ASTM Mercedes-Benz G 500 User manual

User's manual
BATTERY VEHICLE
The owner's manual contains important safety information, as well as instructions
for assembly, use and maintenance.
Keep this manual for future reference.
THIS PRODUCT HAS A LIMITED 30 DAY WARRANTY
Keep the package out of the reach of children and dispose of it properly before use.
Styles and colors may vary. Made in China.
The car must be assembled by an adult who has read and understood the
instructions in this manual.
AFTER THE DATE OF PURCHASE
Mercedes-Benz G 500

SPECIFICATIONS:
suitable age:
Loading time:
64
On the purchase of your new Ride-On.
37-96 months
*
107 54 CM
carriage size
Current source:
*
Capacity of
Follow the recommendations in this manual, they are designed to improve the safety and
performance of your vehicle and its driver.
3-5km/h
load: speed:
Less than 30kg
electric charge
This vehicle will provide your child with many miles of fun.
3km/h
8-12 hours
To help ensure a safe trip for you and your child, we ask that you read this manual carefully
and save it for future reference.
2WD
1WD
About your new vehicle ÿ
6V7AH*1
12V500mA or 12V1000mA
Battery
6V1000mA
12V4.5AH *1 o 12V7AH *1
Charger
SHARE YOUR FEEDBACK ON
THIS PRODUCT ON WAYFAIR: VISIT AMERICAS TOYS
STORE ON WAYFAIR:

• Never leave child unsupervised. Direct adult supervision is required. Always
keep child in view when child is in vehicle. • Never use on highways, near
streets, motor vehicles, steps, bodies of water, inclined surfaces, hills,
wet areas, flammable vapors, in alleys, at night, or in the dark. • Never use in
unsafe conditions such as snow, rain, loose dirt, mud, sand, or
gravel; Otherwise, it may cause an unexpected accident such as rollover and
may damage the electrical system or battery. • Not to be used in traffic. • This
toy must be used with caution as skill is required to avoid falls or
collisions that cause injury to
the user or others. • This toy is not suitable for children under 36 months due
to its maximum speed; The maximum user weight is 30 kg. • This toy
has no brake.
• Non-rechargeable batteries must not be recharged.
• Rechargeable batteries must be removed from the toy before charging.
• Rechargeable batteries should only be charged under adult supervision.
• Do
not mix different types of batteries or new and used batteries. • Batteries must
be inserted with the correct polarity. • Exhausted batteries
must be removed from the toy. • The power terminals
must not be short-circuited.
WARNING! •
CHOKING HAZARD - Small parts. Not suitable for children under 36 months.
The product contains small parts, keep children away during assembly.
• ADULT ASSEMBLY
REQUIRED • Always remove protective
material and polythene bags and discard prior to assembly. • Protective
equipment must
be used. Always wear shoes and sit on the seat when operating the vehicle. •
Drive only on level ground. Never
use it on grass. • Never leave the child unattended. • Keep hands, hair
and clothing away from moving
parts.
BATTERY INFORMATION
SECURITY
The following safety hazards can cause serious injury or death:
Notice to user 2
Machine Translated by Google

19
17
3
7
10
5
21
13
14
2
6
11
1
16
15
5
9
8
4
6
12
20
7
18
Parts diagram 3
TIP: Some parts shown are assembled on both sides of the vehicle

Rear-view mirror
Key
Toolbox
vehicle body
rear wheel
Windshield
Steering wheel
rear gearbox
Front wheel
Machine screw M5x35 Ø5
nut
Ø10 washer
engine hood
Ø4x12 screw
M5x16 screw
Ø12 washer
Remote control
Screwdriver
lock nut
Charger
Seat
hubcaps
PART
NO.
R/C type para only
Left and right
1WD type only
placed on the steering wheel
Mounted on the front axle
type only
placed on the steering wheel
Mounted on the front axle
1
3
2
4
4
4
2
1
1
1
1
1
\
\
1
1
2
1
2
4
1
1
1
1
2
1
2
4
4
2
1
1
4
1
2
1
1
2
1
1
2
1
Quantity (pieces) OBSERVATIONS
Assembly Tools Required (Not Included):
2WD 1 pc labeled "R", the other one labeled "L"
2WD
1WD
1WD
Parts list 4
5
1
13
10
2
11
16
17
8
9
15
20
6
21
7
14
3
12
18
4
19
noble part

