Artesyn LGA80D User manual

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 1 of 18
LGA80D
Evaluation Board User Manual

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 2 of 18
TABLE OF CONTENTS
TABLE OF CONTENTS ...................................................................................................................................................2
GENERAL ..........................................................................................................................................................................3
EQUIPMENT REQUIRED ......................................................................................................................................................4
DEFAULT SETTINGS ...........................................................................................................................................................5
COMPONENT IDENTIFICATION.................................................................................................................................6
OPERATION......................................................................................................................................................................7
POWER UP SEQUENCE ........................................................................................................................................................7
ADDITIONAL INFORMATION.............................................................................................................................................11
TEST FUNCTIONS .............................................................................................................................................................13
APPENDIX A –SILK-SCREEN LAYER OF THE EVALUATION BOARD...........................................................16
DOCUMENT REVISION HISTORY.............................................................................................................................17
CONTACT FOR TECHNICAL SUPPORT AND INFORMATION ..........................................................................18
AMERICAS .......................................................................................................................................................................18
ASIA ............................................................................................................................................................................18
EUROPE ...........................................................................................................................................................................18

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 3 of 18
GENERAL
The LGA80D evaluation board allows the user to test and investigate the performance of
the LGA80D non-isolated module.
Within the kit there are the following items:
- The evaluation board equipped with 2 LGA80D modules
- The Artesyn PMBus interface dongle
- The PMBus to USB interface cables
Fig. 1 –LGA80D evaluation kit
This equipment allows you monitor and control the modules via your computer, or you can
apply settings to the modules by hardware configuration.

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 4 of 18
Equipment required
To run the evaluation board, the following equipment will be required to supply power to the
board, apply load to the board, and to cool the dc-dc converters if the board is to be
operated for long periods.
Recommended Test Equipment
DC Source
7~14V, 80A
Load
45A or above for Vo1 or Vo2, 90A or above for Vo3
Cooling Fan
Please use fan cool if operate at full load for long time
Table 1 –Test equipment required
Power cables with M6 ring terminations are required for the input and output connections to
and from the evaluation board.
Test equipment that will be required will be:
- A personal computer with the LGA80D GUI software installed on it
oThe GUI software is available on the Artesyn website
https://www.artesyn.com/power/LGA80D-eval-GUI
oPlease refer to the GUI user manual for instructions on how to install and use
this software
- Oscilloscope and associated test probes
- Digital multi-meter and associated test probes

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 5 of 18
Default settings
The evaluation board has been supplied with the following configuration and set-up by
default.
If no changes are made to the hardware and firmware configuration of the unit then, the
user will see that this board is equipped with 2 LGA80D modules with the following voltage
settings:
- 1 module is configured for a single output
oOutput voltage setting is 1V via the dip switches on the PCB
- 1 module is configured for 2 independent outputs
oOutput A voltage is set to 1V via the dip switches on the PCB
oOutput B voltage is set to 1V via the dip switches on the PCB
The PCB has been equipped with the following value of capacitors. These have been
selected to provide optimum performance under as many different test conditions as
possible, but the user may change or optimize the values according to the specific
conditions that are to be replicated:
- Input capacitance (per module)
- Output capacitance
oIn single O/P configuration
oIn dual O/P configuration

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 6 of 18
COMPONENT IDENTIFICATION
The key components and connection locations are shown in the picture of the evaluation
board below.
Note that the LGA80D shown at the ‘top’ of this picture is the one that is configured as the
single output unit, and the ‘bottom’ converter is configured as a dual output module.
Fig. 2 –LGA80D setup
Assumption: The user has made the power connections to and from the evaluation card.
These will not be described further.

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 7 of 18
OPERATION
Here are the instructions to power up the PCB and modules.
Power up sequence
To power up and configure the evaluation card, please follow the steps as described below.
1. Initial set position of the enable switch
Please make sure the OUTPUT ENABLE toggle switch (S201) is in the “disable”
orientation as shown below with the toggle of the switch leaning toward the modules
and the output side of the PCB (and away from the input side of the board).
Fig. 3 –Initial enable switch orientation

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 8 of 18
2. Connection and configuration
Connect the input and output cables to the M6 terminations of the PCB.
Then connect the following:
a. Connect the Vin1 and Vin2 connections to the DC power source with a voltage
setting in the range of 7.5Vdc to 14Vdc
b. Connect the Vo1, Vo2 and Vo3 connections to your E-load
c. Add the enable jumpers to the En1, EN2 and EN3 locations on J203 –this will
ensure that the 3 outputs will be enabled. Note these are the jumper components
located next to the enable switch –they are shown below.
Fig. 4 –Enable jumper location and population

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 9 of 18
3. Connection of the I2C dongle to I2C connector
This is the interconnect cable between your PMBus dongle and the evaluation PCB.
It is polarized and will only fit into the connected in 1 orientation
The other end of this cable should be plugged into your dongle. The dongle also has
USB connections (and the cable is provided) to connect your dongle to the USB port
of your computer.
Fig. 5 –I2C cable connection to the evaluation board
4. Voltage setting
Select the suitable voltage for Vo1, Vo2 and Vo3 by the voltage selector DIP
switches Vo setting. The silk screen marking shows the voltage settings that can be
achieved by these switches.
Fig. 6 –Nominal output voltage settings by DIP switch setting

