Asgard Bike Locker User manual

' BIKE LOCKER'
PACK CONTENTS
ITEM
NO
PART
DESCRIPTION QTY
1.1
2
3
4
5
6
42486 LH
DOOR FRAME ASSY
1200mm*900mm
2
1
1
1
2
7
8
9
1
1
1
ASGARD
BIKE LOCKER
SELF ASSEMBLY INSTRUCTIONS
PLEASE NOTE FOR SAFETY REASONS THE
ASSEMBLY OF THIS UNIT REQUIRES
TWO PEOPLE.
BASE INSTRUCTIONS
A FIRM, LEVEL ,FLAT SURFACE IS
REQUIRED AS A BASE FOR THIS UNIT
SUCH AS CONCRETE OR FLAGS.
- MINIMUM BASE MEASUREMENT
FOR BIKSTORE IS 1000W*2000L
TOOLS REQUIRED
- POSI-DRIV SCREWDRIVER
(POWER DRIVER RECOMMENDED)
4mm ALLEN KEY
10mm SPANNER
- 6mm DIA MASONRY DRILL
- 13mm SOCKET SPANNER
(FOR ANCHOR FIXINGS)
DOOR ALLIGNMENT & ANCHORING
OF UNIT
IT IS IMPORTANT TO CORRECTLY LEVEL
THE UNIT USING THE PACKING PIECES
PROVIDED, ONCE ASSEMBLY IN
ACCORDANCE WITH THE INSTRUCTIONS
OVERLEAF IS COMPLETE AND PRIOR TO
FIXING THE UNIT TO THE GROUND.
- SLIDE THE PACKING PIECES UNDER THE
CORNERS OF THE UNIT AS
REQUIRED UNTIL AN EQUAL GAP HAS
BEEN ACHIEVED AROUND THE DOOR
ALLOWING FOR SMOOTH
OPERATION & ALLIGNMENT.
- DRILL THROUGH THE EIGHT HOLES
IN THE BASE OF THE UNIT USING
6mm DIA MASONRY DRILL TO A DEPTH
OF 70mm.
- SCREW IN THE ANCHOR FIXINGS.
(THESE HAVE A SELF CUTTING THREAD)
PLEASE SEE OUR WEBSITE FOR DETAILS
OF MAINTENANCE OF THIS PRODUCT
WWW.ASGARDSSS.CO.UK
42172
SIDE PNL
1800*1125
42171
BACK PNL
1125*878
42170
TOP PNL
1800*900
42397
TOP STIFFENER
870*100
42655
FIXING CHANEL
1740*42
42472
WHEEL GUIDE
1800*120
42176
LH WHEEL GUIDE
750*20
ZSCREW100
No10*5/8 S/TAPP
ZSCREW254 ZSCREW32
M6*6 PAN HEAD M7.5*60 ANCHOR BOLT
ZCOMPPLAS22,23,24
2mm,3mm,5mm PACKERS
ZCOMPPLAS02
SELF SEAL
PLUG
68 84 + 4 + 4
QTY 8
42177
RH WHEEL GUIDE
750*20
66
ZHWNUT42
M6 HEX LOCK NUT
FIXING PACK
10 2
10
35190
UNIVERSAL HOOK
4
5
2
7
89
6
32
42485 RH
DOOR FRAME ASSY
1200mm*900mm
1.2
ONE PART
ONLY
DEPENDS ON
HANDING OF
UNIT
(LH PART
SHOWN)
SEALENT
1
DRG No 042487

L
M
S
T
U
PARTS INSTRUCTION
POSITION FRAME 1 APROXIMATLEY IN ITS
REQUIRED POSITION, OFFER UP SIDE PANEL 2
ENSURING HOLES ARE ALIGNED
SCREW THE PANELS TOGETHER.
10*
PARTS INSTRUCTION PARTS INSTRUCTION
10* 20*
PARTS INSTRUCTION
INSTRUCTION
INSTRUCTION
INSTRUCTION
INSTRUCTION PARTS
PARTS
PARTS
PARTS
STEP 1 STEP 2 STEP 3 STEP 4
STEP 5 STEP 6 STEP 7 STEP 8
10*
24* 2* 2*
DOOR AND FRAME
SIDE PANEL 1 & 2 OFFER UP BACK PANEL 3
ENSURING HOLES ARE ALIGNED
SCREW THE PANELS TOGETHER.
BACK PANEL 3 OFFER 2ND SIDE PANEL 2
ENSURING HOLES ARE ALIGNED
SCREW THE PANELS TOGETHER.
SIDE PANEL 2 FIXING CHANNEL 6
2 off
HOOK FIXING CHANNELS 6 OVER THE BOTTOM BEND
OF SIDE PANEL AS SHOWN IN DETAIL *A* FIX IN PLACE
WITH SCREWS
42170 TOP 4
42397 TOP
STIFFENER 5
POSITION TOP PANEL 4 INTO PLACE ( SHORT SIDE TO FRONT)
ONTO ASSEMBLED SIDES AND BACK
FROM INSIDE FIT STIFFENER 5 INTO CENTER OF TOP
AND FIX WITH SCREWS LEAVING OUT THE 2ND AND 3RD SCREWS
FROM THE FRONT
LEAVE OUT 2ND AND 3RD
SCREWS UNTIL LATER
FIXED WITH CENTER SCREWS
WHEEL GUIDE 7
UNI HOOK 10
2off
CLIP WHEEL GUIDE 4 INTO POSITION
DOOR END FIRST( INTO RAIL) THEN INTO
SLOTS ON BACK PANEL
SCREW HOOKS 10 INTO REQUIRED POSITIONS
LH & RH 8 & 9
WHEEL GUIDES
SLOT LH & RH WHEEL 8&9
GUIDES INTO CENTER GUIDE
BOLT INTO POSITION
BOLT ON OUTSIDE NUTS ON IN SIDE
FIT 8 PLUGS INTO HOLES ON OUT SIDE OF END PANELS
(HOLES CAN BE USED TO FIX 2 UNITS SIDE BY SIDE)
LEVEL UNIT USING PACKERS SUPPLIED
FIX DOWN USING SELF CUTTING ANCHOR BOLTS
3 DOWN EACH SIDE 2 INTO GUIDE CHANNEL
FOR THIS YOU WILL NEED TO USE A 6mm
MASONRY DRILL DRILLING 70mm DEEP
THOUGH HOLES IN THE RAILS
SEALENT IS REQUIRED
HERE AT THE BACK OF
THE DOOR FRAME.
*A*
PRIOR TO FITTING ROOF PANEL APPLY
A CONTINUOS BEAD OF SEALENT ALONG THE
SIDES, BACK AND OVER THE DOOR FRAME
ALONG THE ROOF JOINT.
REMOVE ANY EXCESS SEALENT ALONG THE JOINT ENSURING
THAT THE SEAL IS COMPLETE.
DRG No 042487

900,00 1900,10
1200,00