ARMATURA EP30CF User manual

The EP3XCF series reader is one of the most compact biometric (fingerprint) + Card
readers available that supports fingerprint and over 100 RFID card types and both NFC
and Bluetooth Low Energy credentials. Installs on Flush Mount.
Parts Included
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your device.
Explorer Series - EP30CF/32CF Reader (1pc)
Quick Start Guide (1pc) and Mounting Template (1pc)
Screwdriver (1pc)
Flat-head phillips screws (4pcs) and Anchors (4pcs)
– for mounting directly to a wall (no junction box)
H0.9 Hex Wrench (1pc)
Inner-hexagon screw (4pcs) – for fixing the panel to the reader
Recommended Parts(notsupplied)
Cable
4 conductor Twisted Pair Over-All Shield and UL approved, Belden 3107A or equivalent
(OSDP)
Certified LPS DC power supply
Metal or plastic junction box
Drill with various bits for mounting hardware
Mounting hardware
1Product Overview
4.1 " (105.2mm)3.5 " (89mm)
0.2 " (5mm)
6.2"(157.2mm)
EP30CF
EP32CF
Model: EP30CF / 32CF
Explorer Series
Quick Start Guide www.armatura.us
All Weather Outdoor Multi-tech Smart Reader
Version1.0
The EP3XCF series can communicate with the control panel via RS-485 (OSDP) .
2Reader Connection
Connection via RS-485 (OSDP)
5Frequency Bands And Maximum Output Power
3Using And Testing The Reader
Frequency bands
2402MHz - 2480MHz
125kHz
13.56MHz
Maximum output power
7.08dBm
-24.83dBuA/m@10m
4.21dBuA/m@10m
6Certificate Information
Copyright © 2022 ARMATURA LLC. All rights reserved.
ARMATURA LLC www.armatura.us E-mail:[e-mail]
Power the reader on, the
reader will beep and the
LED's will flash.
Present the virtual card face-on to
the reader until you hear a "beep".
Reader is now working correctly.
Pigtail
Red
Black
Red/Green
Brown
Bare
Green
White
Orange
Pink
Yellow
Violet
Description
+9~24V DC
Ground
RS-485 A
RS-485 B
/
/
/
/
/
/
/
Pigtail version Adapter version
Adapter version wiring：
Fingerprint
Pigtail version wiring：
Card
RS-485 Adapter
Reader
Connecting Line
A
B
A
2.6 " (65.2mm)1.4 " (36.7mm)
0.2
" (5mm)
5.3"(133.7mm)
1
2
3
Waterproof Rubber Ring
Speaker
Terminal Block
LED Indicator
1
Card Reading Area
2
Fingerprint Reader
3
4
5
6
4
5
6
RS-485 Port
+VDC
GND
485
-
485+
Ground
RS-485 B
+9~24V DC
RS-485 A
RS-485 Port
+VDC VIN
GND
485B
485A
GND
485
-
485+
Virtual Card
12:00
Pigtail
Black
Blue
Grey
White
Brown
Description
RS-485 A
RS-485 B
GND
VIN
GND
12:00

7FCC + CE
"Hereby, Armatura LLC declares that this Product is in compliance with the
essential requirements and other relevant provisions of Directive 2014/
53/EU.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to operate
the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
"This equipment complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of
7.87 inches (20cm) between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter."