Arylic Up2Stream AMP v4 Instruction Manual

Up2Stream AMP v4 User Manual
1. Introduction
Up2Stream AMP v4 is a WiFi and Bluetooth 5.0 stereo/mono amplifier board that can be applied into your existing regular audio system
to make it wireless enabled, it is also a all-in-one solution for DIYers to make their customized wireless audio system. Up2Sream AMP v4
can switch between stereo and mono mode, stereo can provide max. 50W L&R channels, and mono mode will mixed L&R channel and
provide a single max. 100W channel. Once connected to your home network, using our 4Stream app, you can play music from your
mobile, NAS, USB pen drive or from online streaming services like Spotify, Deezer, Tidal, Qobuz and more. With multiple devices, the
wireless multiroom audio system can play the same music to each room in sync or play different music to different rooms.
10. Power Button: Short press to power off and on; When in WiFi mode, long press (press and hold for 5 secs) to reset WiFi settings
and enter pairing mode; When in Bluetooth mode, long press to terminate current connection.
*Hold Power button first then plug in the power cable can force the device to enter WiFI mode. If you have setup router connection
before, the device will automatically connect to that router.
20. Switching Stereo/Mono mode: The four jumpers’ position will decide which mode Up2Stream AMP v4 is:
2. What’s in the box
3. Interface
Screw Driver Antenna x2 User’s Manual4Pin Analog ConnectorUp2Stream AMP v4
External Button Board
DC-IN
Speaker OUT
(Stereo: R+,R-,L+,L-) (Mono: +,+,-,-)
GND, MIC2, MIC1, GND
Line IN (R_IN, GND, GND, L_IN)
Line IN
Mirco USB
GND, B0, B1, GPIO
USB
Ethernet RJ45
Power Button
GND, SPDIF
GPIO2, GPIO1, GND, VCC3V3
SPDIF, MCLK, IIS_DATA, BCLK, LRCK, GND, VCC_3V3
Bluetooth Antenna
WiFi Module
WiFi Antenna
IR
IIC, IR, ADC_KEY, LED, RESET, TX, RX, GND, VCC3V3
XOUT, DGND, LOUT, AGND, ROUT
(Stereo: LOUT, ROUT) (Mono: XOUT)
Stereo/Mono Jumpers
+5V, GND
LED
V+,GND (12-24V DC in)
External Knob BoardExternal SPDIF BoardAcrylic Casing
*More accessories are available at www.arylic.com
Stereo Mode
Jumpers are on the top and middle row
NOTE: Operate with no Power Connected.
Mono Mode
Jumpers are on the middle and bottom row
0.1uF
10K
MODE
PLAY/PAUSE
NEXT
PREV
VOL+
VOL-
MUTE
NUM1
NUM2
NUM3
NUM4
1K
2.2K
3.6K
5.6K
100R
8.2K
12K
18K
27K
47K
100K
KEY
VDD3V3
AMP V4
DGND
Further Notes
3. PH2.0-4P: GND, MIC2, MIC1, GND: This is reserved for future use.
4. PH2.0-4P: R_IN, GND, GND, L_IN: Analog input to Up2Stream AMP v4 board, it has
the same signal as the 3.5mm Line IN jack.
6. Micro USB: For connection with PC to support USB soundcard, and the
ACPWorkbench tool.
11. PH2.0-2P: GND, SPDIF: This is for external SPDIF output/input.
12. PH2.0-4P: GPIO2, GPIO1, GND, VCC3V3: GPIO2 and GPIO1 is used to connect a
coding key, should be used for volume control.
13. PH2.0-7P: SPDIF, MCLK, IIS_DATA, BCLK, LRCK, GND, VCC_3V3: This is for digital
output extension:
SPDIF is for external SPDIF output/input (same as #11)
For IIS, BCLK is 2.8MHz, LRCK is 44.1KHz, MCLK is 11.288MHz, DOUT following the
standard IIS data format and have 16 bits depth. The system is running in master
mode, you should make sure the IIS port of connected device is running in slave
mode.
18. PH2.0-13P: IIC_SDA, IIC_SCL, IR, ADC_KEY, LED_RED, LED_BLUE, LED_WHITE,
LED_GREEN, RESET, TX, RX, GND, VCC3V3
IIC_SDA, IIC_SCL: This is reserved for display panel.
IR is used for extend IR receiver.
ADC_KEY is used for external buttons, please refer to the circuit on the right for key
definitions.
The LED pins are used to extend the LED and are common-anode connected. You
should connect 3.3V to a current limit resister and then to LED then to the pin.
RESET is used to extend the WiFi reset button (Power Button).
TX/RX are UART interface to send events and receive controls.
19. PH2.0-5P: XOUT, DGND, LOUT, AGND, ROUT: Analog output, use XOUT when in Mono mode and ROUT, LOUT when in Stereo
mode, these has the same signal as the speaker out.
21. PH2.0-2P: 5V+, GND: 5V power output for other device.
23. PH2.0-2P: V+, GND: 12-24V power input (same as the DC IN port)

4. Connection Diagram
5. How To Use
5.1 App download
Download the 4STREAM application from App Store for iOS based devices and
Google Play Store for Android based devices.
The application supports English, Spanish, French, German, Italian, Portuguese,
Korean, Simplified Chinese, Traditional Chinese and Japanese
5.2 First time usage & BLE WiFi Setup
1) Hold the POWER button then plug in the power cable.
