Pixie STP54BTAS User manual

1. Product Introduction
The PIXIE Ambience Touch Panel is a premium addition to the PIXIE
solution that elevates the smart home experience.
The PIXIE Touch Panel is configured after the PIXIE smart home has
been configured using the PIXIE App and is ideally used as a central
control hub for the home.
1.1 Product Features
• Control PIXIE devices installed throughout the home in a
centralised location.
• Matches the PIXIE Ambience faceplate range aesthetic
• 5.5 inch high-resolution wide-angle colour touch screen
• Four multifunction buttons for rapid access to commonly used
devices, groups and scenes
• RJ45 port for stable LAN connection and optimal operation
• Wi-Fi connection supported for situations where LAN cabling is
infeasible
• Supports Power over Ethernet (PoE), or 12V DC power input if POE is
not available. (Power supply purchased separately)
• Auto-adjustable display brightness
1.2 Pre-requisitions before setup
• Power: 12 V DC or PoE
• Network: LAN cable (recommended) or Wi-Fi
• PIXIE PLUS App:
- Ensure the PIXIE Plus App is up-to-date before installing
the PIXIE Ambience Touch panel.
- The mobile phone operating the PIXIE Plus App is on the
same network as the PIXIE Ambience Touch Panel.
• PIXIE Gateway:
- At least one PIXIE gateway is deployed, PIXIE Gateway
G3 (model NO. SGW3/BTAM) is highly recommended for
optimal performance.
- The PIXIE Gateway is on the same network as the PIXIE
Ambience Touch Panel.
Note
Though being compatible with PIXIE Gateway G1 (model NO.
SGW/BT) and PIXIE Gateway G3 (model NO. SGW3/BTAM), it’s highly
recommended to use the Touch Panel with PIXIE Gateway G3
(model NO. SGW3/BTAM) for optimal performance.
Please refer to the feature matrix below comparing the performance
of the PIXIE Ambience Touch Panel with PIXIE Gateway G1 and PIXIE
Gateway G3.
PIXIE Gateway G1
How many PIXIE Ambience Touch Panels can
work properly under the PIXIE PLUS account?
Updating of control data after changes
made in PIXIE Plus App and network
Connection stability Fair, subject to Wi-Fi coverage and
router status Ideal, due to LAN cable connection
1
Requires manual operation to
re-sync the data
Network formed with
PIXIE Gateway G3
Network formed with
Automatically re-syncs the data
8
Installation Instructions
STP54BTAS
AMBIENCE
Touch Panel
Devices must be installed by a
qualified electrician in accordance
with all national and local electrical
and construction codes and
regulations.
Do not connect inputs to mains.
The PIXIE Ambience Touch Panel is
compatible with the PIXIE Plus App
only and requires a PIXIE Gateway
to operate.
1.3 What’s included in the package
Pan head Screws * 2Touch Panel * 1 Mounting Template * 1Mounting Bracket * 1 Countersunk screw * 5 Expansion bolt * 5Pin Key * 1
Mounting Template
UP UP

Sensor window
Multifunction Button
LED indicator
LAN & PoE port
DC 12V input
Screen
RESTART button
SET button
2. Specifications and Capabilities
PIXIE Ambience
Touch Panel STP54BTAS White 120 x 148 x 38 212
12V DC (Min. 15W) / PoE
Product Description Model NO. Colour Dimensions L x W x H (mm)Power Input Weight (g)
1.4 Product features
The faceplate is detachable Touch panel main body
Front view with faceplate
Back view of touch panel main body Top view of touch panel main body
Display Size
Ethernet
Product Installation Orientation
Operating Ambient Temperature
Operating Humidity
IP Rating
5.5 inch (68 x 121 mm)
RJ45 port (10M/100M) 2.4 GHz
Interior residential or commercial
Horizontal wall mount
0-85% RH, NC 0-85% RH, NC
IP20
0℃- 40℃0℃- 60℃
720 x 1280
Storage Ambient Temperature
Wi-Fi
Product Application
Storage Humidity
Screen Resolution

148
120 38
46
12
-
3.1 First, use the provided mounting template to determine the
position for installation on the wall.
Make a cut-out on the wall according to the mounting
template.
3.3 Fix the mounting bracket onto the wall, with the appropriate screws and tools.
Fixing option 1 Fixing option 2
or
3. Installation process
3.2 Remove the metal mounting bracket from the rear of the
Touch Panel.
3.4 Remove the faceplate from PIXIE Touch Panel.

