ARTEX C406-2 Series Instruction Manual

Page 1 of 66
MAY 28/2020
570-5000 Rev. U
Initial Issue JUN 30/1999
ARTEX PRODUCTS / ACR ELECTRONICS, INC.
5757 Ravenswood Rd, Ft. Lauderdale, FL 33312
Cage Code: 18560
25-62-11
C406-2 Series
Emergency Locator Transmitter
Description, Operation, Installation and Maintenance Manual
This manual includes data for the equipment that follows:
Component Part No. Model No.
Emergency Locator Transmitter 453-5000 C406-2
Emergency Locator Transmitter 453-5001 C406-2HM

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 2 of 66
NOTICES
THE INFORMATION CONTAINED HEREIN IS NOT PROPRIETARY.
Information in this manual is subject to change without notice. ACR Electronics makes no warranty,
expressed or implied, with regard to this manual, including but not limited to any implied warranties of
merchantability, fitness for a particular purpose, and non-infringement. In addition, ACR Electronics makes no
warranty with regard to the documentation or data contained herein. ACR Electronics is not liable in the event
of incidentals, special, consequential, or any other damages in connection with or arising from furnishing,
performance, or use of this manual.
For further information contact Sales, ACR Electronics, 5757 Ravenswood Rd, Fort Lauderdale, FL 33312.
Telephone [phone].
AIRWORTHINESS LIMITATIONS
The Airworthiness limitations section is FAA approved and specifies inspections and other maintenance
required under 14 CFR§ 43.16 and 91.403, unless an alternative program has been approved.
IMPORTANT NOTICE
ACR Electronics will be responsible for full distribution and revisions of ICA’s (Instructions for Continued
Airworthiness). For inquiries regarding the content and currency of this manual, contact ACR Electronics,
5757 Ravenswood Rd, Fort Lauderdale, FL 33312. Telephone [phone].

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 3 of 66
RECORD OF REVISIONS
REVISION
CHANGE
DATE
REVISION
CHANGE
DATE
-
RELEASE
Jun 30/1999
L
ECO 16044
Jun 19/2015
-
ECO 1493
Sep 07/2000
M
ECO 16887
Mar 30/2018
-
ECO 1523
Oct 18/2000
N
ECO 17024
Feb 28/2019
A
DCN 1641
Apr 11/2001
P
ECO 17212
Feb 7/2020
A
DCN 1760
Aug 01/2001
R
ECO 17261
Apr 7/2020
A
DCN 1965
Apr 04/2002
U
ECO 17300
May 28/2020
A
DCN 2115
Dec 10/2002
A
DCN 2356
Feb 11/2004
A
DCN 2527
Jan 20/2005
A
DCN 2689
Jan 09/2006
A
DCN 2888
Nov 26/2006
B
DCN 2968
Mar 20/2007
B
DCN 3174
Feb 26/2008
B
DCN 3282
Aug 25/2008
C
DCA W9414
Apr 06/2010
D
ECO 14756
Jul 27/2011
E
ECO 15149
Jul 31/2012
F
ECO 15177
Aug 28/2012
G
ECO 15410
Jun 20/2013
H
ECO 15726
Aug 13/2014
J
ECO 15723
Aug 27/2014
K
ECO 15830
Dec 01/2014

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 4 of 66
SERVICE BULLETIN LIST
SERVICE
BULLETIN NO
ISSUE
DATE
SUBJECT
MANUAL
REV NO
MANUAL
REV DATE

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 5 of 66
LIST OF EFFECTIVE PAGES
SUBJECT
PAGE
DATE
SUBJECT
PAGE
DATE
Title Page
1
May 28/20
Test and Fault Isolation (cont.)
34
May 28/20
Notices
2
May 28/20
35
May 28/20
Record of Revisions
3
May 28/20
Removal
36
May 28/20
Service Bulletin List
4
May 28/20
37
May 28/20
List of Effective Pages
5
May 28/20
38
May 28/20
Table of Contents
6
May 28/20
Installation
39
May 28/20
7
May 28/20
40
May 28/20
8
May 28/20
41
May 28/20
List of Figures
9
May 28/20
42
May 28/20
Introduction
10
May 28/20
43
May 28/20
11
May 28/20
44
May 28/20
12
May 28/20
45
May 28/20
13
May 28/20
46
May 28/20
14
May 28/20
47
May 28/20
15
May 28/20
48
May 28/20
16
May 28/20
49
May 28/20
Description and Operation
17
May 28/20
50
May 28/20
18
May 28/20
51
May 28/20
19
May 28/20
52
May 28/20
20
May 28/20
53
May 28/20
21
May 28/20
54
May 28/20
22
May 28/20
55
May 28/20
23
May 28/20
56
May 28/20
24
May 28/20
57
May 28/20
Test and Fault Isolation
25
May 28/20
58
May 28/20
26
May 28/20
Appendix A
59
May 28/20
27
May 28/20
60
May 28/20
28
May 28/20
Illustrated Parts List
61
May 28/20
29
May 28/20
62
May 28/20
30
May 28/20
63
May 28/20
31
May 28/20
64
May 28/20
32
May 28/20
65
May 28/20
33
May 28/20
66
May 28/20