9
2 2
10
1 1
8
4 4
7
5 5
3 3
TIP: If your vehicle is a two-wheel drive type, see the next page.
Position the rear wheels 5
6
rear bottom view
1WD
10. Mount the wheel cover on the wheel.
3. Slide a Ø12 washer onto the rear axle.
6 Slide the Ø12 washer onto the rear axle (right hand side).
7. Slide the rear wheel onto the rear axle.
4. Tighten a locknut on the end of the rear axle with a wrench.
8. Slide the Ø12 washer onto the rear axle.
5. Mount the wheel cover on the wheel.
9. Tighten a locknut on the end of the rear axle with a wrench.
Remove all parts from the rear axle.
TIP: An extra wrench has been provided to hold the Locknut on the other side of the
rear axle while you tighten the Locknut on the other side.
2. Slide the rear wheel onto the rear axle. Make it match the gearbox.
1. Slide the rear gearbox onto the rear axle from the left side (gearbox labeled "R" should
fit the "R" side, gearbox labeled "L" should fit the "L" side), keep the The gearbox
connector and motor go through the larger hole and out where the battery sits.

rear bottom view
5. Mount the wheel cover on the wheels.
vehicle. Keep the motor and connector on the gearbox through the
Repeat the above procedure to mount the other rear wheel.
paired with the gearbox.
larger hole in the rear of the vehicle and out where the
Remove all parts from the rear axle.
3. Slide the Ø12 washer onto the rear axle.
find the battery
1. Slide the rear gearbox onto the rear axle. gearbox
4. Tighten a locknut on the end of the rear axle with a wrench.
2. Slide the rear wheel onto the rear axle. And keep the drive wheel
gearbox labeled "L" must fit on the "L" side of the bodywork
labeled "R" must fit the "R" side of the vehicle body; The
2WD
1
3
4
2
5
Position the rear wheels 6

bottom front view
Gap
4
2
3
5
1
5. “Snap” the wheel cover to the wheel.
3. Slide a Ø10 washer onto the front axle.
4. Tighten a locknut on the end of the front axle with a wrench.
2. Slide one front wheel onto the front axle.
After assembling any wheels on the axles, please check the
gap between the screw thread and the collapsible (refer to
the picture below), if the gap is too big, please add two or
three washers inside the wheel, but after tightening the nut
out of the wheel, please rotate the wheel with your finger to
check whether the wheel can run smoothly, this is very
important, because if the wheel can run smoothly, it is ok,
but if the nut presses the wheel and the wheel does not can
work the motor will be broken easily. Then without any
problems you need to take a shim or twooff to ensure
that the wheel can run smoothly.
1. Slide a Ø10 washer onto the front axle.
Repeat the above procedure to assemble the other normal wheel.
Remove all parts from the front axle.
Position the front wheels 7

6
4
Place the steering wheel 8
end of steering column
5
1
3
2
7
6. Align the holes in each side of the
steering wheel with the holes
in the end of the steering column.
Fit the flywheel
Remove the M5x35 machine screw and the Ø5 nut from the flywheel. Stand
the vehicle body upright.
5. Place the steering wheel on the steering column, sticking out of the center of
the steering wheel base.
4. Place the battery cover over
the battery compartment and
secure it with the screw you
removed in step one.
1. Using a screwdriver, remove
the battery cover screw located
in the center of the steering
wheel.
3. Insert 2x1.5 AA batteries in
their correct polarities
7. Tighten a nut on the
opposite end of the bolt to secure
the steering wheel to the steering
column.
2. Remove the battery cover from
the top of the
battery compartment.
TIP: If your vehicle's steering wheel is equipped with the sound feature,
follow steps 1-4 to add batteries (not included) and see battery
information on page 2.

