ascon J3 User manual

Double input indicator
with analogue output
1/8DIN - 96 x 48
J3 line cc
User Manual • M.I.U.J3 - 1/05.02 • Cod. J30-478-1AJ3 IE
ASCON spa
via Falzarego, 9/11
20021 Bollate
(Milano) Italy
Tel. [phone]
Fax [phone]
http://www.ascon.it
e-mail [email protected]
ASCON spa
ISO 9001
Certified
UL
CUS
LISTED
J3 EN•ed1 4-03-2005 16:37 Pagina 1

Double input indicator
with analogue output
1/8DIN - 96 x 48
J3 line cc
J3
I1 I2 I3 123
HLD
1604.3
MIN
4
UL
CUS
LISTED
J3 EN•ed1 4-03-2005 16:37 Pagina 1

2
Information
cc
NOTES
ON ELECTRIC
SAFETY AND
ELECTROMAGNETIC
COMPATIBILITY
Please, read these instructions carefully before proceeding with the installation of the
controller.
Class II instrument, rearl panel mounting.
This indicator has been designed in compliance with:
Regulations on electrical apparatus (appliance, systems and installations) according to
the European Community directive 73/23/EEC amended by the European Community direc-
tive 93/68/EEC and the Regulations on the essential protection requirements in electrical
apparatus EN61010-1 : 93 + A2:95.
Regulations on Electromagnetic Compatibility according to the European Community
directive #89/336/EEC, amended by the European Community directive #92/31/EEC,
93/68/EEC, 98/13/EEC and the following regulations:
Regulations on RF emissions
EN61000-6-3 : 2001 residential environments
EN61000-6-4 : 2001 industrial environments
Regulation on RF immunity
EN61000-6-2 : 2001 industrial equipment and system
It is important to understand that it’s the responsibility of the installer to ensure compliance
with the regulations on safety requirements and EMC.
The device has no user serviceable parts and requires special equipment and specialised
engineers. Therefore, a repair cannot be carried out directly by the user. For service or repair,
contact the manufacturer or your sales represenattive.
All the information and warnings about safety and electromagnetic compatibility are
marked with the Bsign, at the side of the note.
J3 EN•ed1 4-03-2005 16:37 Pagina 2

3
Main universal input
Resources
IN1
IN2
IL1
IL2
IL3
Modbus RS485
Parameterisation
Supervision (option)
J3
12
12
MIN
MIN MAX
MAX PV
PV
HOLD
HOLD
PEAK
PEAK
HOLD
HOLD AVG
AVG
NO/NC
NO/NC
PV
PV
HOLD
HOLD
PEAK
PEAK
HOLD
HOLD ACK
ACK
ALM
ALM
Auxiliary input
3 digital input
Special functions
Digital inputs (IL1, IL2 or IL3) functions
OP1
OP2
OP3
OP4
OP5
Alarms Retransmission
Operating mode
IN1/IN2/CIN
OP1 OP2 OP3 OP4 OP5
Table of contents
TABLE OF CONTENTS
1INSTALLATION ...................................................Page 4
2ELECTRICAL CONNECTIONS .............Page 8
3PRODUCT CODING ......................................Page 14
4OPERATIONS......................................................Page 18
5DISPLAYS...............................................................Page 34
6COMMANDS........................................................Page 35
7TECHNICAL SPECIFICATIONS ...........Page 37
(option)
J3 EN•ed1 4-03-2005 16:37 Pagina 3

4
1- Installation
1INSTALLATION
Installation must only be carried out by
qualified personnel.
Before proceeding with the installation of this
indicator follow the instructions illustrated in
this manual with particular attention to the
installation precautions marked with the
Bsymbol, related to the European
Community directive on electrical protection
and electromagnetic compatibility.
B
To prevent hands or metal touching parts
that may be electrically live, the indicators
must be installed in an enclosure.
IP 20 Terminal block
EN61010 - 1
(IEC1010 - 1)
Product code label
Sealing front panel gasket
Mounting clamps
Front panel
IP65 protection
EN 650529 (IEC 529)
Panel
surface
1.1 GENERAL DESCRIPTION
J3 EN•ed1 4-03-2005 16:37 Pagina 4

5
1- Installation
1.2 DIMENSIONAL DETAILS 1.3 PANEL CUT-OUT
48 mm
1.89 in
110 mm
4.33 in
10 mm max.
0.39 in max.
96 mm
3.78 in
10 mm max.
0.39 in max.
45+0.6mm
1.78+0.023in
65mm min.
2.56 in min.
92+0.8 mm
3.62+0.031 in
113 mm min.
4.45 in min.
J3 EN•ed1 4-03-2005 16:37 Pagina 5

6
1 - Installation
Operating conditions
MAltitude up to 2000 m
TTemperature 0…50°C
%Rh Relative humidity 5…95 % non-condensing
1.4 ENVIRONMENTAL CONDITIONS B
Special conditions
MAltitude > 2000 m
TTemperature >50°C
%Rh Humidity > 95 %
PConducting atmosphere Use filter
Warm up
Use forced air ventilation
Use 24Vac supply version
Suggestions
Forbidden Conditions D
CCorrosive atmosphere
EExplosive atmosphere
J3 EN•ed1 4-03-2005 16:37 Pagina 6

7
1
3
2
2
1
2
1
12
1.5.1 INSERT
THE INSTRUMENT
1Prepare panel cut-out
2Check-front panel gasket
position
3Insert the instrument through
the cut-out
1.5.2 INSTALLATION
SECURING
1Fit the mounting clamps as
shown
2Push the mounting clamps
toward the panel surface to
secure the instrument
1.5.3 CLAMPS
REMOVING
1Insert the screwdriver in the
clips of the clamps
2Rotate the screwdriver
1.5.4 INSTRUMENT
UNPLUGGING B
1Push and
2Pull froward to remove the
instrument
1.5 PANEL MOUNTING [1]
UL note
[1] For Use on a Flat Surface of a Type 2
and Type 3 ‘raintight’ Enclosure.
Electrostatic discharges can
damage the instrument
Before removing
the instrument the
operator must dis-
charge himself to
ground.
1MΩ
1
1
2
1- Installation
J3 EN•ed1 4-03-2005 16:37 Pagina 7

2ELECTRICAL
CONNECTIONS
UL note
[1] Use 60/70 °C copper (Cu) conductor only.
28
27 30
29
26
25
7
19
31
8
20
32
9
33
10
34
11
23
35
12
24
36
123456
0,5
Nm
Rear
terminal
cover
Wire size
1 mm2(18 AWG
Solid/Stranded)
5.7 mm
0.22 in
8
Ø
L
28 screw terminals M3
Option terminals
Tightening torque 0.5 Nm
Positive screw-driver PH1
Negative screw-driver
0,8 x 4 mm
Terminals
Pin connector
q1.4 mm 0.055 in max.
Fork-shape AMP 165004
Ø 5.5 mm - 0.21 in
Stripped wire
L 5.5 mm - 0.21 in
2.1 TERMINAL BLOCK [1] B
2 - Electrical connections
N
L
RS485
1
2
3
4
5
6
7
8
9
10
11
12
19
20
23
24
25
26
27
28
29
30
31
32
33
34
35
36
LOGIC INPUTS (IL)
TC
mV
NC
C
NO
OP1
NO
C
NO
OP2
OP3
OP4
C
IN2
OP5
24V—
OUT
1
2
3
A
b
B
RTD
13
14
15
16
17
18
21
22
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
J3 EN•ed1 4-03-2005 16:37 Pagina 8