Artec Mini Tracker 505 User manual

Mini Tracker 505 User Manual

(a) Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that
will corrode electronic circuits. If your device does get wet, remove the battery, and allow the device to
dry completely before replacing it.
(b) Do not use or store the device in dusty, dirty areas. Its moving parts and lectronic components can be
damaged.
(c) Do not store the device in hot areas. High temperatures can shorten the life of electronic devices,
damage batteries, and warp or melt certain plastics.
(d) Do not store the device in cold areas. When the device returns to its normal temperature, moisture can
form inside the device and damage electronic circuit boards.
(e) Do not put Master and Slave at same place in case of this set is unable playing functions to guard your
valued goods.
(f) This product only assists to provide the warning alarm for reminding the user. It does not guarantee to
prevent steal or rob by personal safety and property if any urgent need. This product does not guarantee
any damage of personal safety, property, material or the information loss, or other related loss.
(g) We reserve the right in changing the specification of the hardware and software designs to manuals at
any time and without prior notice. Informationin this document is subject to change without notice.
(h) This product operational temperature is between 0 °C ~ +55 °C. Storage temperature is between -10 °C~
+60 °C.
Warning: Do not put the battery into the fire or heat resource. It will be cause dangerous or even explosion.
(a) Do not attempt to open the device other than instructed in this guide.
(b) Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine
mechanics.
(c) Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
(d) Do not paint the device. Paint can clog the moving parts and prevent proper operation.
Warning
1
Care and Maintenance
Caution

Recycle: The Battery provided in this product should be recycled to protect the local environment.
Please contact with local recycle department for detail.
2
FCC Certifications
Federal Communication Commission Interference Statement
This equipment has been tested and improved to comply with the limits of a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy, if installed and used not in accordance with the instructions, may cause harmful interference to radio
communications. However,there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2)this device must accept an interference received,
including interference that may cause undesired operation.
FCC Caution: Any changes or modifications are not expressly approved by the party responsible for
compliance which could void the user's authority to operate this equipment.
FCC ID Master: WMPM05A01
Slave: WMPS05A01
EU Declaration Conformity
This product is carrying the CE-Mark in accordance with the related European Directives.
Care and Maintenance
(e) The working range, alarm range, searching and detection are depends the terrain environment because
of radio wave efficiency.
(f) If the beeps sound are not loud enough, it may means the battery low. Change new battery for louder
alarm sound.
(g) If you want to apply this product during the flight trip, please comply with the flight safety law according to
each country.

3
Signal indication
Master
Slave
Front
Front
Back
Back
Search button
Signal
indication
Distance
indication
Right direction
Mode switch
Mute
Power on
(Standby)
Power off
(Sleeping)
Buzzer
Battery cover
Left direction
Hanging hole for strap
Mute distance
melody button
at search mode
Hanging hole
for strap
Clip
Overview

0 m 100 m
Search
8~16 m Alarm
Master
Slave Slave
LR 1
2.4GHz ISM2.4GHz ISM
130 × 2
19×28×7.5 mm
8~16m
Alarm
Trident
Direction
Z
ZZ
Z
Sleeping
Mode
Master
39×48×6.8 mm
Frequency
Battery LR 44 × 2
Switch
2 buttons
Size
Slave
ON / OFF / MUTE
Button
4
No
Alarm
Working Method
Specification
Base on open frame condition.
0~80m

Master
1
2
5
The Battery Installment
1
2
3
1
1. Open from the fillister on the
bottom of housing or curve side
by your nail, like open shell.
2. Put 2pcs batteries into.
*** Make sure the installment direction of
positive (+) & negative (-) of battery are
followed up the drawing showed on the
inside of back battery cover.
3. Set back the battery cover.
Slave
1. Press the clip on battery cover then push
backwardly.
2. Put 2pcs batteries into.
*** Make sure the installment direction of
positive (+) & negative (-) of battery are
followed up the drawing showed on battery
cover.
3. Set the battery cover back.

6
Getting Started
For the first time use, please set the battery into Master according to above
battery installment .
Switch to power on
Pull out
Plastic isolation Place two devices no
more than 10 cm apart.
Signal indication
Signal LED ON for
re-linking.
Distance
indication
Beep
Re-link successful!
Master shows the distance
with Slave via LED and
melody (beep).
Press Search button to stop
melody.
12
5
3
4
Beep
If Master can't link with
Slave, it will beep once
every few seconds.
Caution

Search
1 2
Press Search button
2~3 seconds
Start to detect the location
of Slave.
Near Far
7
Correct
holding
Wrong holding
Error indication - whole direction LED goes off but signal LED lights up 3 seconds then
displays new searched distance.
1.) Search from correct direction to wrong direction
2.) Over pass
1.) LED light: more
closer, more lights.
2.) Search melody: more
closer, more rapid.

Search
North
South
East
West
2 Distance LEDs
3 Distance LEDs.
The strongest
signal direction !
Turn to different directions
for signal comparison
One Distance
LED only
2 Distance LEDs
8
1
2
Go the way of the
strongest signal
direction to find out
Slave.

9
321
Search
Mute searching melody from Master. Listen beep sound
from Slave to assist short range searching.
Press & hold the LED
light button
Stop the melody Listen to the beep
sound from Slave
Beep
22

10
Search
3
Stop
searching
Back to Standby mode
Signal LED flashes every
second for re-linking
Signal indication
Press Search button
2~3 seconds
Error indication - whole direction LED goes off but
signal LED lights up 3 seconds then displays new
searched distance.
1.) Search from correct direction to wrong direction
2.) Over pass

East
North
11
North
East
0～80 m
Signal indication
Distance LED goes out all
lights suddenly and only flash
Signal LED with beep sound
LED displays new
searched distance
Go back to original search
direction or location
4
21
3
Location:
North
Go to the
wrong direction
Original searching
(Right direction)
[Suggestion]
3 seconds
later
Searching Example

Alarm
1 2
Beep
Beep
Over 8~16 meter.
Come with beep!
Stop alarm (beep) if both devices
comes within 8 meter again.
Signal
indication
When Slave and Master are over 100
meter or lose signal
Caution
Slave flashes half minute to
wait for re-linking
No linking then into sleeping
modeand stop flash
12

Switch to sleeping mode
13
Sleeping
Under Standby mode Stop signal to Slave
No linking then into sleeping mode and stop flash
Slave flashes half minute to wait for re-linking
2
1
Switch the button to
section 0 (OFF)

14
Switch the button to
section 1 (ON)
Signal LED ON for re-linking
Available for distance within
80 meter
Re-link successful!
Master shows the distance
between Slave via LED
and melody (beep)
Distance
indication
Signal indication
Beep
Beep
1 2
Beep
Can't get signal from Slave.
Signal LED flashes each second & comes with beep.
(Slave maybe out of working range 100 meter, or no power.)
Re-link / Wake up

Mute
Mute (Mute At Search mode, Or No Need The Guard
Service)
12
Switch the button to
section 2 (MUTE)
3
Only Display the distance
indication LED without
searching melody
Under Standby mode
Switch to Mute mode
Press Search button
Under mute mode, the Alarm
function is disabled.
15

Low Battery
If this kit is under low battery stage, it may cause
abnormal display to alarm, beeps or non-working to
confuse actual working stage.
Please change new battery as soon as possible.
16
1 beep sound every 120 seconds continuously.

Suggested setting place
Wrong
holding
Correct
holding
Correct
holding
Wrong
holding
90 < 90
17
*** Do not cover the top side of Master.

18
Master Slave
Suggested setting place
Suggested setting place

91E-02B1-U50G11