Battery
Connect the power
supply 9
Fuse
box
2WD
1WD
1
2
1. Plug the vehicle connector into the battery connector.
White motor
connector
2. Plug the vehicle connector into the engine connector on the body as shown
above. Repeat for the other side.
red battery
connector
1. Plug the vehicle connector into the battery connector.
white vehicle connector
2. Plug the vehicle connector into the engine connector on the body as shown
above.
red vehicle
connector
rear top view

TIP: Only 1WD product need to
assemble the engine hood x4
1WD
1
1
2
2
2. Insert two M5x16 machine screws through the seat and into the vehicle body
and tighten with a screwdriver.
2. Insert two Ø4x12 screws and tighten.
1. Place the tabs on the seat back into the slots at the rear of the vehicle.
1. Place the engine cover over the engine.
Attach the engine hood and seat 10
Tabs on
seat back

Attach windshield, side mirrors, tool box 11
1
2
3
2. Place the side mirrors into the holes on the side of the doors, push
them in until you hear a "click" into place.
Press until you hear it "click" into place.
3. Place the tool box at the rear of the vehicle body.
1. Place the tabs on the windshield into the slots in the vehicle. Press until you
hear it "click" into place.

ÿ
Use your vehicle 12
V+
• To move the car, step on the pedal. •
To brake or slow down, release pressure on the pedal.
6. 3.5mm AUX input (if equipped)ÿAllow audio from your phone or portable music
player to play through the mountable speakers.
4. Sound buttons (if equipped): Press to play sound.
3. Forward/Reverse Switch: Changes the direction the vehicle is moving
5. High/Low Speed Switch (If Equipped):
1. Power button: Turns the vehicle on and off.
HINT: The vehicle is designed to operate at low speed only in
from front to back.
Operates the vehicle to move forward at high or low speed.
reverse.
2. Pedal: Supplies power (speed) to the vehicle.
• To move the vehicle forward, move the lever to the up position. • To move the
vehicle backwards, move the lever to the down position.
‹‹
abc
Use the vehicle ONLY on generally level ground! DO NOT use the vehicle on grass spaces!
STYLE II
• • Always stop the vehicle when changing speed (if equipped) or direction to avoid
damaging the gears and engine. •
HIGH SPEED (if equipped): Make sure your child knows how to drive,
how to start and stop the product and know the rules for safe driving.
1 5
1 3
6
IMPORTANT
2
4

1 2
The battery needs to be charged.
Load 13
all functions.
less than 12.5
WARNING! • ONLY
an adult can charge and recharge the battery! • • This
product with charging protection: during charging, they will be cut off
less than 6.2
6V product
12V product
battery disposal
• Use the only rechargeable battery and charger supplied with your vehicle. NEVER
• Before first use, you should charge the battery for 4-6 hours. Do not recharge the battery
replace the battery or charger with another brand. Use of another battery or charger may
cause fire or explosion. • Do not use
the battery or charger for any other product. • If you are traveling
with a digital voltmeter (IF EQUIPPED), the magnitude of the voltage will tell you how
much power is left in the battery when you need to recharge it. Make sure the vehicle
is stationary!
for more than 10 hours to prevent overheating of the charger. • When the
vehicle starts to slow down, recharge the battery. • After each use or once a
month, the minimum recharge time is 8 to 12 hours,
• The POWER SWITCH must be in the OFF position during the
Less than 20 hours max.
The battery will eventually lose the ability to hold a charge. Depending on the amount of
use and changing conditions, the battery should work for one to three years. Important!
Please recycle the discharged battery responsibly. The battery contains lead acid
(electrolyte) and must be
disposed of properly and legally. In most areas it is illegal to incinerate lead-acid batteries
or dispose of them in landfills. Take it to a federally or state approved lead-acid battery
recycler, such as a local auto battery retailer. Do not dispose of the battery with the
normal household waste!
charge.
2. Plug the charger into a wall outlet. The battery will begin to charge.
1. Plug the charger port into the input jack (the jack under the seat).