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 6 of 66
TABLE OF CONTENTS
RECORD OF REVISIONS ............................................................................................................................3
SERVICE BULLETIN LIST ...........................................................................................................................4
LIST OF EFFECTIVE PAGES........................................................................................................................5
TABLE OF CONTENTS ...............................................................................................................................6
LIST OF FIGURES .....................................................................................................................................9
INTRODUCTION .....................................................................................................................................10
1. Manual Usage ..............................................................................................................................10
A. General ...............................................................................................................................10
B. Application .......................................................................................................................... 10
2. Model Descriptions .......................................................................................................................11
A. C406-2 ................................................................................................................................11
B. C406-2HM ........................................................................................................................... 11
3. Approvals ....................................................................................................................................11
A. C406-2 and C406-2HM ......................................................................................................... 11
B. Battery ................................................................................................................................ 12
C. RTCA DO-160D Compliance .................................................................................................. 12
4. Frequency Allocations...................................................................................................................13
A. Application .......................................................................................................................... 13
B. Discussion ........................................................................................................................... 13
5. List of Acronyms, Abbreviations, and Definitions ............................................................................13
6. References ..................................................................................................................................15
A. Regulatory Documents .........................................................................................................15
B. Other Documents................................................................................................................. 16
DESCRIPTION AND OPERATION .............................................................................................................. 17
1. Description ..................................................................................................................................17
A. Functional Overview ............................................................................................................. 17
B. Components ........................................................................................................................18
2. Operation ....................................................................................................................................20
A. Operational Overview ...........................................................................................................20
B. Normal Operation ................................................................................................................21
C. Manual Activation................................................................................................................. 21
D. ELT Reset............................................................................................................................21
E. Functional Check..................................................................................................................21
3. Specifications...............................................................................................................................22
A. Environmental and Physical ..................................................................................................22
B. Electrical ............................................................................................................................. 23
C. Antennas.............................................................................................................................24
TEST AND FAULT ISOLATION .................................................................................................................. 25
1. Inspection and Test Regulatory Requirements ...............................................................................25
A. United States ....................................................................................................................... 25
B. Canada................................................................................................................................25
C. Other Countries ...................................................................................................................25
2. Inspection and Test Procedures ....................................................................................................26
A. Checklist.............................................................................................................................. 26
B. Preparation..........................................................................................................................26

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 7 of 66
C. Coax Cables and Wiring Connections Inspection –Item 1.......................................................27
D. Mounting Tray and Hardware Inspection –Item 2 .................................................................27
E. Battery Pack Inspection –Item 3 ..........................................................................................27
F. G-Switch Functional Check –Item 4a .................................................................................... 27
G. G-Switch Functional Check (Helicopter Models Only)–Item 4b................................................28
H. Performance Testing Setup................................................................................................... 29
I. 121.5 MHz Frequency Measurement –Item 5a ......................................................................29
J. Audio Modulation Check –Item 5b........................................................................................29
K. 121.5/243.0 MHz Power Output Measurement –Item 5c........................................................30
L. 406 MHz Frequency Measurement –Item 5d .........................................................................30
M. 406 MHz Power Output Measurement –Item 5e ....................................................................30
N. Current Draw Test –Item 5f.................................................................................................31
O. Digital Message Verification –Item 5g...................................................................................32
P. ELT Reset Check –Item 5h ..................................................................................................32
Q. Installed Transmitter Test –Item 6 ....................................................................................... 33
R. Antenna Test –Item 7 .........................................................................................................33
S. Inspection and Test Documentation –Item 8 ........................................................................33
3. Fault Isolation..............................................................................................................................34
A. Self-Test Error Troubleshooting Guidelines ............................................................................ 34
B. ELT Troubleshooting Guidelines ............................................................................................35
REMOVAL ............................................................................................................................................... 36
1. ELT .............................................................................................................................................36
A. ELT Removal .......................................................................................................................36
2. Battery ........................................................................................................................................37
A. Battery Pack Removal ..........................................................................................................37
3. Material or Equipment Return .......................................................................................................38
A. Shipment Information ..........................................................................................................38
B. Return Material Authorization................................................................................................38
INSTALLATION ....................................................................................................................................... 39
1. Regulatory Requirements and Guidelines .......................................................................................39
A. For US Registered aircraft: ...................................................................................................39
B. TSO C126, Paragraph D ....................................................................................................... 39
C. FAA..................................................................................................................................... 39
D. Canada................................................................................................................................39
E. Other Countries ...................................................................................................................40
F. RTCA...................................................................................................................................40
2. Mounting Tray .............................................................................................................................41
A. Location .............................................................................................................................. 41
B. Installation .......................................................................................................................... 42
3. Antenna ......................................................................................................................................42
A. Selection .............................................................................................................................42
B. Location .............................................................................................................................. 43
C. Installation .......................................................................................................................... 43
4. Remote Switch.............................................................................................................................46
A. Location .............................................................................................................................. 46
B. Installation .......................................................................................................................... 47
5. Buzzer.........................................................................................................................................47
A. Location .............................................................................................................................. 47
B. Installation .......................................................................................................................... 47
6. Wiring .........................................................................................................................................48