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 10 of 18
5. Power up sequence
To enable the DC-DC converters to work now that all connections to and from the
evaluation board have been applied, take the following steps:
a. Apply the input voltage to Vin1 and Vin2
b. Operate the toggle enable switch (S201) so that the toggle is leaning toward the
input connections and away from the output connections.-
The LGA80D modules should now be operating and supplying power to your E-load.
Fig. 7 –Toggle switch position to enable the outputs of the modules
6. The Power down sequence
To disable the outputs from the evaluation board, please take the following steps:
Toggle Enable switch to disable Vout
Turn off main voltage to Vin1 and Vin2
Note that not following power up/down sequence may damage the evaluation board.

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 11 of 18
Additional information
1. Initial set position of the enable switch
This demo board is designed to have two LGA80D modules which can be tested
independently with 2 independent input supplies.
However, if the user wants to use one input (either Vin1 or Vin2) to power both
modules, then this can be done by linking the 2 solder pads together as identified in
the picture below:
Fig. 8 –Shorted pads required to use a single input to supply both LGA80D modules

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 12 of 18
2. Enabling each output
The outputs of the individual converters can be enabled or disabled by populating
and de-populating the enable jumpers as required.
Fig. 9 –The enable jumpers –all 3 shown in place to enable all 3 outputs

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 13 of 18
Test functions
The evaluation board is also equipped with test points to provide easily accessible voltage
measurement points.
1. Vin and Vout sense locations
Accurate input and output voltage measurements via pin-headers can be found on
J205 and J1205.
Use J1205 for monitoring the input voltage and output voltage of the ‘top’ LGA80D
(when the input connections are on the left). Note, this converter is configured for a
single 80A maximum output.
The location of the connector and the location of the connections when viewing the
connector from the top side (component side) is shown below.
Fig. 10 –Voltage sense locations for Vin-2 and Vout-3
Use J205 for monitoring the input voltage and output voltage of the ‘bottom’ LGA80D
(when the input connections are on the left). Note that this converter is configured for
2 independent 40A maximum outputs.
The location of the connector and the location of the connections when viewing the
connector from the top side (component side) is shown below.
Fig. 11 –Voltage sense locations for Vin-1 and Vout-2 and Vout-1

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 14 of 18
2. Ripple and regulation measurement locations
There are 3 test points provided to give accurate measurements of the output noise
and ripple from the LGA80D.
The mating connector to the SMA connector found on the Evaluation board can be
defined as “A Straight Cable Mount SMA Connector, Plug, Crimp Termination type
RG174U”.
J1403 –Point of Measurement for Vout-3 ripple and regulation.
Fig. 12–Ripple measurement point for Vout-3
J303 - Point of Measurement for Vout-2 ripple and regulation
Fig. 13–Ripple measurement point for Vout-2
J403 Point of Measurement for Vout-1 ripple and regulation
Fig. 14–Ripple measurement point for Vout-1

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 15 of 18
3. Output voltage regulation measurement location
To measure the output voltage at the regulation point of the LGA80D units –the
following straight pin header can be used.
Note that Vs3 will be output of the unit configured to be a single-output of up to a
maximum of 80A.
Note that Vs2 will be Vout-2 from the LGA80D configured to be a dual-output unit of
up to 40A maximum.
Fig. 14 –Output voltage regulation measurement point for Vout-3 and Vout-2
Errata: The silk screen on the demo-PCB has an error on J1206, VS1+ and VS1- are
actually VS2+ and VS2- respectively as shown on the right in the figure above.
4. For any other measurements and configurations
Please contact your Artesyn representative or technical support for any further
configurations or evaluation parameters that you wish to investigate.

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 16 of 18
Appendix A –Silk-screen layer of the evaluation board

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 17 of 18
DOCUMENT REVISION HISTORY
REV
DATE
DESCRIPTION
REMARKS
01
8th June 2016
First release

LGA80D Evaluation Board User Manual
Artesyn Embedded Technologies LGA80D Evaluation Board
June 2016
Page 18 of 18
Contact for Technical Support and Information
Americas
Phone:
[phone] or
[phone]
Email:
[email protected]
Availability:
8am to 8pm (EST)
Asia
Phone:
400 8899 130 (in China) and
[phone] (outside China)
Email:
[email protected]
Availability:
8:30am to 5:30pm (HKT)
Europe
Phone:
(0) 8000 321 546 (in the UK) and
[phone] (outside UK)
Email:
[email protected]
Availability:
8am to 5pm (GMT)
Visit us: http://www.artesyn.com/
http://www.artesyn.com/power/
Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are
trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos
referred to are trade names, trademarks, or registered trademarks of their respective owners. ©
2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions,
please visit www.artesyn.com/legal.