ADTRAN Job Aid+ 1442704PG2 User manual

jobAid
DESCRIPTION
TheSmallForm‐FactorPluggableOC‐12Bidirectional1550/1310
nm(BidirectionalSFP)plugsintoADTRANequipmentdesigned
toacceptSmallForm‐factorPluggables(SFPs).Installedintoan
appropriatehostunit,theBidirectionalSFPprovidesanOC‐12
interfacetothesupportingsystem.
NOTE
Toensurecompatibility,refertothedocumentationprovided
withthehostmodule.
ThefollowingfeaturesaresupportedontheBidirectionalSFP:
SONETOC‐12compatible(622Mb/s),single‐fiberoperation
15kmmaximumopticalspan
CAUTION
!
Duetocompliancecertificationrequirements,onlySFPssupplied
byADTRANaretobeusedwiththehostmodule.ADTRAN
cannotcertifysystemintegritywithotherSFPs.
Small Form-Factor Pluggable OC-12
Bidirectional 1550/1310 nm
SPECIFICATIONS
OpticalSpecifications:
Opticaltransmitlevel:–8dBmto–15dBm
Opticalreceivelevel:–8dBmto–28dBm
TransmitWavelength:1550nm
ReceiveWavelength:1310nm
Opticalbudget:12(±1)dBm
Opticalconnectors:LC
ExtendedEnvironmentalSupport:
Operationaltemperaturerange:–40°Cto+65°C
Storagetemperaturerange:–40°Cto+85°C
Relativehumidityto95%,noncondensing
INSTALLATION
Before installing the equipment, inspect the Bidirectional SFP. If
damage has occurred during shipping, file a claim with the
carrier, and then contact ADTRAN Customer Support. For more
information, refer to the warranty.
Installation Guidelines
The following are guidelines for this installation.
Do not remove the protective end cap from the SFP until the
fiber optic cable is ready to be connected.
Ensure that the manufacturer’s label on the SFP is facing
upward for correct installation.
Installation Steps
ToinstalltheBidirectionalSFPintoanappropriatemodule,
completethefollowingsteps:
1. InserttheBidirectionalSFPintotheSFPcageonthemodule.
2. Ensurethatthemanufacturer’slabelontheSFPisfacing
upwardforcorrectinstallation.
3. SlidetheBidirectionalSFPallthewayintothereceptacle
untilthereisanaudible“click”.
NOTE
ToremovetheSFPfromthecageonthecircuitcard,usethelatch
ontheSFP.
CLEI: S00TALBJ__
Product P/N: 1442704PG2
Issue Date: May 2014
Document P/N: 61442704PG2-22B
Documentation for ADTRAN Carrier Networks products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following documents provide additional information for this product:
SFP/XFP/SFP+ Compatibility Matrix and Engineering Guide

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can
be found online at www.adtran.com/warranty.
©2014 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442704PG2-22B*
SAFETY AND REGULATORY COMPLIANCE
WARNING
!
Read all warnings and cautions before installing or servicing this
equipment.
CAUTION
!
ElectrostaticDischarge(ESD)candamageelectronicmodules.
Whenhandlingmodules,wearanantistaticdischargewrist
straptopreventdamagetoelectroniccomponents.Place
modulesinantistaticpackingmaterialwhentransportingor
storing.Whenworkingonmodules,alwaysplacethemonan
approvedantistaticmatthatiselectricallygrounded.
Thisproductmeetsorexceedsalltheapplicablerequirements
ofNEBS,TelcordiaGR‐63‐CORE,GR‐1089‐CORE,andETSI
EN300368.TheproductisintendedfordeploymentinCentral
Officetypefacilities,EEEs,EECs,andlocationswherethe
NECapplies(forexample,CustomerPremises).Theproductis
tobeinstalledinADTRANproductsinRestrictedAccess
Locationsonly,andinstalledbytrainedservicepersonnel.
ThisdevicecomplieswithPart15oftheFCCrules.Operationis
subjecttothefollowingtwoconditions:
1. Thisdevicemaynotcauseharmfulinterference
2. Thisdevicemustacceptanyinterferencereceived,including
interferencethatmaycauseundesiredoperation.
ChangesormodificationsnotexpresslyapprovedbyADTRAN
couldvoidtheuserʹsauthoritytooperatethisequipment.
CAUTION
!
PerGR‐1089‐COREtheADTRANsystemthattheproductis
beingdeployedinisdesignedandintendedforinstallationas
partofaCommonBondingNetwork(CBN).TheADTRAN
systemthattheproductisbeingdeployedinisnotdesigned
norintendedforinstallationaspartofanIsolatedBonding
Network(IBN).
PerGR‐1089‐CORESection9,theproductdoesnothavean
internalDCconnectionbetweenbatteryreturnandframe
ground.TheproductcanbeinstalledinaDC‐I(isolated)or
DC‐C(common)installation.Forinstallationswhereother
cardsorthehostsystemhaveinternalconnectionsbetween
batteryreturnandframeground,thesystemwouldbe
intendedfordeploymentonlyinaDC‐Cinstallation.
TheADTRANsystemchassisframegroundterminalmustbe
connectedtoareliableearthgroundtoensurethatthemetal
enclosureoftheproductisproperlygroundedviathe
backplaneconnector.
CAUTION
C
ThisproductisaClass1LaserProductandcomplieswiththe
LaserSafetyrequirementsofFDA21CFR1040.11,EN60825‐1,
andEN60825‐2.TheproductisNRTLListedandCBCertifiedto
allapplicableAmericanandEuropeansafetystandards.
NOTE
TheGigabitEthernetport(s)areopticalandthereforearenot
classifiedasanytypeofportasdefinedinAppendixBofGR‐
1089‐CORE.
Theproductisdesignedtomeetthefollowingenvironmental
classes:
ETSIEN300019‐1‐1“Classificationofenvironmental
conditions;Storage,”Class1.2
ETSIEN300019‐1‐2“Classificationofenvironmental
conditions;Transportation,”Class2.3
ETSIEN300019‐1‐3“Classificationofenvironmental
conditions;Stationaryuseatweather‐protectedlocations,”
Class3.3
Theequipmentisdesignedtofunctionwithoutdegradation
duringexposuretoalltestseveritiesperClass3.3.
ThisproductmeetsEURoHSDirective2002/95/ECand/orappli‐
cableexemptions.Refertowww.adtran.comforfurtherinfor‐
mationonRoHS/WEEE.
NOTE
ThisproductiscompliantwithSFF‐8472“DigitalDiagnostics
MonitoringInterfaceforOpticalTransceivers,”Revision9.3.
ThisproductiscompliantwiththeSmallForm‐Factor
Pluggable(SFP)Multi‐SourceAgreement(MSA).
ThisproductisdesignedtobedeployedinGR‐3108‐CORE
environmentalclass1,2,and3,asdefinedinGR‐3108‐CORE.