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 8 of 66
A. General Considerations and Recommendations ......................................................................48
B. Remote Switch Harness Fabrication....................................................................................... 49
C. ELT 12-Pin Receptacle Installation ........................................................................................ 51
D. Cockpit Remote Switch 9-Pin Plug Installation........................................................................52
E. Wiring Installation................................................................................................................52
F. Antenna Connections ...........................................................................................................52
G. Cockpit Remote Switch Power Connection ............................................................................. 52
H. Remote Switch Alternate Power Source .................................................................................52
I. Airframe Ground Connections ...............................................................................................53
J. Buzzer Connections ..............................................................................................................53
K. Remote Switch Final Installation ........................................................................................... 53
7. ELT Installation............................................................................................................................53
A. Installation and Test ............................................................................................................53
B. Harness ELT Receptacle Sealing............................................................................................54
C. Installation Documentation ...................................................................................................55
8. Battery Pack Installation...............................................................................................................55
A. Battery Reinstallation ........................................................................................................... 55
B. New Battery Installation .......................................................................................................56
9. Helicopter Installations - Special Considerations.............................................................................57
A. Background .........................................................................................................................57
B. Recommendations................................................................................................................57
C. Orientation .......................................................................................................................... 58
APPENDIX A –ELT REGISTRATION.......................................................................................................... 59
1. Background Information ...............................................................................................................59
A. Hex ID Code ........................................................................................................................ 59
B. Reason for Registration ........................................................................................................ 59
C. Registration Information Resources.......................................................................................59
2. Registration .................................................................................................................................59
A. Responsibility.......................................................................................................................59
B. Required Information ...........................................................................................................59
C. Where to Register ................................................................................................................ 60
ILLUSTRATED PARTS LIST ...................................................................................................................... 61
1. Introduction.................................................................................................................................61
A. Purpose...............................................................................................................................61
B. IPL Usage Guide ..................................................................................................................61
2. Manufacturer Name and Address ..................................................................................................61
A. Ordering Information ...........................................................................................................61
3. Explanation of Detailed Parts List Entries .......................................................................................62
A. Fig # & Item Column ...........................................................................................................62
B. Part # Column .....................................................................................................................62
C. Nomenclature Column ..........................................................................................................62
D. UPA (Units Per Assembly) Column......................................................................................... 63
4. Detailed Parts List ........................................................................................................................64

