BWI Eagle AIR-EAGLE SR PLUS User manual

AIR-EAGLE SR PLUS
36-FOB-4
2.4 GHz RF Transmitter
Document Date: 6/14/2023
Product Rev: 0

36-FOB-4
1
WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and installed, will be free
from defects in material and workmanship for a period of 1 year after date of purchase. Said warranty to
include the repair or replacement of defective equipment. This warranty does not cover damage due to
external causes, including accident, problems with electrical power, usage not in accordance with product
instructions, misuse, neglect, alteration, repair, improper installation, or improper testing. This limited
warranty, and any implied warranties that may exist under state law, apply only to the original purchaser of
the equipment, and last only for as long as such purchaser continues to own the equipment. This warranty
replaces all other warranties, express or implied including, but not limited to, the implied warranties or
merchantability and fitness for a particular purpose. BWI Eagle makes no express warranties beyond
those stated here. BWI disclaims without limitation, implied warranties of merchantability and fitness for a
particular purpose. Some jurisdictions do not allow the exclusion of implied warranties so this limitation
may not apply to you. To obtain warranty service, contact BWI Eagle for a return material authorization.
When returning equipment to BWI Eagle, the customer assumes the risk of damage or loss during
shipping and is responsible for the shipping costs incurred.
SIGNAL RANGE
Max range statements are estimates based on a clear line of sight with few interferences. Actual range will
vary based on transmitting power, orientation of transmitter and receiver, height of transmitting and
receiving antennas, weather conditions, electronic interference, terrain, and physical obstacles, including
but not limited to; walls, building structures, trees (foliage), metal objects, and landscape (hills, mountains).
WIRELESS STOP, ASTOP, and E-STOP SYSTEMS
Wireless E-STOP systems should never be considered a primary life-saving device.
At least one hard-wired switch must be available in the event the wireless system is
not operational. Failure to comply may result in serious injury or death to personnel
and damage to equipment.
Wireless STOP and ASTOP transmitters are not failsafe emergency stop controls.
They are NOT to be used as a life-saving device. They are designed for wireless
control of equipment or vehicle remote operation. Failure to use as intended may
result in serious injury or death to personnel and damage to equipment.

36-FOB-4
2
INTRODUCTION
The Air-Eagle SR Plus is an RF system designed for short range wireless remote control of electrical
apparatus in a variety of industrial applications. Systems can consist of any number of receivers and
handheld or contact input transmitters working together to create a short to medium range radio
frequency system that operates hazardous or hard-to-reach equipment from safe, convenient locations.
The key fob transmitter can be used as an alternative to the 4-button handheld unit in many Air-Eagle SR
Plus systems (see comparison chart below). Like the original handheld unit (36-HH-4), the key fob (36-
FOB-4) is equipped to send four unique digital commands to an Air-Eagle SR Plus receiver.
The key fob will automatically go into “sleep” mode when not in use to dramatically extend battery life.
Eight user selectable frequencies allow multiple systems to be used in the same area without
interference. Like all Air-Eagle SR Plus transmitters, the key fob utilizes spread-spectrum technology and
provides the utmost in security and reliability.
Key Fob vs Handheld Comparison
The key fob transmits the identical RF codes as the handheld transmitter. But, there are differences
between the two models to consider.
Key Fob
Handheld
Operating
Range
Up to 250 ft.
Reduced power. Smaller enclosure
facilitates smaller battery (CR2032)
Up to 600 ft.
Full power. Larger enclosure facilitates
high capacity AAA batteries
Transmitting
Mode
Momentary (One-Shot).
Transmits RF code once when button is
pressed. Does not transmit again until
button is released and pressed again.
Maintained Momentary.
Transmits RF code repeatedly as long as
button is held. Continues to transmit until
button is released.
Size
Smaller size, similar to an
automobile key fob. Easily fits
in pocket or attaches to key
ring.
Larger size. Comfortably fits in
hand. Includes belt clip for
carrying.

36-FOB-4
3
INITIAL OPERATION SET-UP
This transmitter comes ready to operate with batteries installed. factory set to frequency 1 and power
level 2 (max range of 250 feet). To change the default settings, see FREQUENCY PROGRAMMING and
POWER LEVEL PROGRAMMING sections.
CONTROLS & INDICATORS
TX LED
LED illuminates RED when button is pressed, then blinks slowly
(approximately once per second) until button is released.
When this LED blinks rapidly (approximately 4 times per second) during
or after a button is pressed, the battery needs to be replaced. *
Buttons 1 - 4
Transmits single (one-shot) individual button RF codes to the receiver.
*Note: The low battery notification signals have been improved to provide more noticeable
indications to the user. When a low battery is first detected, the TX LED will blink rapidly several
times after any button is released. If it is possible to replace the batteries now, please do so. If not,
the operator has approximately 15 more button activations. After that, the TX LED will blink
RED/GREEN rapidly. No RF transmissions are being sent at this point. The battery must be
replaced to resume normal operation.
SPECIFICATIONS
Keypad
Durable Sealed Micro Switch Keypad –Eliminates dust, dirt and
moisture failures
Enclosure
ABS UL94 HB / TPE (blue)
Designed to meet the specifications of IP67
Power Requirements
3.0 VDC
Battery Type
(1) CR2032 lithium button cell. *See note below.
Battery Life (Active Usage)
Up to 3 months
Battery Life (Sleep Mode)
Up to 1 Year
Transmit Frequency
2.4GHz Spread Spectrum
RF Networks
Eight Independent Network Frequencies
RF Output Power
User selectable from 2mW or 6.4 mW
Transmit Range
User selectable from 75 Feet or 250 Feet **See note below.
Operating Temperature
-40oF to +185oF
*Note: Current frequency setting is maintained in flash memory during battery replacement. No
reprogramming of frequency setting is necessary.
**Note: Range statements are estimates based on a clear line of sight with few interferences. Actual
range will vary based on transmitting power, orientation of transmitter and receiver, height of
transmitting and receiving antennas, weather conditions, electronic interference, terrain, and physical
obstacles, including but not limited to; walls, building structures, trees (foliage), metal objects, and
landscape (hills, mountains).

