Arlight Sens SR-2831-RF-IN User manual

Full Touch RGBW RF Remote Led Control Panel
Parameter
Wiring diagram
Product Size
29.1
86.0
86.0
Unique square color paddesign-
Sensitive full touch new technology
Special glass interface(white&black)
Control 4 zones seperately or synchronously
1)Sender DiagramConnection
LN
SR-2831-AC
110V-230VAC
N
L
VinGND
LN
110V-230VAC
Power Supply
12-24VDC
Feature
Sens SR-2831-RF-IN
Part No. Iuput Voltage Remarks
Current
SR-1009FA 12-36VDC Constant voltage
4x(60-180)W
4x5A
Output
SR-1009EA 12-36VDC Constant voltage
4x(96-288)W4x8A
Remote
Part No. Operation Voltage DIMENSIONS
ø/h (mm)
Operation
Frequency
SR-2831-AC 100-240VAC 86x86x29.1
434MHz/868MHz
Receiver
SR-1009FA3 12-36VDC Constant current
4x(4.2-12.6)W
4x350mA
SR-1009FA7 12-36VDC Constant current
4x(8.4-25.2)W4x700mA
Remarks
Touch Sensor
SR-2831-DC 12-24VDC 86x86x29.1
434MHz/868MHz Touch Sensor
SR-2831-DC
Note:
One receiver can work with 1-8pcs SR-2831
One SR-2831 control multiple receivers
The power supply chosen must be 20% higher than the actual load
2) Connection Diagram for Multiple UnitsReceiver
Power Supply
12-36VDC
LN
110V-230VAC
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Key
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Key
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Key
Installation
12-2 4VD C
Powe r Sup ply
SR-2831-AC SR-2831-DC
5
Patent
Save 1 color/mode for each zone

Operation
Description of buttons
Switch:short touch to switch on/off
Zone number
Short touch Z1 Z2 Z3 Z4 to choose the zone
Long touch Z1 Z2 Z3 Z4 to switch on/off
1.Do wiring according to the wiring diargram.
2.Do Learning
a.Wake up the panel by touching ON/OFF button
b.Press at learning key on receiver SR-1009XX
c.Touch any zone button on panel
d.Touch color wheel
e.connected led light flash means successfully learnning.
Safety & Warnings
Warranty Agreement
1) The product shall be installed and serviced by a qualified person.
2) IP20.Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof
enclosure.
3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
4) Please check if the output voltage of any LED power supplies used comply with the working voltage of the
product.
5) Never connect any cables while power is on and always assure correct connections to avoid short circuits
before switching on.
6)
7) For update information please consult your supplier.
Please ensure that the cable is secured tightly in the connector
1) We provide lifelong technical assistance with this product:
5-year warranty. We print date on every products, for example :1125 means year 2011,week 25.The
warranty is for free repair or replacement and covers manufacturing faults only.
For faults beyond the 5-year warranty we reserve the right to charge for time and parts.
2) Limited Warrenty
Any defects caused by wrong operation.
Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and
replacement of chips.
Any damages due to transportation, vibration etc. after purchase.
Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near
harmful chemicals.
Product has been updated
3) Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
Saving color or mode
Color running button:
short touch to start or pause color running
mode;
long touch to adjust speed(10 built-in color
running modes)
Brightness
Square color pad
Short touch to choose the color R.G.B.W
Long touch to dim brightness of R.G.B.W
3.How to delete the learnning ID?
Long press the learnning key over 5 seconds, till the led light flash.
4.How to save color /mode ?
Choose zone
Touch square pad to choose color-(or touch to choose mode )
Touch over 3 seconds until led light flash
Then one color/mode has been successfully saved.
5.How to set master?
To choose a master from slaves by jumper for each zone.
Close circuit for master
Open circuit for slave
Each zone only can set one receiver driver to be master, All others are slaves in same zone.
After a period of time, the master will do synchronization operation to keep same color /mode of all slaves in one
zone.