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 9 of 66
LIST OF FIGURES
Figure 1 ELT Orthogonal Axes...........................................................................................................11
Figure 2 C406-2 Series ELT and Mounting Frame Assembly ................................................................18
Figure 3 Remote Switch Front View................................................................................................... 18
Figure 4 Buzzer................................................................................................................................ 19
Figure 5 Battery Pack Assembly ........................................................................................................19
Figure 6 Antennas............................................................................................................................19
Figure 7 ELT Operational Flow Diagram.............................................................................................20
Figure 8 ELT Orthogonal Axes...........................................................................................................28
Figure 9 Performance Testing Equipment Setup .................................................................................29
Figure 10 Current Draw Test Setup ...................................................................................................31
Figure 11 Short and Long 406 MHz Message Examples....................................................................... 32
Figure 12 ELT Removal Sequence .....................................................................................................36
Figure 13 Battery Pack Removal........................................................................................................37
Figure 14 C406-2 Series ELT Outline and Dimensions ......................................................................... 41
Figure 15 Typical Mounting Tray Installation......................................................................................42
Figure 16 Rod Antenna 110-320 and Blade Antenna 110-328-01 Outlines and Dimensions ...................44
Figure 17 Blade Antennas 110-333 and 110-337 Outlines and Dimensions...........................................45
Figure 18 Blade Antenna 110-337-11 Outline and Dimensions ............................................................46
Figure 19 Remote Switch Outline and Dimensions..............................................................................46
Figure 20 Buzzer Outline and Dimensions ..........................................................................................47
Figure 21 Remote Switch Harness Arrangement.................................................................................49
Figure 22 Remote Switch Harness Wiring Diagram .............................................................................50
Figure 23 Remote Harness Wiring at ELT End .................................................................................... 51
Figure 24 ELT Installation Sequence..................................................................................................53
Figure 25 Battery Pack Installation .................................................................................................... 55
Figure 26 Battery Pack Retaining Screw Tightening Pattern ................................................................ 56
Figure 27 ELT Orthogonal Axes.........................................................................................................57
Figure 28 Orientation of ELT for Helicopter Installations ..................................................................... 58
Figure 29 C406-2 Series ELT Main Assembly and Installation ..............................................................64
Figure 30 Electrical Components .......................................................................................................65
Figure 31 Antennas ..........................................................................................................................66

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 10 of 66
INTRODUCTION
TASK 25-62-11-990-801
1. Manual Usage
SUBTASK 25-62-11-990-001
A. General
1) This manual describes the operation, installation, and maintenance of the Model C406-2 Series
emergency locator transmitter (ELT). This information is provided to ensure initial and continued
airworthiness. Information presented in this manual is accurate at time of printing, but is subject to
change. Refer to the Artex products web site at www.acrartex.com for the latest information and any
updates to this manual.
2) Information on COSPAS-SARSAT emergency locator beacon registration requirements and procedures
is provided in Appendix A –ELT Registration on page 59.
3) Web links provided in this manual were accurate at time of printing but may be subject to change.
4) ACR Electronics reserves the right to add approved components to the ELT system; including, but not
limited to antennas, remote switches, and coaxial cables.
5) Regulatory references contained herein are generally confined to United States and Canadian
requirements and, in any case, should not be considered all encompassing. Consult your national
aviation authority for applicable requirements.
SUBTASK 25-62-11-990-002
B. Application
1) This manual constitutes supporting data/documentation for the C406-2 Series ELT, including:
a) Description and Operation
b) Test and Fault Isolation (includes inspection criteria)
c) Removal
d) Installation
e) Registration
f) Illustrated Parts List
2) In the United States, the C406-2 Series ELT must be installed and maintained in accordance with the
requirements herein and 14 CFR, FAR Parts 43, and 91; and other airworthiness requirements, as
applicable.
3) In Canada, the C406-2 Series ELT must be installed and maintained in accordance with the
requirements herein and Canadian Aviation Regulations (CAR), Part V, Paragraph 551.104 and other
CAR airworthiness requirements, as applicable.
4) C406-2 Series ELT installation and maintenance in all other countries must comply with the
requirements herein and applicable national airworthiness requirements.
5) The accessories (i.e., remote switch and antennas) addressed in this manual are the accessories
most commonly associated with the C406-2 Series ELT. Other options, such as a different remote
switch configuration or an ELT/NAV Interface, should be installed and maintained in accordance with
the written instructions specific to the accessory.
NOTE: Contact ACR Electronics for optional accessories approved for use with a C406-2
Series ELT.
6) To ensure proper operation, only parts listed in the Illustrated Parts List of this manual or those
recommended by ACR Electronics may be used as replacement parts for the C406-2 Series ELT.

