TAKE-A-LABEL TAL-450-SS User manual

Operating
Instructions
General Specications, Stainless Steel Dispensers
General Specications,
Model 450SS
Size (Approx.):
14.58W x 12.38H x 18.50D
Shipping Weight:
24 lbs (10.9 KG)
Electrical:
110/120VAC, 50/60HZ,
4 AMP FUSE
take-a-label.com • [email protected] • 16900 Power Dr., Nunica, MI 49448 • 616.837.9300
Note: e TAKE-A-LABEL dispenser is shipped
mounted to a base to prevent shiing in the container.
1. Remove the machine from the base.
**Always load the TAKE-A-LABEL dispenser
with the On-O switch in the (OFF) position.**
2. To load a roll of labels on the TAKE-A-LABEL,
loosen the unwind hub screw (57) on the unwind
collar (56) and remove the collar, unwind washer,
unwind spring, and disc from the unwind sha.
3. Place the roll of labels on the unwind sha
between the two unwind discs. Place the roll with
the beginning of the roll on the bottom with the
web dispensing to your right as you face the side
of the machine.
4. Replace the unwind disc, unwind spring, and collar
onto unwind sha. If using labels on a 3” diameter
core, the hub on each disc will t inside the core
and support the roll of labels. If the labels are on a
1” core, simply slide the disc up snugly against the
roll of labels. When the disc is in place, tighten the
unwind hub screw against unwind sha.
5. read the loose end of the labels under and up the
front of the peel plate.
6. Pull the labels over the top of the peel plate far
enough to reach the waste take-up roll.
7. Remove the waste wind clip, thread the label
backing paper under the clip, and reinsert clip
over loose paper.
8. Position the Photo Eye by loosening the wing nuts
and moving assembly to the right or le, so the
sensor is at or near the center of the labels. e
Photo Eye can be tilted forward or backward by
loosening the mounting bracket’s vertical
adjustment wing nut.
9. Turn on the On-O switch. e waste wind sha
will turn, winding up the backing paper and
dispensing a label at the top of the peel plate. When
the Photo Eye senses the dispensed portion of the
label, the motor will stop. As each label is removed,
the machine will operate until the next label is in
position to be removed. (CAUTION:) Turn o
switch before removing wound up waste.
10. If the labels tend to follow the backing paper over
the top of the peel plate instead of peeling o, then
there is insucient tension on the web of the labels.
e sha adjustment collar should be moved in to
put more tension on the web.
11. If the motor stalls it may be necessary to move
the sha collar out to reduce the amount of
unwind tension.
Operating Instructions for the TAKE-A-LABEL Stainless Steel Label Dispenser
Model TAL-450-SS Shown
Model TAL-450-SS Shown

1 25109-SS, TAL-250 Unwind Sha TAL-250 Size 1
1 45109-SS, TAL-450 Unwind Sha TAL-450 Size 1
1 72609-SS, TAL-750 Unwind Sha TAL-750 Size 1
2 25201-SS, 250, 450, 750 Main frame 1
12 45182, Washer, nylon 5
13 45181-SS, Carriage Bolt 2
14 45180-SS, Wing Nut 5
16 30653-SS, 1/2-13x.75 BHCS 1
17 72618, Felt Washer 1
18 45136, Unwind Disc 2
19 10-32x0.5 BHCS 5
20 10-32x0.375 BHCS 10
21 25202-SS, 250, 450, 750 Motor housing 1
22 25203-SS, 250, 450, 750 Rear/side cover 1
23 40007, Power On/O switch 1
26 81912, Small cord grip 1
27 76800, Gear Motor 1
28 45133, Name Plate Label 1
30 10-32 Hex Nut 8
31 45100, PCB - 250, 450, 750 DV 1
32 6-32x0.25 BHCS 5
33 45102, Control Board - 450, 750 CS Optional: Used with Special DC Photoeyes 1
34 30202, Label Counter Optional: Label Counter 1
35 25211, IEC Outlet 1
Not Shown 25212, IEC Line cord, US Not Shown 1
37 25213, Photoeye Photo Eye Label Sensor 1
38 81904, Photo eye Ring Nut Photo Eye Label Sensor 2
39 25204-SS, Photo eye bracket Photo Eye Label Sensor 1
40 45186, P-clip 1
56 26001-SS, Sha Collar 1
57 26002-SS, Knob 1
58 25112, Washer 1
59 25116-SS, TAL-250 Peel Plate TAL-250 Size 1
59 45111-SS, TAL-450 Peel Plate TAL-450 Size 1
59 72612-SS, TAL-750 Peel Plate TAL-750 Size 1
60 25114-SS, TAL-250 Waste Rewind Sha TAL-250 Size 1
60 45112-SS, TAL-450 Waste Rewind Sha TAL-450 Size 1
60 72613-SS, TAL-750 Waste Rewind Sha TAL-750 Size 1
61 25115, Waste Wind Clip TAL-250 Size 1
61 45131, Waste Wind Clip TAL-450 Size 1
61 72610, Waste Wind Clip TAL-750 Size 1
62 25113-SS, Unwind Spring 1
Common Parts for Prior Model Years
Not Shown 45208, Trip Wire 2014 and Older Models 1
Not Shown 45309, Switch Assembly 2016 and Older Models 1
Not Shown 81905, Photo Eye 2016 and Older Models 1
Not Shown 81906, Relay 2016 and Older Models 1
Not Shown 81907, Relay Socket 2016 and Older Models 1
Not Shown 25119, Lighted On/O Switch 2007 and Older Models 1
Not Shown 45217, Power Cord 2016 and Older Models 1
Not Shown 45153, Power Cord Clamp 2016 and Older Models 1
Not Shown 45155, Fuse Holder 2016 and Older Models 1
Not Shown 45157, Fuse 2016 and Older Models 1
TAL 450SS Label Dispenser Exploded View ITEM# PART NUMBER NOTES QTY.
AND DESCRIPTION