ARMATURA Explorer Series User manual

EP10C series can communicate with the control panel via either RS-485 or Wiegand
EP10C
Explorer Series
Quick Install Guide
The EP10C reader is one of the most compact multi-frequency RFID readers available
that supports over 100 RFID card types and both NFC and Bluetooth (LowEnergy)
credentials. Installs on narrow surfaces, Single-Gang, European-standard gang box
and Asian standard boxes to fit all kinds of installation environments.
www.armatura.us
Parts Included
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your device.
EP10C Reader (1pc)
Quick Install Guide (1pc)
Mullion Plate (1pc) and Single-Gang Plate (1pc)
Screwdriver(1pc)
Grub screw/Countersunk KA3.6 x40mm self – tapping screws (2pcs) and Anchors (4pcs)
– for mounting directly to a wall (no junction box)
Grub screw/Countersunk M3 x7mm screw (1pc) – for fixing the reader to the mounting
plate
Recommended Parts(notsupplied)
Cable
5-10 conductor (Wiegand)
4 conductor Twisted Pair Over-All Shield and UL approved, Belden 3107A or equivalent
(OSDP)
Certified LPS DC power supply
Metal or plastic junction box
Drill with various bits for mounting hardware
Mounting hardware
CAUTION: Users
can choose to install
the mullion plate or
the gangbox plate
according to actual
needs.
1. Attach the mounting
template sticker to the
wall, and drill holes
according to the
mounting sticker.
2. Fix the mounting plate
on the wall using the
self–tapping screws.
1. Pass the cable of the
reader through the
wiring hole of the
mounting plate.
2. Place the reader into
the mounting plate
until it fits perfectly.
3. Fasten the reader to
the mounting plate
with the provided
screw.
2
3
Mullion Plate Single-Gang Plate
1Mounting the plate
2Attach the reader to the mounting plate
3Reader Connection
4Using and Testing reader
0.93"/23.7mm
3.0"/
76.2mm
4.84" /123.0mm
1.89"/48.0mm
4.52" /114.8mm
0.93"/23.7mm
1
1.75"/44.4mm
4.38" /111.2mm
0.77"/19.5mm
Outdoor Multi-tech Smart Reader
Pigtail
Red
Black
Red/Green
Brown
Bare
Green
White
Orange
Pink
Yellow
Violet
Description
+9~24V DC
Ground
RS-485 A
RS-485 B
Drain
Wiegand Data 0
Wiegand Data1
Green LED Input
Red LED Input
Beep Input
Tamper
1. Connection via Wiegand.
READER1
Ground
+9~24V DC
Wiegand Data 0
Wiegand Data 1
Green LED
Red LED
Beep
Tamper
Power the reader on, the
reader will beep and the
LED's will flash.
Present the card face-on to the
reader until you hear a "beep".
Reader is now working correctly.
Copyright © 2022 ARMATURA LLC. All rights reserved.
ARMATURA LLC www.armatura.us E-mail:[email protected]
2. Connection via RS485.
RS-485 Port
+VDC
GND
485
-
485+
Ground
RS-485 B
+9~24V DC
RS-485 A
Certificate Information

"Hereby, Armatura LLC declares that this Product is in compliance with the essential requirements and other relevant provisions of Directive
2014/53/EU.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
"This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter."
FCC+CE