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 11 of 66
TASK 25-62-11-990-802
2. Model Descriptions
SUBTASK 25-62-11-990-001
A. C406-2
1) The C406-2 is a type AF (Automatic Fixed) ELT, which transmits on 121.5, 243.0, and 406 MHz.
2) The ELT is enclosed within a multi-piece mounting frame consisting of a mounting tray, protective
top cover and mounting frame cap.
3) When ordered as a system, an installation kit, cockpit remote switch, coax cables, audible buzzer,
and dual input antenna are provided.
SUBTASK 25-62-11-990-002
B. C406-2HM
1) The C406-2HM ELT was developed for helicopter installations and features an additional 5-axis G-
Switch module, which allows the ELT to be activated in any of six axes. See Figure 1.
2) The C406-2HM ELT is identical to the C406-2 ELT in all other aspects.
Figure 1 ELT Orthogonal Axes
TASK 25-62-11-990-803
3. Approvals
SUBTASK 25-62-11-990-001
A. C406-2 and C406-2HM
1) FAA TSO C126, Type AF
a) The conditions and tests required for TSO approval of this article are minimum performance
standards. It is the responsibility of those installing this article either on or within a specific type
or class of aircraft to determine that the aircraft installation conditions are within TSO standards.
TSO articles must have separate approval for installation in an aircraft. The article may be
installed only if performed under 14 CFR Part 43 or the applicable airworthiness requirements.
2) Transport Canada - Type Certificate Data Sheet AP-47 Issue 2
3) Industry Canada - Certification Number 1215873110AF
4) JTSO-2C126
5) ETSO EASA.IM.21O.10040703
6) See ACR’s website at www.acrartex.com for current Cospas-Sarsat Type Approval Certificate and
other approval information.

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 12 of 66
SUBTASK 25-62-11-990-002
B. Battery
CAUTION: LITHIUM BATTERY SAFETY CONCERNS INCLUDE THE POSSIBILITY OF FIRE,
VENTING VIOLENTLY, AND VENTING OF TOXIC GASES.
1) The lithium battery pack used on the C406-2 Series ELT is certified under TSO C142.
a) The conditions and tests required for TSO approval of this battery are minimum performance
standards. It is the responsibility of those desiring to install this battery in a specific type or class
of aircraft to determine that the aircraft installation conditions are within the TSO standards. The
battery may be installed only if further evaluation by applicant documents an acceptable
installation and is approved by the Administrator.
SUBTASK 25-62-11-990-003
C. RTCA DO-160D Compliance
1) DO-160D Environmental Categories: C1-BA204XR2828XZAZZ204B28X
2) The DO-160D environmental categories breakdown is detailed in Table 1.
CATEGORY
SECTION
DESCRIPTION
C1
4.0
Temperature/Altitude
-
4.5.4
In-Flight Loss of Cooling
B
5.0
Temperature Variation
A
6.0
Humidity
204
7.0/8.0
Operational Shock and Crash Safety/Vibration
X
9.0
Explosion
R
10.0
Waterproofness
X
11.0
Fluids Susceptibility
X
12.0
Sand and Dust
X
13.0
Fungus
X
14.0
Salt Spray
X
15.0
Magnetic Effect
Z
16.0
Power Input
A
17.0
Voltage Spike
Z
18.0
Audio Frequency Susceptibility
Z
19.0
Induced Signal Susceptibility
204
20.0
Radio Frequency Susceptibility
B
21.0
Emission of RF Energy
X
22.0
Lightning
X
23.0
Lightning Direct Effects
X
24.0
Icing
Table 1 Environmental Categories Breakdown

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 13 of 66
TASK 25-62-11-990-804
4. Frequency Allocations
SUBTASK 25-62-11-990-001
A. Application
1) This section addresses the 406.0-406.1 MHz transmitter window and the specific frequency band
allocations residing above 406.025 MHz, beginning with 406.028 MHz, which are assigned or reserved
within the 406.0-406.1 MHz distress frequency window.
SUBTASK 25-62-11-990-002
B. Discussion
1) The 406 MHz transmitter frequency of the C406-2 Series ELT was originally 406.025 MHz. In order to
comply with COSPAS-SARSAT frequency allocation requirements, changes to the 406 MHz frequency
may occur since the original release of this product.
2) While the original C406-2 Series ELTs covered by this manual transmit on 406.025 MHz, current
C406-2 Series ELTs may not. The product identification label on each ELT specifies the transmitting
frequencies of the individual ELT. The 406 MHz component may be 406.025, 406.028, 406.037 MHz,
etc. Allocation of frequencies, based on beacon population per specified frequency band, is controlled
by COSPAS-SARSAT.
3) The frequency references throughout this manual for the 406 MHz component should be considered
the baseline and the specific frequency indicated on the ELT product label should be substituted if it
differs from 406.025 MHz.
TASK 25-62-11-990-805
5. List of Acronyms, Abbreviations, and Definitions
SUBTASK 25-62-11-990-001
Term Definition
AC Advisory Circular –A Federal Aviation Administration (USA) bulletin with special
information. For the purposes of this document, the acronym AC does not refer
to electrical alternating current.
AWG American Wire Gauge –An electrical wire diameter standard. Look for this
acronym in front of or following a wire size number.
BNC CONNECTOR A very common type of coax cable connector having a 50 impedance and used
for RF signal connections.
CAR Canadian Aviation Regulations –The rules and regulations governing the
manufacture, certification, operation, maintenance, and alteration of aircraft in
Canada.
CFR Code of Federal Regulations –The general and permanent rules published in
the Federal Register by the executive departments and agencies of the Federal
Government. Title 14, “Aeronautics and Space” contains the FARs.
CONTAINER The term “Container”, within the context of this document, refers to a device
designed to suppress RF signals, such that the broadcast of an ELT placed in
the container cannot reach the SAR satellite system.
COSPAS-SARSAT The international search and rescue consortium that governs the international
satellite-based search and rescue distress alert detection and information
distribution system. For a complete description go to the official web site for the
International COSPAS-SARSAT Program.

