Artesyn MVME2500-ECC User manual

MVME2500-ECC
Quick Start Guide
P/N:6806800L02B (August 2014) Observe ESD-safe
measures
What’s in the box?
Install the RTM
When installing or servicing the
module or accessories, strictly
observe the safety precautions
in the Safety Notes Summary.
Otherwise, personal injury or
property damage may occur.
• Use either a properly grounded ESD
wrist strap or make sure that you are
working in an ESD-safe environ-
ment.
• Connect to the ESD connector at the
front or the rear of the system.
Make sure you receive all items of
your shipment:
• One MVME2500-ECC VMEbus
board
• One printed copy of Quick Start
Guide
• One printed copy of Safety Notes
Summary
• Other items that were ordered
Prepare the installation
site
• For information on the environmen-
tal and power requirements, see the
MVME2500-ECC Installation and Use
manual.
• Operating temperatures refer to the
temperature of the air circulating
around the blade and not to the
actual component temperature.
1
2
3
4
1. Power down all equipment and discon-
nect the power cable from the AC
power source.
2. Remove the chassis cover.
3. Remove the filter panel(s) from the card
slot(s) at the rear of the chassis (if the
chassis has a rear card cage).
4. Install the top and bottom edge of the
transition module into the rear guides
of the chassis.
5. Ensure that the levers of the two injec-
tor/ejectors are in the outward posi-
tion.
6. Slide the transition module into the
chassis until resistance is felt.
7. Move the injector/ejector levers in an
inward direction.
8. Verify that the transition module is
properly seated and secure it to the
chassis using the two screws adjacent
to the injector/ejector levers.
9. Connect the cables to the transition
module.

MVME2500-ECC-Quick Start Guide
Artesyn Embedded Technologies
Marketing Communications
2900 S. Diablo Way, Suite 190
Tempe, Arizona 85282
Artesyn Embedded Technologies
Lilienthalstr. 17-19
85579 Neubiberg/Munich
Germany
Finding more information
For more information on the product, see
the MVME2500-ECC Installation and Use and
other related documentation.
Visit our Web site http://www.arte-
syn.com/computing. Use SUPPORT>TECH-
NICAL DOCUMENTATION link to look for
technical documentation.
Technical Assistance
To request technical assistance, visit our
Web site http://www.artesyn.com
Install the board6
1. Attach an ESD strap to your wrist. Attach
the other end of the strap to an electrical
ground. Make sure that it is securely fas-
tened throughout the procedure
2. Remove VME filler panels from the VME
enclosures, as appropriate.
3. Install the top and bottom edge of the
board into the guides of the chassis.
4. Ensure that the levers of the two injector/
ejectors are in the outward position.
5. Slide the board into the chassis until
there is resistance.
6. Simultaneously move the injector/ejec-
tor levers in an inward direction.
7. Verify that the board is properly seated
and secure it to the chassis using the two
screws located adjacent to the injector/
ejector levers.
8. Connect the appropriate cables to the
board.
9. To remove the board from the chassis,
reverse the procedure and press the red
locking tabs (IEEE handles only) to
extract the board.
Install the PMC/XMC
support
5
1. Remove the PMC/XMC filler plate from
the front panel cut-out.
2. Slide the front bezel of the PMC/XMC into
the cut-out from behind. The front bezel
of the PMC/XMC module will be flushed
with the board when the connectors on
the module align with the mating con-
nectors on the board.
3. Align the mating connectors properly
and apply minimal pressure to the PMC/
XMC until it is seated to the board.
4. Insert the four PMC/XMC mounting
screws through the mounting holes on
the bottom side of the board, and then
thread the four mount points on the
PMC/XMC. Tighten the screws.
5. Install the board into the appropriate
card slot. Make sure that the board is well
seated into the backplane connectors.
Do not damage or bend connector pins.
6. Replace the chassis or system cover.
7. Reconnect the system to the power
source and then turn on the system.
The MVME2500-ECC does not support hot
swap. Power off the slot or the system and
make sure that the serial ports and switches
are properly configured.