Please read this manual and the troubleshooting guide table completely before calling.
If you still need help solving the problem, contact your dealer.
Replace the battery, contact your dealer please.
Replace the battery, contact your dealer please.
Replace the battery, contact your dealer please.
Problem
The battery connector or
adapter connector is loose
The electrical system is damaged
Loud grinding or clicking
noises from the motor or
gearbox
Possible cause Solution
Check that the battery connectors are well connected
to each other. If there are loose wires around the motor,
contact your dealer.
A deadlock means that electrical power is not being
supplied to the terminal connection and the
vehicle needs repair. Contact your dealer please.
Check that the battery connectors are well
connected to each other.
Check that the battery charger is plugged into a working
electrical outlet.
Contact your dealer please.
Reset the fuse, see <Fuse>
Avoid using the vehicle in adverse conditions, see
<Safety>.
Contact your dealer please.
Contact your dealer please.
Contact your dealer please.
Recharge the battery.
Check that the battery connectors are well connected.
If there are loose wires around the motor. contact your
dealer please.
Check that the battery connectors are firmly
connected to each other when recharging
Bring the vehicle to a complete stop and shift,
see <Using Your Vehicle>
Reduce vehicle weight.
Troubleshooting Guide 14
Recharge the battery, contact your dealer please.
The battery connector or cables
are loose
The vehicle does
not work for a long time
low battery
low battery
The vehicle runs slowly
The vehicle needs a push
to
"Deadlock" in the engine
The battery is dead
Difficulty switching from
forward to reverse or vice
versa
Thermal fuse tripped
recharge
The vehicle is overloaded
advance
The battery does not recharge
Attempting to shift while the vehicle
is moving
The battery is low
Poor contact of cables or
connectors
The charger gets
hot when
the battery is old
The motor or gears are damaged
The vehicle is being used in difficult
conditions.
the battery is old
The vehicle does not work
Charger not plugged in
The charger does not work
This is normal and not a cause for
concern.
The engine is damaged

• Do not overload the vehicle.
• Do not tow anything behind the vehicle.
• Do not go up steep slopes. • Do not
drive towards fixed objects, which can cause the wheels to skid and the engine to overheat.
The battery features a thermal fuse with a break fuse that will automatically trip and cut
all power to the vehicle if the engine, electrical system, or battery is overloaded. The fuse will
reset and power will be restored after the unit is turned off for 20 seconds and then back
on. If the thermal fuse trips repeatedly during normal use, the vehicle may need repair.
Contact your dealer please.
• Do not drive in very hot weather, components may overheat. • Do not allow water or
other liquids to come into contact with the battery or other electrical components. •
Do not tamper with the
electrical system. Doing so can create a short circuit and cause the fuse to blow.
To avoid losing power, follow these guidelines:
Maintenance 15
Fusible
Our products conform to ASTM
F963; GB6675; EN71 standard and EN62115 standard.
• It is the parent's responsibility to check the main parts of the toy before using
it. They must periodically examine it for possible dangers, such as the
battery, the charger, the cable or cord, the plug, the screws that hold the casing
to other parts and that in case of damage, the toy should not be used until
said damage has been solved correctly. • Park the vehicle indoors or cover
it with a tarp to protect it from wet weather. • Recharge the battery after each
use. Only an
adult can handle the battery. Recharge the battery at least once a month
when the assault vehicle is not in use. • Do not hose down the vehicle.
Do not wash the vehicle with
soap and water. Do not drive the vehicle in rainy or snowy weather. Water will
damage the engine, electrical system, and battery. • Clean the vehicle with a
soft, dry cloth. To restore
shine to plastic parts, use a non-wax furniture polish. Do not use car wax. Do
not use abrasive cleaners. • When not in use, all electrical sources must be
turned off.
Turn off the ignition switch and disconnect the battery connection.