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 14 of 66
DER Designated Engineering Representative –An individual qualified and designated
by the FAA to approve, or recommend approval, of technical data to the FAA.
DRIP LOOP Extra wire length used to form a U-shaped bend in a wire or cable. Water or
other fluids will flow down to the bottom of the loop and drip off. Electrical
connections are made at the top of the loop.
ELT Emergency Locator Transmitter –ELTs are installed on aircraft and used to send
emergency signals to the SAR satellite system. The word “Beacon” is associated
with these devices.
EMI Electromagnetic Interference –An undesirable disturbance that affects an
electrical circuit due to either electromagnetic conduction or electromagnetic
radiation emitted from an external source. Also called radio frequency
interference or RFI.
EUROCAE European Organization for Civil Aviation Equipment –EUROCAE documents are
widely referenced as a means of compliance to European Technical Standard
Orders (ETSOs) and other regulatory documents.
FAA Federal Aviation Administration –The United States government agency for
aircraft safety and regulation.
FAR Federal Aviation Regulations –The rules and regulations governing the
manufacture, certification, operation, maintenance, repair, and alteration of
aircraft in the United States.
FORM 337 FAA Form 337 is required anytime a major repair and/or major alteration is
performed on an aircraft. Refer to FAR, Part 43, Appendix A and the definitions
of Major Repair/Alteration contained in FAR, Part 1 for guidance.
FSDO Flight Standards District Office –FAA district offices responsible for aircraft
certification, operation, maintenance, and modification issues, approvals and
enforcement.
G-SWITCH A velocity switch that detects sudden de-acceleration and is used to
automatically activate an ELT. May also be referred to as a “crash sensor”.
LED Light Emitting Diode –Semiconductor device that emits light when current is
passed through it. Usually used as a status or warning indicator.
MIL The three-letter acronym that stands for “Military” and proceeds military
specifications and standards numbers (e.g., MIL-W-2828 would indicate a wire
specification and MIL-STD-2828 would indicate a standard).
P/N Part Number –Refers to a ACR Electronics part number, unless other- wise
noted. Part numbers are also indicated with parentheses (e.g., 28X-2828).
PLUG The term “Plug”, within the context of this document, refers to the male half of
an electrical connector.
RECEPTACLE The term “Receptacle”, within the context of this document, refers to the female
half of an electrical connector.
RF Radio Frequency –The range of electromagnetic radiation that constitutes the
radio spectrum and corresponds to the frequency of alternating current
electrical signals used to produce and detect radio waves.
RTCA Radio Technical Commission for Aeronautics –Organization that makes
recommendations for airworthiness. Refer to http://
www.rtca.org/aboutrtca.asp for more information.
RTV A rubbery silicon-based adhesive typically used to prevent vibration problems
and water intrusion.
SAR Search and Rescue

