Q-BASE LED LINEAR HIGH BAY
English
ASD LIGHTING CORP
Web site: www.asd-lighting.com
For most up-to-date spec sheets please refer to asd-lighting.com
The distance between the antenna and
the glass (dielectric material) should be
no less than 13mm when the sensor is
within the glass lampshade. Otherwise,
the microwave motion sensor will not
penetrate the glass easily.
13 mm
glass lamshade
sensor
Avoid placing the sensor inside a metal
chamber, this may cause a mis-trigger.
metal chamber
sensor
To avoid blocking the microwave
emission, the microwave sensor can
not be covered with metal materials,
be sprayed with a coating of metal
components, or have attached metal
material or stickers etc.
metal
sensor
The sensor should not be placed in a small
conned space. To avoid increasing the sensor
detection range or abnormal operation, the
sensor should be kept away from large areas of
metal and glass reectors (separation distance
at least 1m). Reduce the detection area setting
or contact Merrytek for more help.
metal reflector
sensor
1 m
1 m
When multiple sensors
are installed side-by-side
in the same direction, the
distance between each
sensor should be kept at
least 1m (the warehouse
sensors at least 3m) to
avoid mutual interference.
Any vibration or movement may
trigger the sensor. Ensure the
sensor is far from any constant
movement.
To avoid aecting the microwave
signal transmission, the microwave
antenna should be higher than the
surrounding metal surface. metal metal
metal metal
sensorsensor
vibration elevator
sensorsensor
1 m 1 m 1 m
multi sensors are installed in the same direction
multi warehouse sensors are installed in the same direction
sensor sensor sensor sensor
3 m 3 m 3 m
sensor sensor sensor sensor
REMOTE CONTROL sold separately:HD05R
Scene
Apply
Hold time
Detection range
Daylight sensor
Stand-by dimming Stand-by period
Memory
MW/PIR
Start
POWER
%
Test
(2S)
Button Remarks Button Remarks Button Remarks
ON/OFF Turn ON or OFF the sensor. Apply Apply Press to apply the preset program to
the specic sensors. Hold time
The period that light will stay illuminated
100 % aer no motion’s detected;
Use this button and the + - buttons
to adjust.
MW/PIR Select Microwave
or PIR sensor
Switch between Microwave sensor and
PIR sensor models
Detection
range
Also known as "sensitivity", 100 %
means the highest sensitivity and
longest distance. Use this button and
the + - buttons to adjust.
Stand-by
period
The period aer holdtime, during which
the light keeps standby dimming level;
Use this button and the + - buttons
to adjust.
Scene Scene
Press to begin detection programming.
Before pressing any other buttons, the
screen shows default programming
(Detection area 100 %, Holdtime 5 s,
Daylight disable, Standby dimming 10
%, Standby period 0 s).
Stand-by
dimming
Aer hold time, the light will dim from
100 % to optional standby dimming
levels;
Use this button and the + - buttons
to adjust.
Daylight
sensor
The preset lux level at which motion will
be detected. Use this button and the + -
buttons to adjust.
Start Start
Press before you try to save the
program into the remote. Aer pressing
it, the S on the screen will blink
repeatedly while saving the program.
UP
The main functional buttons to adjust
the factors to desired level.
Test
(2S) Test
mode
Press this button to test the sensor; it
will temporarily change the hold time to
2s. This setting cannot be saved.
Memory Memory
Press aer programming, the blinking
S will become a solid M, which means
the program has been saved.
DOWN POWER
%Power
The dimming output in detection mode.
Use this button and the + - buttons
to adjust.
Memory and apply:
1. ON/OFF button to turn on the light.
2. SCENE button to start programming.
3. START button.
4. Press the Detection Area button, the icon will blink on the LCD screen, use the
+ - buttons to adjust.
5. Use the same process to change the hold time, standby dimming level, standby
period, and daylight threshold.
6. MEMORY button.
7. APPLY button.
Sensor programming:
1. ON/OFF button to turn on the light.
2. SCENE button to start programming.
3. Press the Detection Area button, the icon will blink on the LCD screen, use the
+ - buttons to adjust.
4. Use the same process to change the hold time, standby dimming level, standby
period, and daylight threshold.
* Icon will blink for 5s meaning the program has been saved.
* When a button is pressed, the light will signal remote connection by dimming and then
resuming 100%.
* Number on LCD screen display may keep changing 10 %-100 %.
Manual dimming:
ON/OFF mode:
1. ON/OFF button to turn on the light.
2. Press + - button to dim light directly, it dims from 10 % to 100 % while in
dimming mode.
Manual dimming:
Motion sensor mode:
1. ON/OFF button to turn on the light.
2. SCENE button to start programming.
3. POWER button.
4. Use the + - buttons to dim light, the light will only dim down to 60%, anything
less will only be a standby dimming level option.
