Ascon Pool MS3D-UD User manual

MS3D-UD
MULTI SOLAR
CONTROLLER
UP-DOWN

INSTALLATION: INCLUDED
Solar Controller
Down pipe Sensor
Up pipe Sensor
Mounting kit and template

INSTALLATION: REQUIRED
6mm Masonry drill bit
(required for raw plugs) P-2 Phillips head
screw Driver
Drill with hammer action ½” or 12.5mm Drill bit
Or cutting Tool (ms-Drill)

INSTALLATION: DO’S
3.5m
Unit must be 3.5m from pool zone
Less than 1.5m from the pump
1.5m
Unit must be installed in the upright
position 1 metre from the ground
1m
Unit must be mounted using screws provided.

INSTALLATION: DO NOT’S!
Do not immerse.
Do not place unit upside down.
Do not place within direct splashing
or spray from the pool.

INSTALLATION: UP PIPE SENSOR
Using the 12.5mm drill bit,
drill a hole into the up pipe.
Plug sensor cable into the unit using
the red connectors.
Put the grommet in first,
then push in the up pipe sensor.

INSTALLATION: DOWN PIPE SENSOR
Using the 12.5mm drill bit,
drill a hole into the down pipe.
Put the grommet in first,
then push in the down pipe sensor.
Attach the cables to the unit
using the red connectors.

Plug controller piggy back
into GPO if a stand alone
system.
Plug the solar pump into
the base of solar controller
INSTALLATION:
For a ‘stand alone’ system

INSTALLATION:
For an ‘integrated’ system
Plug the chlorinator into the power point
Plug the solar controller grey piggy back
into the chlorinator.
Plug the filter pump into the grey piggy back
Plug the solar pump into the solar controller

OPERATION: START UP
After 2 mins the unit will run for at least
6 mins to reset the down pipe sensor.
When the unit is turned
on, there will be a period
of 2 mins while the MS3D-UD
and the solar pump synchronise
(indicated by flashing light).

OPERATION: CLOCK SET UP
When the unit is turned
on, the set time LED will be
flashing. Set the time using
the for the hours and the
for the minutes.
The clock will need to be set after the unit is powered up.

OPERATION: COMFORT TEMP ADJUSTMENT
Press button
to increase to
maximum 40°C
by 1°C increments.
Press button to
decrease to
minimum 20°C
by 1°C increments.
When the comfort temperature is set,
this temperature will be stored, even
when the unit is turned off.
The comfort temperature is the temperature the user wants their pool to be.

OPERATION: DIFFERENTIAL TEMP ADJUSTMENT
The differential temperature is the difference in the temperature between the up pipe and the down pipe.
Press the , and
buttons at the same time.
The unit will show on
the display. The current
differential is displayed.
To change the differential,
press the button to increase,
and the button to decrease.

OPERATION: FINISH TIME ADJUSTMENT
The time of the day that the unit will cease operation until 8am the next day.
The default time is 4pm. (Unit operates in 24 hour time)
Press the button and the
button at the same time.
The unit will display .
Use the button the adjust the
hours and the button to adjust
the minutes.
Between the finish time and 8am the unit will display Nop while
The unit is not operating pump.

OPERATION: DISPLAY MODE
To read up and down pipe
temperatures, clock and comfort
temperature settings, press
The display mode allows the user to check each mode setting without accessing or changing the current settings.
The unit will cycle through the
settings showing:
UFor the up pipe temp.
C For the comfort setting.
L For the last up pipe temp.
P
For the down pipe temp.
H Shows the clock hours.
MShows the clock minutes.

OPERATION: WINTER MODE
At the end of the season
press for winter mode.
At the start of the season
press for normal
operation.
Winter mode allows the users solar system to function during cooler months.
This extends the life of the solar heating system.

OPERATION: OVERRIDE
Override On
To select a 4 hour override on,
press and hold the
and at the same
time for 5 seconds.
What does override do?
To select a 1 hour override,
Press and at the same
time.
Press both buttons again
to cancel the operation.

OPERATION: CALIBRATION
Press and
to calibrate the pool sensor
Display reads CAL then
+00 .
To calibrate the unit….
Press the or to offset
the temperature.

TROUBLE SHOOTING GUIDE

For further information, please refer to the
Installation Guide and Instruction Manual
www.asconpool.com.au