ISSI SMALL PARTS KIT User manual

SMALL PARTS KIT INSTRUCTIONS
6400 West 105th Street Minneapolis, MN 55438 www.rideissi.com
5463 01/14
THANK YOU FOR PURCHASING ISSI SmAll PARTS KIT!
At iSSi™, we know the best way to improve a bike is to make it truly your own.
That’s why we fashion equipment to personalize the connection between you
and your bike. iSSi: it’s your bike; make it yours.
WARNING: CYCLING CAN BE DANGEROUS. BICYCLE PRODUCTS SHOULD BE
INSTALLED AND SERVICED BY A PROFESSIONAL MECHANIC. NEVER MODIFY
YOUR BICYCLE OR ACCESSORIES. READ AND FOLLOW ALL PRODUCT
INSTRUCTIONS AND WARNINGS INCLUDING INFORMATION ON THE
MANUFACTURER’S WEBSITE. INSPECT YOUR BICYCLE BEFORE EVERY RIDE.
ALWAYS WEAR A HELMET.
WARNING: A loose, cracked, worn out, or crashed pedal can come off
of your bicycle crank leading to a loss of control that could cause serious injury.
Pedals that are damaged or worn out should not be used. Remove immediately
and inspect for damage. If you are unsure if your pedal is safe to ride, consult
your local bicycle dealer.
WARNING: Never ride in open-toed or open-heeled shoes as they don’t fully
support and secure your foot. Doing so could lead to a loss of control and serious
injury and/or death.
For additional product and safety information go to: www.rideissi.com/safety.
COmPATIBIlITY AND INTENDED USE
iSSi cleats and pedal parts are only designed as replacement parts for iSSi
pedals. iSSi cleats are compatible with all standard 2-bolt SPD shoe drillings.
The parts kits and cleats are NOT INTENDED for anything other than direct
replacement of parts.
WARNING: Do not attempt to modify or alter your iSSi pedals or cleats.
TOOlS AND SUPPlIES
2.5, 3mm Allen wrenches
#10 Torx wrench
Red Loctite
Grease
NOTE: Never use a cone wrench to remove or install a pedal.
NOTE: Pedal threads are different from left side and right side. The right-side
pedal has a right-hand thread (removes counterclockwise, installs clockwise).
The left-side pedal has a left-hand thread (removes clockwise, installs
counterclockwise). Additionally, the thread will appear to slope up toward
its tightening direction. Left-hand threads slope up to the left, while right-hand
threads slope up to the right.
TO REPlACE THE PEDAl RETENTION ClIPS AND STRIKE PlATES
1. Loosen the 3mm clip tension bolts (item #7) fully. THEY DO NOT COME
COMPLETELY OUT OF THE RETENTION CLIP.
2. Use a T10m Torx to loosen the Torx screws and remove the front retention
clips (item #1) on both sides of the pedal and the strike plates (item #4).
3. Apply a small amount of red Loctite to the threads of the T10 Torx screws
(items #2 and #3) and reinstall the new retention clips (item #1) and strike
plates (item #4) to the pedal, tightening the screws to 3Nm.
4. TURNING CLOCKWISE, loosen the 2.5mm spring retention bolts (item #5)
from the inside of the pedal body. Remove the old springs and retention
adjustment clip.
5. Place a new spring retention bolt (item #5) through the bolt hole on the side
of the pedal just enough for the bolt to come through.
6. Place the new retention adjustment clip (item #6) inside the pedal body and
slide the spring retention bolt through the retention adjustment clip just
enough to go through the hole.
7. Slide the spring retention bolt through the springs (item #8).
NOTE: The springs have a LONG EAR and SHORT EAR. The LONG EAR should
be pointed down and against the spindle body, and against the adjustment
screw plate (item #9). The SHORT EAR should be pointed up and away from
the spindle body, and against the adjustment screw plate.
8. Finish threading in the spring retention bolts (item #5) and tighten to 4Nm.
9. Adjust the 3mm tension bolt (item #7) to the desired resistance.
10. Reinstall the iSSi-branded end caps and tighten to 3Nm.
ONGOING mAINTENANCE
To function properly, pedals and cleats must be kept clean. Occasional lubrication
of cleat bolts will help prevent rust and seizure. Pedals should be serviced if:
rotating pedal emits noise, rotation by hand feels rough, and/or there is play
in the bearings.
1
2
3
10
4
11
5
6
8
9
7
Figure 1
Items 6, 7, 9 & 10
come pre-assembled
ITEm # DESCRIPTION QUANTITY
1 Retention Clips 4
2, 3 T10 Torx Screws 16
4 iSSi Branded Strike Plates 4
5 Spring Retention Bolts 4
6 Retention Adjustment Clips 4
7 Clip Tension Bolts 4
8 Springs 8
9 Adjustment Screw Plates 4
10 Screw Seal 4
11 iSSi Branded End Caps 2

SMALL PARTS KIT INSTRUCTIONS
6400 West 105th Street Minneapolis, MN 55438 www.rideissi.com
5463 01/14
lImITED WARRANTY
This iSSi product is warranted against defects in materials and workmanship for
three (3) years from the date of retail purchase of the product, subject to the
limitations detailed below. Save your dated receipt for proof of purchase.
This warranty does NOT cover the following:
• Damage due to improper assembly or follow-up maintenance or lack of skill,
competence or experience of the user or assembler
• Products that have been modified, neglected, used in competition or for
commercial purposes, misused or abused, involved in accidents or anything
other than normal use
• Damage or deterioration to the paint, surface finish, aesthetics or appearance
of the product
• Normal wear and tear
• Labor required to remove and/or refit and re-adjust the product within the
bicycle assembly
• Installation of components, parts, or accessories not originally intended use
with or compatible with iSSi products
This limited warranty is expressly limited to the repair or replacement
of a defective product, at the option of iSSi, and is the sole remedy of the
warranty. This limited warranty applies only to the original purchaser of the iSSi
product and is not transferable. This warranty applies only to products purchased
through an authorized dealer or distributor. In no event shall iSSi be liable for
any loss, inconvenience or damage, whether direct, incidental, consequential,
or otherwise resulting from breach of any express or implied warranty or
condition, of merchantability, fitness for a particular purpose, or otherwise with
respect to our products except as set forth herein. This limited warranty gives the
consumer specific legal rights, and those rights and other rights may vary from
place to place. This limited warranty does not affect your statutory rights.
TO THE EXTENT NOT PROHIBITED BY LAW, THESE WARRANTIES ARE
EXCLUSIVE AND THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES OR
CONDITIONS INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
WARRANTY PROCESS
We will happily back up our products if there is a problem that is our fault.
If you and your shop think your iSSi product is worthy of a warranty inspection,
please return the product to the original place of purchase, accompanied by
a sales receipt.