Lightolier POWERSPEC 7218HT series User manual

—
—
/INSTRUCTION SHEET NO.
INSTALLATION OF PRE-WIRED QUAD TUBE POWERSPEC”
ELECTRONIC COMPACT FLUORESCENT REMODELER KITS
7218HT AND 7226HT SERIES (2 PIN QUAD TUBE) IS:7226HRM
7218HF AND 7226HF SERIES (4 PIN QUAD TUBE) RI 293 Page 1of 2
READ AND UNDER~AND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these Instructions for maintenance reference.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: WHEN USING ELECTRICAL EQUIPMENT BASIC SAFETY PRECAUTIONS MUST
ALWAYS BE OBSERVED INCLUDING THE FOLLOWING:
●TO PREVENT ELECTRICAL SHOCK, TURN OFF ELECTRICITY AT ELECTRICAL PANEL
BEFORE PROCEEDING.
●RISK OF ELECTRIC SHOCK. TO PREVENT ELECTRIC SHOCK, FOR PROPER OPERATION
AND SAFETY, THIS FIXTURE MUST BE GROUNDED.
●THIS FIXTURE IS INTENDED FOR INSTALLATION IN ACCORDANCE WITH NATIONAL
ELECTRIC CODE AND LOCAL REGULATIONS.
●TURN OFF POWER BEFORE I,AMPING AND RELAMPING.
-Donot install fixture on abranch circuit having aGround Fault Circuit Interrupter (GFCI). Typically
electronic ballasts may cause GFCI tripping.
WARNING—(RWK OF FIRE) DO NOT INSTALL INSULATION WITHIN 3INCHES OF FMTUF?ESIDES OR
WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH AMANNER TO ENTRAP HEAT
EXISTING CONSTRUCTION
=& p~@n
FIG.AFIG. BFIG. CFIG. DFIG. EFIG. F
LCUT OPENING U. WIRE-IN Ill. AllACH J-BOX IV. AITACH V. SNARON VI. PUSH-UP
CUT OPENING (Fig. A) MOUNTING RING
Use MOUNTING RING provided as atemplate to
cut ahole in the ceiling. Use inside diameter to
scribe hole.
.WIRE-IN (Fig. B)
Wire to supply leads. (For Cable, use built-in Cable
Clamp in J-BoxJ White fixture lead to neutral supply RING
lead. B!ack fixture lead to hot (120V)supply lead.
Bare fixture wire to supply ground. Use wirenuts
(local hardware item). Place all electrical
connections in the J-BOX. Attach J-BOX COVER J-BOX
onto J-BOX.
1.ATTACH J-BOX (Fig. C & G) NA
1. Attach J-BOX PIJ4TEto ceiling by pushing NAIL LO
TAB on J-BOX PIATE into ceiling, Fig. G.
2. Push LONG LEG of NAIL CLIPS (supplied in
parts bag) into RAISED BUMP of J-BOX PIATE
and SHORT LEG into ceiling, Fig. G.
3. Make sure that the J-BOX PLATE is securely
attached to the ceiling and the J-BOX is in the OPENING IN CEILING
position shown in Fig. G. FIG. G
1- I<*HTC> LBE1?”;?t;Z;f;,N2;;;l;,EZ;;Y

Iv.
INSTALLATION OF PRE-WIRED QUAD TUBE POWERSPEC”
ELECTRONIC COMPACT FLUORESCENT REMODELER KITS
7218HT AND 7226HT SERIES (2 PIN QUAD TUBE)
7218HF AND 7226HF SERIES (4 PIN QUAD TUBE)(CONTINUED)
A7TACH MOUNTING RING
Insert MOUNTING RING into CEILING as shown
(Fig. H).
1. In order to install SIDE MOUNTED type
REFLECTORTRIMS when the ceiling thickness
is greater than 1‘<the additional ceiling material
opposite the JUNCTION BOX must be removed
(Fig. K.)
2. Inseri REFLECTOR TRIM, SOCKET CUP first
into ceiling opening where the material was
removed opposite the JUN~lON BOX. Pivot the
REFLECTORTRIM and push it up into the
ceiling (Fig. K.)
CLIP ASSEMBLY (Fig. 0
1. Insert CLIP from inside housing, through ‘T slot.
2. Apply downward force with screwdriver on top of
CLIP or engage screwdriver in slot in CLIPS flange.
3. Apply force until CLIP is snugly seated.
CLIP REMOVAL (Fig. J)
3. Insert asmall blade, short-handled screwdriver
through the CLIPSS screwdriver slot, and press
against the opposite side of the CLIF?
2. Push CLIP up to top of “T” SLUT and remove.
V. SNAFON (Fig. E)
1
SEE SEPARATE
REFLECIUR TRIM
INSTRUCTION
VI. PUSH-UP (Fig. F) SHEETS.
/r JUNCTION BOX
I
CEIL
.-1
2“ MAX.
—7
I
f“=- REFLECTOR
TRIM
I
N
P
u
T
/FIG. K
WIRHIJGDIAGRAM FOR 2PIN BASE LAMP
r— BLACK >
NEUTflAL
(wH!TQ 1~WHITE -1
WHITE
I&n —w~ucx
L- —
T
ILI
I
BALLASTCASE MUST BE GROUNDED LAMPS
IS:7226HRM
RI 293
Page2of 2
SLOT
RING
FIG. H
TO INSERT
Y
1;::;:;
f+ STEP 1
‘1
I
‘T” SLOT SHORT HANDLE
SCREWDRIVER
4/%
---- STEP 2
CEILING \1+ STEP 3
/f ‘i\ )..’. : ,;. .
\
‘d CEILING
FIG. I
1! TO REMOVE AIREMOVAL
—.——
\\
FIG. J
WIRING DIAGRAM FOR 4PIN BASE LAMP
,E.TRAL..+~-
RED
[
IRE9
NW2Low YELLOW
CMKTE1
+.L Zr o
YEUBLK
PvELLm YE”BLK
HOT YELLOW
u(BL4CKI BLUE
Te4uE c~
!+
L—. +—
ILAMPS
BALLAST CASE MUST BE GROUNDED
—
WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGNTOLIER INC. USE OF OTNER MANUFA~RERS’
REFLECTOR TRIMS VOIDS TNE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE AFIRE