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 15 of 66
SCREEN ROOM The term “Screen Room”, within the context of this document, refers to a room
designed to suppress RF signals, such that the broadcast of an ELT placed in
the screen room cannot reach the SAR satellite system.
SERVICE LOOP A length of wire or cable, at the connection point, of sufficient length to allow a
component to be withdrawn from its mounting position and disconnected from
its associated wiring.
TETHER A tether is a cord or similar device that anchors something movable to a
stationary point or anchors two items together, such that they cannot become
separated beyond the length of the tether.
TNC CONNECTOR A threaded version of a BNC connector.
TPS CONNECTOR A small, rugged, three-pin bayonet locking connector designed for use when
space and weight limitations are of primary concern.
TSO Technical Standard Order –A TSO is a minimum performance standard issued
by the FAA for specified materials, parts, processes, and appliances used on civil
aircraft.
UTC Coordinated Universal Time –A time standard based on International Atomic
Time. UTC is the time system used in aviation and is often associated with
Greenwich Mean Time (GMT) and/or “Zulu” time.
VHF Very High Frequency –The 30 MHz to 300 MHz radio frequency band.
VSWR Voltage Standing Wave Ratio –Electrical signals will “echo” back on a wire if
load impedance is not matched to the impedance of the wire. VSWR is a
measurement of the amount of voltage being “echoed,” compared to the
original signal.
TASK 25-62-11-990-806
6. References
SUBTASK 25-62-11-990-001
A. Regulatory Documents
1) The following regulatory documents are referred to herein. When referring to such documents, it is
the manual user’s responsibility to ensure they are using the latest revision or release of such
documents. To that end, the revision designator of specific document numbers has not been
included, with the exception of the RTCA document listing, which reflects the revision level of the
documents at the time of TSO testing and certification.
2) Except in the case of a printed manual, reference documents available on-line or source locations are
linked to applicable web sites.
3) United States
a) AC 43-9, “Maintenance Records”
b) AC 43-210, “Standardized Procedures for Requesting Field Approval of Data, Major Alterations,
and Repairs”
c) AC 43.9-1, “Instructions for Completion of FAA Form 337”
d) AC 43-13-1, “Acceptable Methods, Techniques, and Practices –Aircraft Inspection and Repair”
e) AC 43.13-2, “Acceptable Methods, Techniques, and Practices - Aircraft Alterations”
f) FAR, Part 43, “Maintenance, Preventive Maintenance, Rebuilding, and Alteration”
g) FAR, Part 91, “General Operating and Flight Rules”
4) Canada
a) CAR, Part V, “Airworthiness”

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 16 of 66
b) CAR, Part VI, “General Operating and Flight Rules”
5) COSPAS-SARSAT
a) C/S G.005, “Cospas-Sarsat Guidelines on 406 MHz Beacon Coding, Registration and Type
Approval”
b) C/S S.007, “Handbook of Beacon Regulations”
6) RTCA –The following documents are available for purchase at RTCA’s web site www.rtca.org, or by
mail:
a) DO-160D, “Environmental Conditions and Test Procedures for Airborne Equipment”
b) DO-178B, “Software Considerations in Airborne Systems and Equipment Certification”
c) DO-182, “Emergency Locator Transmitter (ELT) Equipment Installation and Performance”
d) DO-183, “Minimal Operational Performance Standards for Emergency Locator Transmitters -
Automatic Fixed-ELT (AF), Automatic Portable-ELT (AP), Automatic Deployable-ELT (AD),
Survival-ELT (S) Operating on 121.5 and 243.0 MHz”
e) DO-204, “Minimal Operational Performance Standards for 406 MHz Emergency Locator
Transmitters (ELT)”
SUBTASK 25-62-11-990-002
B. Other Documents
1) The following documents are available on-line at the Artex products web site at www.acrartex.com or
from ACR Electronics upon request.
a) 570-1000, “ELT Test Set (ETS) Operation Manual”
b) 570-4602, “ELT/NAV Interface Description, Operation, Installation and Maintenance Manual”

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 17 of 66
DESCRIPTION AND OPERATION
TASK 25-62-11-870-801
1. Description
SUBTASK 25-62-11-870-001
A. Functional Overview
1) The ELT automatically activates during a crash and transmits the standard sweep tone on 121.5 and
243.0 MHz. Approximately every 50 seconds, for up to 520 milliseconds (long message protocol), the
406 MHz transmitter turns on. During that time, an encoded digital message is sent to the COSPAS-
SARSAT Search and Rescue (SAR) satellite system.
2) The information contained in the message includes:
a) Serial number assigned to the ELT by the beacon manufacturer or the national beacon
registration authority, or
b) Aircraft identification or registration number, and
c) Country of registration and country code; plus
d) Position coordinates, when coupled with an ELT/NAV Interface (453-6500). Refer to the ELT/NAV
Interface Abbreviated Component Maintenance Manual (570-4602) for a detailed discussion of
the interaction between the ELT, ELT/NAV Interface, and aircraft navigation system.
3) The 406 MHz transmitter will operate for 24 hours and then shuts down automatically. The
121.5/243.0 transmitter will continue to operate until the batteries are exhausted, which is at least 50
hours.
4) The 406 MHz transmitter produces a much more accurate position, typically 3 kilometers as
compared with 15 to 20 kilometers for 121.5/243.0 MHz transmitters. When coupled to the aircraft
navigation system via the ELT/NAV Interface, the accuracy improves to approximately 100 meters.
5) The ELT transmits a digital message that allows search and rescue authorities to contact the
owner/operator of the aircraft through information contained in a database. Information contained in
the database includes:
a) Type of aircraft and aircraft registration number,
b) Owner address and telephone number, and
c) Alternate emergency contact.
6) After the ELT is activated and the 406 MHz signal is detected by the SAR satellite system and a
position is calculated, the 121.5/243.0 MHz transmissions are used to home in on the crash site.
NOTE: Effective February 1, 2009, COSPAS-SARSAT has terminated satellite processing of
distress signals from 121.5 and 243.0 MHz beacons.
7) Aircraft communications transceivers are not capable of receiving 406 MHz transmissions; therefore,
the only methods of monitoring the ELT are:
a) The blinking cockpit remote switch LED,
b) The buzzer, or
c) 121.5/243.0 MHz transmissions, which can be monitored using the aircraft communications
transceiver or an AM radio tuned to 121.5 MHz.

