ASEPT nemco UNI-2 User manual
UNI DISPENSERS
User Manual MODEL UNI-2, UNI-3
10950, 10951
UNI Dispensers
Complete Pump 9851(Natural Dome)
Complete Pump 9855(Black Dome)
2
Natural Dome
7299
Brush
7615
Designed for use with standard 1½ ,1 or
/ gallon pouched condiments and toppings.
Pumps attach to 16mm tments in pouches.
Valve
9683
Dome Clip
7868
Pump Housing
9720
Nozzle
8651
Black Dome
8215
3
Safety
Pump Cleaning
All pump components are
dishwasher safe.
Disassemble all ve (5) parts.
Clean with soap and hot water,
rinse, sanitize and dry parts
according to local sanitization
requirements.
Use supplied brush to scrub
inside parts.
Clean and sanitize exterior of shroud as needed.
All components must be cleaned
before rst use.
According to food and safety
regulations, most foods must be
stored and/or served at certain
temperatures or they could
become hazardous. Check with
local food and safety regulators
for specic guidelines. Be aware
of the product you are serving
and the temperature the product
is required to maintain.
IMPORTANT Clean, rinse, sanitize,
and dry parts at a minimum
of every 24 hours. Always
comply with local sanitization
requirements.
4
Assembly
onto the end of the pump housing.
Bend the outer portion of the nozzle
inside out.
Insert into opening. Tab of nozzle faces
towards housing. Flip the outer portion of
the nozzle over the end of tube.
Mount the nozzle
into the pump housing.
Ensure the aps slide into place.
Press the entire dome rmly, including the
top portion.
Insert dome
2
over the dome and pump housing.
Ensure that the tab on bottom of the dome
slides into the opening in the dome clip.
Insert the dome clip
3
1
5
Put new pouch on
countertop with tment
facing up. Place piercing
end of connector in cen-
ter of the tment. Push
rmly until pump snaps
into place. Hold pouch
up and push dome to
prime pump.
Connect pump to pouch
5
into the dispenser shroud. Hold end of
pouch up while guiding the pump into
the slots inside the front of dispenser.
Suspend top of pouch with clip
inside shroud.
Insert pouch and pump
6
into the bottom of the pump housing.
Wrap the aps on the side of valve onto the
pair of pegs on the pump housing.
TIP: Lubricate parts with clean water to
ease tting.
Insert valve
4
6
8Press the pump lever several times until
food is visible in discharge tube.
Prime pump
Tips & Troubleshooting
Ensure that you hear a CLICK when attaching pump to pouch.
Prevent leaks:
Ensure that dome is pushed fully into pump housing.
Pro Tip: Clean water may be used as lubrication
when tting valve onto pump housing.
Product not dispensing?
Make sure dome is primed properly.
7Hold the lever up while
inserting lid tabs into
slots in back of
dispenser shroud.
Insert the lid
1
7
Use a athead screwdriver to pry
o the locking washer from the
pin at the end of the link arms.
Keep locking washer for step 4.
Remove locking washer
2
Slide the pin out from the pair of
link arms and handle holes.
Remove pin
4
Select portion setting
with holes for desired portion
setting. Slide pin through all.
Secure pin with locking washer.
Align holes on
handle and link arms
3
Setting the Portion
A
Link Arm Position
B
C
3
2
1
Handle
Position
Link Arm
Position
A
A
B
A
B
C
C
B
C
Handle
Position
1
2
1
3
2
1
2
3
3
Portion
(ml)
52.0
39.0
30.0
22.5
19.5
15.0
7.5
7.5
1.0
Portion
(. oz.)
1.75
1.33
1.00
0.75
0.66
0.50
0.25
0.25
0.03
8
ASEPT General Warranty
Liability for defects
Should the products, as delivered, within one
(1) year from delivery be shown to be defective
due to defaults in material or manufacturing
(“Warranty Period”), the Supplier undertakes,
at its own option (i) to make a replacement
delivery, (ii) to repair or rework the products
claimed to be defective or (iii) to accept return
of such product and refund such proportion of
the purchase sum received as corresponds to
the returned products. The Supplier assumes
no liability for defects as regards to layout and
design of the products, unless expressly stated in
the Agreement.
The Customer shall without undue delay
notify the Supplier in writing of any defect
which appears. Such notice shall under no
circumstances be given later than two (2) weeks
after the expiry of the Warranty Period.
The Supplier is liable only for defect which appear
under the conditions of operation provided for
in the Agreement and under proper use of the
product. The Supplier’s liability does not cover
defect which are caused by faulty maintenance,
330021 07/21
incorrect erection or faulty repair by the Customer,
or by alterations carried out without the Supplier’s
consent in writing. Finally, the Supplier’s liability does
not cover normal wear and tear or deterioration.
Except as expressly specied above, the Supplier has
no liability for defects in the products whatsoever
and are under no circumstances responsible for any
direct or indirect losses, damages or costs incurred
by the Customer, including consequential damages.
General limitation of liability
Notwithstanding any other limitation of liability
mentioned in the Agreement including these
Terms and Conditions, the Supplier’s liability for
damages under the Agreement shall be limited to
the insurance compensation that can be obtained
in accordance with the Supplier’s each valid liability
insurance.
Consequential losses
There shall be no liability of either party towards the
other party for loss of production, loss of prot, loss
of use, loss of contract or for any other consequential
or indirect loss whatsoever.
Caution:
Modifying this device can
produce unintended
consequences.
NOTE: This equipment has been tested
and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communi-
cations. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Asept International AB
Traktorvägen 17, SE-226 60
Lund, Sweden
+46 46 329 700
Asept International Inc.
900 Oakmont Ln, Suite 207,
Westmont IL 60559, USA
+1 (630) 441-5656
www.asept.com
Nemco Food Equipment
P.O. Box 305
301 Meuse Argonne
Hicksville, OH 43526
800.782.6761
www.nemcofoodequip.com
Available In the USA through:
This manual suits for next models
3
Table of contents
Other ASEPT Dispenser manuals