2) The LED light will start flashing, release the button and wait till the LED flash
slowly.
3) Make sure your mobile has connected to your home network using 2.4G and
your GPS and Bluetooth is on.
4) Open 4Stream APP, for Android device, the system will ask for permission to use
GPS data & File storage, please click accept to continue.
This GPS permission is setup by Google for BLE usage, once setup is finish you can
go to system settings and disable it, file storage permission is to let 4Stream
access your mp3 files store in your mobile.
5) 4Stream APP will list out all the device available for setup, choose the one you
want.
6) 4Stream APP will then ask you to choose the network you want the device to
connect to, choose the one you want to connect.
7) Now enter password for your network, if this is not the network you want the
device to connect, you can change it to the desire one.
8) Once connection is finished, it will automatically check for new updates.
9) Then you can change the name of the device. You can select a preset one or
enter your own.
10) After you define the name of the device, you will see it appears in the device list
in 4stream app and now you can start streaming music.
*If you change to another router, or the password of the connected router has
been changed, please long press POWER button for 5 secs in WiFi mode to reset
the connection.
* Hold POWER button then plug in the power can force the device to enter WiFi
mode. If you have setup router connection before, the device will auto connect to
that router.
There is another way to setup Wifi if the above method has faild:
1. Hold the POWER button then plug in the power cable.
2. The LED light will start flashing, release the button and wait till the LED flash
slowly.
3. Goto your mobile WiFi settings and search for SoundSystem_xxxx WiFi and
connect. *If you cannot find SoundSystem connection, long press the POWER
button for 5 secs and then refresh your mobile’s WiFi listing.
4. Open 4Stream APP and there will be 2 options: Direct Mode & Add Device.
5. Direct Mode: If you don’t have router, please choose direct mode. After
connected, you can play music store in your mobile.
6. Add Device: After you choose add device, select the router SSID you want your
Up2stream device connect to (enter password if required) and select continue.
7. Once connected, you can change the name of the device. You can select a
preset one or enter your own.
8. After you define the name of the device, you will see it appears in the device list
in 4stream app and now you can start streaming music.
6. Specification
5.5 USB Audio
Power up and connect the Up2Stream AMP to your PC with USB cable (Make sure
it’s a data cable including the signal wires). The PC will automatically discover a
USB sound card, and when you activated it as the system main output, the PC will
send the audio output over Up2Stream AMP in digital (44.1KHz/16bits). You can
stream to other Up2Stream devices over multiroom connection. NOTE: there’s
about 3 seconds delay for multiroom slave devices.
5.6 Up2Stream ACPWorkbench (Sell Separately)
Connect the Up2Stream device to your PC with USB cable (make sure it’s a data
cable including the signal wires). And open the program ACPWorkbench (only
support Windows.), and you can tune audio effects conveniently, including Music
Noise Suppressor, Virtual Bass, Stereo Widener, Exciter, 10 bands EQ, Configure
output channel and PIN configs. After editing the audio effects, you can save the
changes to the device so the tuned effects will remain. You can get more
information from our website www.arylic.com，or from the Up2 Stream DSP Tool
manual.
5.7 Firmware Update
The application will notify you in app when there is a new firmware version
available. It is recommended to update firmware whenever available as this might
not only correct bugs or improve security, but also can add new features or
services.
5.3 Connection via LAN
Plug in the wired cable to the RJ45 Ethernet, the device will show on the app in
about 10 seconds. (Note: the cell phone and the device must be in the same
network)
5.4 Bluetooth
To use bluetooth, please switch to bluetooth via app or by remote controller, then
find the bluetooth device SoundSystem_XXXX from your phone bluetooth setting
and pair it.
*Attention for Android users Different brand mobile phones may ask you to allow
to use SoundSystem WiFi network, please choose yes, if not, you may not able to
set up successfully. It may also ask you to authorize other things, please choose
yes or it may affect your use.
Connectivity
Wireless network IEEE802.11 b/g/n 2.4G
Ethernet Single 10/100M RJ45
Bluetooth 5.0, SBS/AAC
USB Host Play USB music
Bluetooth Distance 10M
Power Input 12V-24V/DC in,12V-24V 2Pin Connector
Audio Input Analog 3.5mm/4Pin Connector/Micro USB
Audio output
Analog Speaker Out(Pin Space 5.0mm)
4Pin Connector (Stereo)
2Pin Connector (Mono) /SPDIF Pin Out
Frequency response 20Hz to 20kHz
Scan the QR codes below for more
www.arylic.com
Support: [email protected]
4STREAM App
Facebook: arylicme YouTube:Arylic
Speaker
Power
Mono
Stereo
100W @ 2ohm load at 24V
60W @ 4ohm load at 21V
30W @ 8ohm load at 18V
2x50W @ 4ohm load at 21V
2x30W @ 8ohm load at 24V
2x15W @ 8ohm load at 15V
THD+N 0.03%, @1kHz 50W+50W 24V-4Ω
Speaker Impedance 4-8Ω
Music Format FLAC/MP3/AAC/AAC+/ALAC/APE/WAV
Decoding Up to 24bit/192kHz
Protocols AirPlay, DLNA, UPnP, Spotify Connect, Qplay
Dimensions 110*80*22mm
IR Remote Controller Optional