REVELL 1970 Chevelle SS 454 User manual

READ BEFORE YOU BEGIN
• CLEAR A SPACE TO WORK ON
• STUDY THE ASSEMBLY DRAWINGS
BEFORE YOU BEGIN
• EACH PLASTIC PART IS IDENTIFIED BY A
PART NUMBER
• DO NOT OVER TIGHTEN SCREWS
• SEE NOTE ABOUT APPLYING STICKERS
IN STEP #16
CAUTION:
POSITION ALL PARTS IN THIS KIT
CAREFULLY. PARTS WILL ONLY SNAP
TOGETHER ONCE.
Á LIRE AVANT DE COMMENCER
• DÉGAGGEZ UN ESPACE POUR TRA-
VAILLER.
• ÉTUDIEZ LES ÉTAPES DE MONTAGE
AVANT DE COMMENCER.
• CHAQUE PIÉCE EN PLASTIQUE PORTE
UN NUMÉRO DE PIÉCE.
• NE SERREZ PAS TROP LES VIS.
• LISEZ LA RE MARQUE CONCERNANT
L´APPLICATION DES AUTO COLLANTS,
´A L´ÉTAPE 16.
MISE EN GARDE:
POSITIONNEZ AVEC PRÉCAUTION TOUTES
LES PIÉCES DE CE MODÉLE RÉDUIT, CAR
VOUS NE POUVEZLES EMBOîTER QU’UNE
SEULE FOIS.
'70 Chevelle™SS 454
The 1970 Chevrolet
®
Chevelle™ SS™ 454 is one of the
most awesome muscle cars that ever prowled the streets.
The biggest, most powerful engine available was the
LS-6 454, which Chevrolet rated at a staggering 450 HP-
the highest horsepower rating of any muscle car. This
engine was capable of pushing the Chevelle to impres-
sive quarter mile times in the mid 13 second range at
around 110 mph. Some Chevelle SS 454s were equipped
with a special “cowl induction” hood with a vacuum oper-
ated flap at the rear of the hood that flipped up to draw
cool air in to the monster engine. Today, because of its
rarity and outrageous looks and performance, the 1970
Chevelle SS 454 is a highly valued collector car.
Your Revell kit features easy snap and screw together
assembly, chrome plated parts, a factory stock or low-
ered ride height option, and colorful stick-on graphics.
If you have any questions or comments, call our hotline at: [phone]
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A,
Elk Grove Village, Illinois 60007
Be sure to include the plan number (85193210200), part number, description,
your return address and phone number.
Visit our website: www.revell.com
* APPLY STICKERS
*APPLIQUEZ LES AUTO-COLLANTS
* OPTIONAL PARTS
* PIECES EN OPTION
KIT 1932 85193210200
Step 16
ANY UNUSED PARTS MAY BE DISCARDED
Sticker Placement Guide Parts Included
NOTE:
When applying stickers, avoid touching the “sticky” side to prevent finger prints on stickers. Bend sticker sheet slightly to lift edge of sticker & use a fingernail to lift
sticker from sheet. Line up sticker on body and press an edge into place, slowly working sticker with a fingernail until sticker is fully on model.
REMARQUE :
Pendant l’application des autocollants, éviter de toucher à la face collante pour ne pas laisser d’empreintes. Plier légèrement la feuille d’autocollants pour relever le
bord d’un autocollant, et le détacher de la feuille avec le bout d’un ongle. Aligner l’autocollant sur la carrosserie, appuyer pour coller un de ses bords, et continuer de
l’appliquer lentement du bout de l’ongle jusqu’à ce qu’il soit complètement collé sur le modèle réduit.
Step 13
5
9
8
3
6
7
2
10
10
4
Step 15
TIRE
★A
CUSTOM WHEEL
CHROME
YOU MAY BUILD YOUR ‘70 CHEV-
ELLE WITH A STOCK OR LOW-
ERED RIDE HEIGHT. INSERT
THE METAL AXLES THROUGH
THE LOWER HOLES FOR A
STOCK RIDE HEIGHT OR
THROUGH THE UPPER HOLES
FOR A LOWERED RIDE HEIGHT
METAL AXLE
METAL AXLE
SCREWS
10
CHASSIS
17
14
11
13
A
A
A
A
12
18
19
20
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
LOWERED
STOCK
1
TIRES
SCREWS
AXLES
8
STICKER #7 MAY BE CUT FROM
STICKER SHEET WITH BACKING
AND ATTACHED TO FRONT BUM-
PER USING WHITE GLUE
OPTIONAL
2
4
5
61
OPTIONAL DECALS
3
Revell Inc Elk Grove Village, IL. Copyright © 2009. All rights reserved.
Step 14

Step 1 Step 4
Step 7
85193210200
5
PASSENGER
SEAT FRONT
Step 10 Step 11 Step 12
Step 8
Step 9
Step 2 Step 3
Step 5
4
DRIVER SEAT
FRONT
6
DRIVER SEAT
BACK
6
PASSENGER
SEAT BACK
3
INTERIOR
TUB
8
RIGHT SIDE
INTERIOR PANEL
7
LEFT SIDE
INTERIOR
PANEL
9
DASHBOARD
10
STEERING
WHEEL
★14
SHIFTER
CHROME
17
WINDSHIELD
CLEAR
1
BODY
★12
HEADLIGHT
REFLECTOR
CHROME
18
HEADLIGHT
LENSES
CLEAR
NOTE: HEADLIGHT BEZELS
MUST BE INSERTED FROM
THE INSIDE OF BODY AND
CENTER PORTION OF
HEADLIGHT REFLECTOR
MUST BE IN FRONT OF
CHASSIS MOUNTING POST.
SEE ILLUSTRATION
★11
GRILLE / BUM-
PER
CHROME
19
TAILLIGHT
TRANSPARENT RED
20
TAILLIGHT
TRANSPARENT
RED
★13
REAR BUMPER
CHROME
2
REAR PANEL
Step 6
OUTER TAB
OUTER TAB
NOTE: INSERT
OUTER TABS OF
SEAT ASSEMBLIES
INTO PLACE FIRST,
THEN SNAP INNER
TABS INTO PLACE
AT CENTER OF
INTERIOR TUB
NOTE: ALIGN D-SHAPED HEADLIGHT PINS WITH D-SHAPED HOLES ON
HEADLIGHT REFLECTOR BEFORE PUSHING HEADLIGHTS INTO PLACE
REMOVE NUMBERED TAB
DRIVER SEAT
ASSEMBLY
PASSENGER SEAT
ASSEMBLY