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 18 of 66
SUBTASK 25-62-11-870-002
B. Components
1) The C406-2 Series ELT main assembly is housed in a high impact, fire resistant, polycarbonate plastic
case, which is enclosed in a protective mounting frame assembly made of similar material. See Figure
2.
NOTE: The ELT main assembly and its mounting frame assembly are capable of
withstanding extremely harsh environments and have been subjected to the rigorous
environmental testing required by COSPAS-SARSAT for certification.
Figure 2 C406-2 Series ELT and Mounting Frame Assembly
2) The cockpit-mounted remote switch assembly is comprised of an ELT status LED and control switch
and allows an operator to manually turn the ELT on (i.e., activate) for testing and reset (i.e.,
deactivate) the ELT. See Figure 3.
NOTE: The ELT CANNOT be disarmed or disabled from the cockpit. Cockpit operation is
limited to deactivating or manually activating the ELT.
Figure 3 Remote Switch Front View

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 19 of 66
3) The buzzer (i.e., horn) provides an audible alert when the ELT is active. See Figure 4.
Figure 4 Buzzer
4) The battery pack for the C406-2 Series ELT consists of four “D” size lithium manganese dioxide cells
connected in series. To prevent the cells from being charged, diodes are connected across each cell
and fuses are connected to the output. See Figure 5.
Figure 5 Battery Pack Assembly
5) Five dual-input antennas are approved for use with the C406-2 Series ELT. Selection of the proper
antenna is dependent upon end use, aircraft configuration and speed, and other factors. See Figure
6.
Figure 6 Antennas

ARTEX PRODUCTS / ACR ELECTRONICS, INC
DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL
C406-2 (453-5000), C406-2HM (453-5001)
570-5000 Rev. U Company Confidential 25-62-11 Page 20 of 66
TASK 25-62-11-870-802
2. Operation
SUBTASK 25-62-11-870-001
A. Operational Overview
1) See Figure 7.
Figure 7 ELT Operational Flow Diagram
2) A primary feature of the C406-2 Series ELT is its simplicity of operation. As long as the ELT is
connected to the remote switch harness ELT connector, such that pins 5 and 8 are jumpered (G-
switch loop), it will activate in the event of a crash.
NOTE: Neither the cockpit remote switch or the ELT local switch can be positioned in such a
manner as to prevent automatic activation when the ELT is connected properly.
3) ELT operation is designed to prevent human error and misuse in regards to automatic activation. The
ELT cannot be activated by dropping, rough handling or during shipping.
4) When the ELT is activated, the presence of the emergency sweep tone and the flashing cockpit
remote switch panel LED indicates an active, normal functioning ELT. The cockpit panel LED must
immediately begin to flash continuously upon ELT activation.
5) The ELT is considered to be either “ACTIVE” or “INACTIVE”. When “INACTIVE”, the ELT is in a state
of rest and performs no functions. Taking the ELT from the “INACTIVE” state to the “ACTIVE” state
requires a positive switch transition from either the cockpit remote switch, ELT local switch, or G-
switch.
a) It is possible the primary G-switch or one of the auxiliary G-switches could activate the ELT in
either a fixed or rotor wing aircraft as the result of severe maneuvers or a very hard landing.
b) To take the ELT from an “ACTIVE” state back to an “INACTIVE” state, a “RESET” must occur. See
SUBTASK 25-62-11-870-004.
6) A warning buzzer is required under C126 TSO approval. The buzzer is powered by the ELT and
therefore not dependent upon the aircraft battery for operation. It is not designed to operate