ART Technology Development DAM-3015D User manual

DAM-3015D
User’s Manual
Beijing ART Technology Development Co., Ltd.

DAM-3015D User’s Manual V6.13
2
DAM-3015D Module
Introduction
Features
16-channel Digital Output Module
¾Digital Output Mode:16-channel TTL
¾Support double watchdogs
¾LED indicate the output state
¾Power Supply: unregulated +10～+30VDC
¾Power Consumption: 0.7W@24VDC
Industrial Design
DAM-3015D was designed to use in industrial environment. It can be installed in standard DIN rail inside
the cabinet. And it can be powered by unregulated 10VDC ~30VDC to meet the various power supplied
source in field. It also withstands ambient temperature up to 60℃and resists the effects of vibration and
mechanical shock.
Wiring & Installation
Power supply requirements: unregulated +10VDC ~ +30 VDC. "+Vs" is a positive, and "GND" is ground.
"DATA +" and "DATA-" connect with "DATA +" and "DATA-"(or "A" and "B") of RS-232/RS-485
transformation module, then connect transformation module with computer, do not hot plug carefully.
The power indicator flashes after wiring is correct, then you can communication with the host computer.

DAM-3015D User’s Manual V6.13
3
According to the label directs color to wiring:
+Vs （R）Red DATA+ （Y）Yellow
GND（B）Black DATA- （G）Green
It can connect with DAM-3212, show as the following:

DAM-3015D User’s Manual V6.13
4
DAM-3015D
Fig. 1 DAM-3015D Drawing
DAM-3015D can be installed in standard DIN rail inside the cabinet, it also can be installed by stacking
mode.
Fig.2 standard DIN installation

DAM-3015D User’s Manual V6.13
5
Fig.3 stack installation
Wiring Application
Reset Connection:
Shorted the INIT * and GND shorted, add +10 ~ +30 VDC between +Vs and GND, power on, the module indicator
quickly flashes three times, power off until the indicator stops flashing, disconnect the INIT * and GND, then reset the
module has been completed.
After reset successfully, the module restore the factory default values:
Module Address: 1
Baud Rate: 9600
TTL Output Connection

DAM-3015D User’s Manual V6.13
6
Operation Interface
Open the DAM-3000 Software, clicking the “COM1” in the system tree of left dialog block

DAM-3015D User’s Manual V6.13
7
Clicking the “Addr: 001 (DAM-3015D)” in the system tree of left dialog block to go to DAM-3015D configuration page.
In this page, user can configure the output channel.
Ddblclicking the “Addr: 001 (DAM-3015D)” in the system tree of left dialog block to get “Module Information” box, in
this box, we can set “Module Addr” and “Baud Rate”.

DAM-3015D User’s Manual V6.13
8
Default Setting
If the module’s address or baud rate is wrong, or forget the last modified value, the module can be reverted to default
settings. Steps: Short-circuit the “INIT*” and “GND” when there is no power; power-on for 3 seconds, power off,
disconnect “INIT*” and “GND”. The module is reverted to the default settings.
Address: 00
Baud Rate :9600bps
Noparity
The serial port default work mode: parity bit: none
data bits: 8
stop bit: 1
Code Configuration Table
Baud Rate Configuration Code Table
Code 00 01 02 03 04 05 06 07
Rate 1200 2400 4800 9600 19200 38400 57600 115200

DAM-3015D User’s Manual V6.13
9
Pin Definition
Pin Name Function
1 OUT13 Digital output 13-ch
2 OUT14 Digital output 14-ch
3 OUT15 Digital output 15-ch
4~8 NC
9 INIT* reset pin, connect with(B)GND, then power-on to reset
10 (Y)DATA+ RS-485 positive
11 (G)DATA- RS-485 negative
12 (R)+Vs DC Power Supply (+),+10~+30VDC
13 (B)GND DC Power Supply (-)
14 OUT0 Digital output 0-ch
15 OUT1 Digital output 1-ch
16 OUT2 Digital output 2-ch
17 OUT3 Digital output 3-ch
18 OUT4 Digital output 4-ch
19 OUT5 Digital output 5-ch
20 OUT6 Digital output t 6-ch
21 OUT7 Digital output 7-ch
22 OUT8 Digital output 8-ch
23 OUT9 Digital output 9-ch
24 OUT10 Digital output 10-ch
25 OUT11 Digital output 11-ch
26 OUT12 Digital output 12-ch