36-FOB-4
4
FREQUENCY PROGRAMMING
Read instructions completely before beginning programming procedure.
Transmitters are shipped from the factory set to Frequency 1 by default. The frequency can be changed
at any time by following the procedure below. Once changed, it is recommended to label the transmitter
with the selected frequency number.
*Note: Current frequency setting is maintained in flash memory during battery replacement. No
reprogramming of frequency setting is necessary after battery change.
To Check Current Frequency:
1. Press Buttons 3 & 4 simultaneously for approximately 4 seconds until the TX LED illuminates
RED.
2. Release all buttons. Watch while TX LED begins to blink.
3. The TX LED will blink RED one, two, three, or four times for frequencies 1, 2, 3, or 4, or will blink
GREEN one, two, three, or four times for frequencies 5, 6, 7, or 8. See table below for
clarification.
Operating Frequency
TX LED Flashes
Frequency 1
1 RED flash
Frequency 2
2 RED flashes
Frequency 3
3 RED flashes
Frequency 4
4 RED flashes
Frequency 5
1 GREEN flash
Frequency 6
2 GREEN flashes
Frequency 7
3 GREEN flashes
Frequency 8
4 GREEN flashes
To Select Frequency 1 - 4:
1. Press Buttons 3 & 4 simultaneously for approximately 4 seconds until the TX LED illuminates
RED.
2. Release all buttons. While TX LED is still RED press Button 1 to select Frequency 1, Button 2 to
select Frequency 2, etc.
3. The TX LED will blink to confirm the frequency selection has been accepted. It will blink RED
once to confirm Frequency 1, blink twice to confirm Frequency 2, etc.
Note - If the TX LED goes out before a frequency is selected, the setting will not change, and the
LED will blink corresponding to the current frequency setting. To change the frequency, start
again at step 1.
<< Continued >>

36-FOB-4
5
FREQUENCY PROGRAMMING (Continued)
To Select Frequency 5 - 8:
1. Press Buttons 3 & 4 simultaneously for approximately 7 seconds until the TX LED illuminates
GREEN.
2. Release Buttons 3 & 4. While TX LED is still GREEN press Button 1 to select Frequency 5,
Button 2 to select Frequency 6, etc.
3. The TX LED will blink to confirm the frequency selection has been accepted. It will blink GREEN
once to confirm Frequency 5, blink twice to confirm Frequency 6, etc.
Note - If the TX LED goes out before a frequency is selected, the setting will not change, and the
LED will blink corresponding to the current frequency setting. To change the frequency, start
again at step 1.
Programming is now complete. Repeat the above procedure to change the frequency at any time.
POWER LEVEL PROGRAMMING
Read instructions completely before beginning programming procedure.
Transmitters are shipped from the factory set to Power Level 2 (max range 250 ft) by default. The power
level can be changed at any time by following the procedure below.
*Note: Current power level setting is maintained in flash memory during battery replacement. No
reprogramming of power level setting is necessary after battery change.
To Check Current Power Level:
1. Press Buttons 3 & 4 simultaneously for approximately 11 seconds until the TX LED blinks
GREEN.
2. Release all buttons. Watch while TX LED continues to blink for 10 seconds, goes out, then begins
to blink again.
3. The TX LED will blink GREEN one or two times corresponding to the power level setting. See
table below for clarification.
Power Level
TX LED Flashes
Power Level 1 –Approx. 75’ Range
1 GREEN flash
Power Level 2 –Approx. 250’ Range
2 GREEN flashes
To Select Power Level 1 or 2:
1. Press Buttons 3 & 4 simultaneously for approximately 11 seconds until the TX LED blinks
GREEN.
2. Release all buttons. While the TX LED is still blinking GREEN press Button 1 to select Power
Level 1, Button 2 to select Power Level 2.
<< Continued >>

36-FOB-4
6
POWER LEVEL PROGRAMMING (Continued)
3. The TX LED will blink to confirm the power level selection has been accepted. It will blink GREEN
once to confirm power level 1, blink twice to confirm power level 2.
Note - If the TX LED goes out before a power level is selected, the setting will not change, and
the LED will blink corresponding to the current power level setting. To change the power level,
start again at step 1.
Programming is now complete. Repeat the above procedure to change the power level at any time.
DIMENSIONS
APPROVALS
United States (FCC)
MCQ-XBEE3
Canada (IC)
1846A-XBEE3
Europe (CE)
ETSI
Australia
RCM
Brazil
ANATEL 06329-18-01209