOR AND THAT NOTHING IS LEFT IN THE BASKET,
AS THESE COULD CREATE A SERIOUS HAZARD TO BABY.
Repeat process 2,3 & 4 to attach hood to the otherside of the basket.
STEP 5 - REPEAT PROCESS
CL4124/CL4285 WHITE WAFFLE MOSES BASKET & FOLDING
STAND
IMPORTANT
READ INSTRUCTIONS CAREFULLY AND KEEP THEM FOR FUTURE REFERENCE
WARNING: This product is only suitable for a child who cannot sit
unaided, roll over and cannot push itself up on its hands or knees.
Maximum weight of the child 9 Kg.
Before picking up the Carrycot, make sure both handles are secure in the
hand of the Carer.
Use only on firm, horizontal level & dry surface.
WARNING: Do not let other children play unattended near the carry cot.
WARNING: Do not use if any part is broken, torn or missing.
Use only replacement or approved parts from Dawson & Rodgers & Co Ltd.
WARNING: Maintaining a safe distance from the strong heat sources
such as electric bar fires, gas fires, etc in the near vicinity of moses basket.
If the mattress is purchased separately, it shall fit well into the
product and the depth from the top of the side of the product should
not be less than 170mm when the mattress is in position of use.
The handles and the bottom should be inspected regularly for signs of
damage & wear.
If the moses basket is intended to be used with a stand, then it
should be checked that the stand is the appropriate size to accommodate
the base of the moses basket. Base size min-max 700-835mm in length
and 300-370mm in width
CLEANING INSTRUCTIONS
BASKET: Sponge lightly with warm water and mild detergent.
MATTRESS: If necessary wash by hand in warm water and mild
detergent. Dry away from direct heat or sunlight. Do not tumble dry. Do not
dry clean.
DRESSING: See care label on product.
Dispose of all packaging safely before use.Complies with BS EN 1466:2004
Dawson Rodgers & Co Ltd, Shenton Road, Sharston Industrial Estate,
Wythenshawe, Manchester M22 4RW
1 X (C) & 1 X (D)
CONTINUED Page 2