3.6 Attach the Touch Panel main body onto the mounting
bracket, use the hook on the mounting bracket to fix it securely
in place.
3.8 The installation is completed. Please follow the on-screen step-by-step guide to complete the setup once powered. The
Touch Panel may take up to 60 seconds to be ready for configuration after being powered.
* If the connection of a LAN cable is not feasible for the installation environment, the PIXIE Ambience Touch Panel supports 2.4GHz Wi-Fi
for wireless network connection. In this scenario, please ensure the Wi-Fi signal coverage, and set up the network connection for the
touch panel on the screen interface after installation.
3.5 Connect power and network (LAN cable* recommended) to the touch panel main body.
Option 2 - PoEOption 1 - DC 12V power supply (min. 15W)
LAN Cable
Constant Voltage
Power Supply
Output: 12V DC
Power rating: 15W or above
Power Supply
LAN Cable
3.7 Mount the faceplate onto the touch panel main body.

4.1 The four multifunction buttons
There are four physical buttons accessible from the front of the touch
panel. They are for rapid access to commonly used devices, groups
and scenes throughout the PIXIE smart home. The configuration can
be finalised on the touch panel interface via Settings->Multifunction
buttons. See below tables for operations of these buttons when
configured for different functions.
4.2 Restart
Make sure the Touch Panel is powered. Remove the faceplate, using the
pin key provided in the pack, insert it gently into the hole indicated as
RESTART on the top of the touch panel main body, and click the button
once. The touch panel will restart.
4. Operations
Operations when configured to control a device
Operations when configured to control a group
Operations when configured to control scenes
1 Click
2 Clicks
Activate scene 1
Activate scene 2
Operation Result
1 Click
2 Clicks
Turn ON/OFF.
When turning the light on, it will
work on the last used brightness
setting
Turn ON/OFF.
When turning the light on, it will
work on the last used brightness
setting
Turn ON/OFF.
When turning the light on, it will
work on the last used brightness
setting
Shortcut to the maximum
brightness
Shortcut to the maximum
brightness
Shortcut to the maximum
brightness
3 Clicks
Long Press
Switch to the next color
temperature, which circulates in
Warm White->Cool White->
Daylight. For S9842 downlight
Switch to the next color. Color
circulates in
White->Red->Green->Blue. NA
When the light is on, long press
the button to dim up or down,
release the button to stop.
When the light is off, long press
the button to turn on the light at
minimum brightness and
increase brightness, release the
button to stop.
When the light is on, long press
the button to dim up or down,
release the button to stop.
When the light is off, long press
the button to turn on the light at
minimum brightness and
increase brightness, release the
button to stop.
When the light is on, long press
the button to dim up or down,
release the button to stop.
When the light is off, long press
the button to turn on the light at
minimum brightness and
increase brightness, release the
button to stop.
Operation
Paired device
PIXIE
Smart Dimmer
PIXIE
Smart RGB Strip, RGB Strip
Controller
PIXIE
Smart Single Color Strip,
Single Color Strip Controller
Shortcut to the maximum brightness Dimmable product group only
Dimmable product group only
Switch colour/colour temperature
Switch colour/colour temperature
Subject to the product group functionality
Turn ON/OFF the Group
2 Clicks
3 Clicks
Long Press
NA
1 Click
Result Remark
Operation

1) The product wireframe drawings in this document
are intended for illustration purposes only and may
differ from the final physical product.
2) The installation instruction is subject to change
without prior notice.
3) NO DIY, installed by a licensed electrician only.
Due to continued product and information updates, product data included herein shall not form part of any contract and or technical
performance guarantee unless expressly confirmed in writing by SAL at the time of order.
SAL National Pty Ltd. 40 Biloela Street Villawood NSW 2163
ABN 21 633 189 474
4.3 Reset
Resetting the device will return it to its default settings / factory settings and
users will need to follow the Touch Panel setup procedure again.
Make sure the touch panel is powered. Remove the faceplate, using
the pin key provided in the pack, insert it gently into the hole indicated as
SET on the top of the touch panel main body, press and hold the button for
15 seconds until the screen turns off, then release. This is a factory reset, all
the data will be cleared and the Touch Panel can be reconfigured again.