Arylic Up2stream 2.0 Amp V3 User manual

enabled, and it is also a all-in-one solution for DIYers to make their customized wireless audio system. After connecting the device to your
home network, with our 4STREAM app, you can play music from your home NAS, USB pen drive, cell phone memory or from online streaming
services like Spotify, Deezer, Tidal, Qobuz and so on. The wireless multiroom audio system can play the same music to each room in sync or
play different music to different rooms.
1. Introduction
Up2stream 2.0 Amp V3 User Manual
2. What's in the box
3. Interface
4. Connection Diagram
DC-IN
Mirco USB
USB
Line-in
RIN,GND,GND,LIN
GND,MIC2,MIC1,GND(reserved)
GPIO2,GPIO1,GND,VCC
GND,SPDIF2
Ethernet RJ45
B
C
D
E
H
G
I
J
K
L
M
N
O
F
Power Button
WiFi Module
Bluetooth Antenna
WiFi Antenna
IR
LED
IIC,ADC_KEY,LED,RESET,TX,RX,GND,VCC
Speaker-Out
(R+,R-,L+,L-)
B DC F IHG J
K
L
M
O
Q
Q
P
P
R
R
N
E
*
UpStream AMP2.0
Acrylic Casing
More accessories coming soon at www.arylic.com
4pin analog connector
External SPDIF Board
4pin cable
External Button Board
WiFi Antenna
External Knob Board
User Manual
Q PH2.0-13P: IIC_SDA, IIC_SCL, IR, ADC_KEY, LED_BLUE,
LED_RED, LED_WHITE, LED_GREEN, RESET, TX, RX, GND,
VCC3V3
IIC_SDA, IIC_SCL: This is reserved for display panel.
IR is used for extend IR receiver.
KEY is used for external buttons, refer to the circuit right for key
The LED pins are used to extend the LED, and are common-anode
connected.
You should connect 3.3V to a current limit resister and then to LED
and then to the pin.
TX/RX are UART interface to send events and receive controls.
L PH2.0-2P:GND, SPDIF2: This is reserved for external SPDIF
input.
E PH2.0-4P:R_IN, GND, GND, L_IN: For analoginput toup2stream
amp board, it has the same signal as the 3.5mm Aux jack.
D PH2.0-4P: GND, MIC2, MIC1, GND: This is reserved for future
use.
Further Notes
C27
0.1uF
R47 10K
MODE
PLAY/PAUSE
NEXT
PREV
VOL+
R60
1K
R61
2.2K
R62
3.6K
R63
5.6K
R64
100R
VOL-
R65
8.2K
MUTE
R66
12K NUM1
R67
18K NUM2
R68
27K
NUM3
R69
47K
NUM4
R70
100K
KEY
VDD3V3
DGND
DGND
*LED_WHITE reserved
for future use
*J Power Button: Short press to power off and on; When in WiFi mode, long press (press and hold the button for more than 5 seconds) to
reset WiFi settings and enter the paring mode; When in Bluetooth mode, long press to terminate current connection.

1. Power the device.
2. Direct Mode: If you don’t have router, please choose direct mode, then you
can play your music from your storage from 4STREAM app .
3.Network Mode : Connect your phone to SoundSystem WiFi.
3.1. Go for mobile device WLAN settings> Connect
mobile device to WiFi hotspot SoundSystem_xxxx you will see a WiFi logo .
(short press the reset button if the Wi-Fi hotspot is not found)
3.2. Open the 4STREAM application, follow the guides
3.3 Choose the 2.4G network( rst time connection require connect your router
2.4G channel), enter router password>wait for the device to be congured.
* For multiple units connecting to same router, router password will be saved .
*If change router or router password, please press WiFi reset button on the
product .
6. Specication
5.1 App download
Download the 4STREAM application from App Store for iOS based devices and Google Play Store for
Android based devices.
The application supports English, Spanish, French, German, Italian, Portugese, Korean, Simplied
Chinese,Traditional Chinese and Japanese
5. How To Use
Connectivity
Wireless network IEEE802.11 b/g/n 2.4G
Ethernet Single 10/100M RJ45
Bluetooth 5.0, SBS/AAC
USB Host Play USB music
Bluetooth Distance 10M
Power Input DC 12V - 26V
Audio Input Analog 3.5mm/4pin connector/Micro USB
Audio output Analog Speaker out
(PIN SPACE-5.0mm)
Frequency response 20Hz to 20kHz
Speaker Power
2×50-W into a 4-Ω BTL Load at 21 V
2×30-W into a 8-Ω BTL Load at 24 V
2×15-W into a 8-Ω BTL Load at 15 V
THD+N 0.03%, @1kHz 50W+50W 24V-4Ω
Speaker Impedance 4-8ohms
Music Format FLAC/MP3/AAC/AAC+/ALAC/APE/WAV
Decoding Up to 24bit/192kHz
Protocols AirPlay, DLNA, UPnP, Spotify Connect, Qplay
Dimensions 110*80*22m
IR Remote Controller Optional
Scan the QR codes below for more
www.arylic.com
Complete User Manual
Support: [email protected]
4STREAM App Facebook: arylicme YouTube:Arylic
4STREAM
5.3 Connection via LAN
Plug in the wired cable to the RJ45 Ethernet, the device will show on the app in about 10 seconds. (Note: the cell phone and the device must
be in the same network)
The application will notify you in app when there is a
new rmware version available.It's recommended to
update rmware whenever available as this might not
only correct bugs or improve security,but also can add
new features or services.
5.7 Firmware update
Power up and connect the Up2Stream AMP to your PC with USB cable (make sure it’s a data cable
including the signal wires). The PC will automatically discover a USB sound card, and when you
activated it as the system main output, the PC will send the audio output over Up2Stream AMP in
digital (44.1KHz/16bits).
You can stream to other Up2Stream devices over multiroom connection.
NOTE: there’s about 3 seconds delay for multiroom slave devices.
5.5 USB audio
To use bluetooth ,please swtich to bluetooth via
app or by remote controller,then find bluetooth
device SoundSystem_XXXX from your phone
bluetooth setting and pair it .
5.4 Bluetooth
Connect the Up2Stream device to your PC with USB cable (make sure it’s a data cable including the signal wires). And open the program
Up2Stream DSP Tool (only support Windows.), and you can tune audio effects conveniently, including Music Noise Suppressor, Virtual
Bass, Stereo Widener, Exciter, 10 bands EQ, etc. After editing the audio effects, you can save the changes to the device so the tuned
effects will remain. You can get more information from our website www.arylic.com，or from the Up2Stream DSP Tool manual.
5.6 Up2Stream DSP Audio Effects Tool (Sell Separately)
5.2 Connection
*Attention for Android users
Different brand mobile phones may ask you to allow
to use SoundSystem WiFi network, please choose
yes, if not, you may not able to set up successfully .
It may also ask you to authorize other things, please
choose yes or it may affect your use.