Ascon Pool C1200 User manual

OVERRIDE ON
To run the pump manually, press the Plus (+) button. The unit display will toggle
between “On” and the time.
IMPORTANT: The pump will run continuously until this mode is cancelled.
To return to normal operation, press the PLUS (+) button again.
OVERRIDE OFF
To prevent the pump from coming on, press the Minus (-) button. The unit display
will toggle between “OFF” and the time.
IMPORTANT: The pump will stay off until this mode is cancelled.
To return to normal operation, press the Minus (-) button again.
DISPLAY MODE
To view the pump running times press the Display button. The pump on time
is displayed. Press the Display button again and the pump off time is
displayed. Repeat this sequence until “End” is displayed. After 5 seconds the
unit returns to normal operation.
MULTI eCLOCK
Model C1200
The sun always shines with Ascon Pool
r01
Associated Controls (Australia) Pty Limited,
ABN 210 002 245 64
2-4 Norfolk Rd, Greenacre NSW 2190, Australia. PO Box 5605, Chullora NSW 2190
Tel: ++61 2 9642 4922
Email: [e-mail] web: www.asconpool.com.au
25247-01.PDF 104186

MULTI eCLOCK
The MULTI eCLOCK is designed to give you automatic time control of your
swimming pool filtration systems. By following these simple installation and
operating instructions you will enjoy trouble free operation for many years.
THIS UNIT IS COVERED BY A 12 MONTH WARRANTY
CAUTION: DO NOT OPEN THE CASE OF YOUR MULTI eCLOCK. IT IS NOT
USER SERVICEABLE. IF THE POWER CORD IS DAMAGED, IT MUST BE
REPLACED BY THE MANUFACTURER OR AN AUTHORISED AGENT.
OPENING THE CASE WILL VOID YOUR WARRANTY. THE UNIT MUST BE
INSTALLED IN THE UPRIGHT POSITION.
NOTE: ONLY THE FILTER PUMP SHOULD BE PLUGGED INTO THE BOTTOM
OF THE UNIT.
INSTALLATION
The MULTI eCLOCK is weather resistant, however it should be mounted in a
sheltered position where it is not exposed to direct weather, splashing or spray
from the pool or filtration equipment. Electrical building regulations specify
that the MULTI eCLOCK must not be mounted within 3 meters of the pool.
Fix the unit to a wall or post, within 1.5 meters of a 240 volt outlet and within 2
meters of the Filter pump. Mounting points are provided on the back.
POWER CONNECTION
Power is supplied through a standard 240 volt lead. A piggyback socket is provided
on the lead if you need to run other equipment the one power outlet . Power for the
filter pump comes from the socket on the bottom of the MULTI eCLOCK.
ONLY THE FILTER PUMP IS TO BE CONNECTED TO THE MULTI eCLOCK.
MORE THAN THIS WILL DAMAGE THE ELECTRONICS AND VOID YOUR
WARRANTY.
Maximum Pump rating - 2HP
TIME CLOCK/BATTERY INFORMATION
The MULTI eCLOCK uses a Real Time Clock that runs in 24 hour mode and has a
battery backup in case of power failure. All settings are saved during a power
outage.
MULTI eCLOCK OPERATION
Note: The MULTI eCLOCK setup routines have a 5 second timeout. it is
recommended that the user reads the following instructions to help ease the setup
procedure.
TIME SET-UP
1. Press and hold the Display and Setup buttons together until “CLOC” appears.
2. Release the buttons and the time appears, with the decimal point turned on.
3. Use the Minus (-) button to adjust the hour, and the Plus (+) button to adjust
the minutes. The MULTI eCLOCK uses 24 hour time for its operation.
4. When the desired time has been set, leave the unit for 5 seconds. The unit saves
the time and begins timing, as seen by the flashing decimal point.
CLEARING PUMP ON/OFF TIMES
Press and hold the “Setup” button down for 5 sec., the unit will respond by
displaying “CLr” for approx. 1 sec. to indicate all blocks have been set to OFF.
PUMP ON/OFF SET-UP
1. Press the Setup button. This brings up the time “6.00”.
2. Continuously press the Setup button until the desired time is displayed.
3. Press the Plus (+) button to turn the pump on for the displayed 1/2hour block.
This is indicated by the Yellow LED, i.e. if “10.30” is displayed, the pump will be on
from 10:30 to 11:00.
4. Press the Minus (-) button to turn the pump off for the displayed 1/2hour block.
This is indicated by the Red LED, i.e. if “10.30” is displayed, the pump will be off
from 10:30 to 11:00.
5. For every continuous 1/2hr block of time that the pump is required to be on or
off, repeat steps 2, 3 and 4.
6. When the desired pump times have been set, leave the unit for 5 seconds. The
unit saves the information and returns to displaying the current time.