AstroStart AF-RFK5225 User manual

PATENT NOS
CAN 1.130.426
USA 4.345.554 - 5.614.883
- 5.617.819 - 5.673.017
AND OTHER PATENTS PENDING
All rights reserved ® Directed Electronics Canada Inc. 2011 March 2011
2-WAY REMOTE CONTROL
RF KIT
USER MANUAL
MODEL AF-RFK5225
2-WAY E-XRT 5-button remote
with LCD display
(FRANÇAIS AU VERSO)

2
GOVERNMENT REGULATIONS
This device complies with the Industry Canada Radio Standards Specification RSS 210. Its use is authorized
only on a no-interference, no-protection basis; in other words, this device must not be used if it is determined
that it causes harmful interference to services authorized by IC. In addition, the user of this device must accept
any radio interference that may be received, even if this interference could affect the operation of the device.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates uses and can radiate radio-frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television, which can be determined by turning the
equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipmentand receiver.
Connect the equipment to an outlet on a circuit different from the one the receiver is
connected to.
Consult the dealer or an experienced radio / TV technician for help.
Warning:
Changes or modifications not expressly approved by Directed Electronics Canada Inc. could void the
user's authority to operate the equipment.
Directed Electronics Canada Inc.
2750, Alphonse-Gariepy ave.
Lachine, QC, H8T 3M2,
Canada
WWW.ASTROSTART.COM

3
THANK YOU FOR CHOOSING ASTROSTART’S RF REMOTE KIT!
We take this opportunity to remind you to properly defrost your windows and remove all the snow
on your vehicle before driving on public roads.
Rolling igloos are extremely dangerous!
We wish you an excellent journey!
USER GUIDE FOR AF-RFK5225REMOTE SYSTEM.
Models AF-RFK5225 & AF-RFK623 are remote controls that offer basic start functions
including all the features required to achieve safe remote starting. They also offer central
locking features that allow you to control the door locks as well as releasing the trunk.
Some functionalities and behaviours may not be available on certain vehicles.
Table of Contents
GOVERNMENTREGULATIONS__________________________________________________2
SAFETYPRECAUTIONS________________________________________________________4
PREPARINGTHESYSTEMFORREMOTESTARTINGFUNCTION(FORREMOTE‐STARTCAPABLE
SYSTEMSONLY)______________________________________________________________4
THE2‐WAY5‐BUTTONREMOTECONTROLWITHLCDDISPLAY________________________5
THEBATTERY_______________________________________________________________6
5225–CONFIRMATIONSEMITTEDBYTHEREMOTE________________________________8
LOCK/UNLOCKCOMMANDSANDALARMSYSTEMARMING/DISARMING________________________9
STARTCOMMANDS(FORREMOTE‐STARTCAPABLESYSTEMSONLY)__________________10
STARTINGTHEENGINE________________________________________________________10
ADVANCEDFEATURES________________________________________________________11
UTILITYCOMMANDS_________________________________________________________11
SETTINGTHEREMOTECONTROL_________________________________________________12
TABLEOFCOMMANDS________________________________________________________14
SAFETYCHECKS_____________________________________________________________15
HOODSWITCH_____________________________________________________________15
GEARSHIFTCHECKAPPLICABLETOAUTOMATICTRANSMISSIONVEHICLES_____________________15
GLOSSARY_________________________________________________________________15
WARRANTY________________________________________________________________16

4
SAFETY PRECAUTIONS
Before using this product, please carefully read the following safety precautions.
GENERAL RULES
•Never perform a remote start when a person or animal is inside the vehicle.
•Do not allow any person or animal to remain inside the vehicle when the engine is
running remotely (continuous mode).
•Immediately report any malfunction to the AstroStart dealer that performed the
installation.
•Under no circumstance can this product or its use be modified.
•Keep remote controls away from children.
•Have the engine tuned regularly to ensure optimal performance of your remote system.
•Make sure that the windshield wipers and the headlights are turned off before leaving
vehicle.
•Regularly check safety features that stop engine (see SAFETY CHECKS on page 14).
•Make sure you comply with all local regulations, which may prohibit leaving your
engine running when the vehicle is unattended in a public place.
•Always advise service personnel that your vehicle is equipped with a remote system.
•We strongly recommend that you have your remote system checked annually.
Contact a dealer in your area.
•All users of the vehicle should be aware of the safety precautions and operation
procedures.
•Make sure that the warning sticker is present on the driver's window.
PREPARING THE SYSTEM FOR REMOTE STARTING FUNCTION (FOR
REMOTE-START CAPABLE SYSTEMS ONLY)
When you exit the vehicle, you need to prepare the remote starter for its next use.
•Make sure that the automatic-transmission lever is in the "P" (Park) position.
•Set heating/air conditioning controls to desired position (when the remote starter starts
your engine, it will also turn on your climate control system).
•Turn your windshield wipers to the OFF position to avoid strain on the mechanism
should a start command be sent to the vehicle when, for example, snow prevents the
wipers from moving.
•Make sure that the headlights are turned OFF.
•Be sure not to leave your keys inside the vehicle. Certain rearming functions can
cause the doors to lock automatically.

5
THE 2-WAY 5-BUTTON REMOTE CONTROL WITH LCD DISPLAY
This remote control can control three separate vehicles. A maximum of four remote controls
can be assigned to a vehicle. See your dealer for additional remote controls.
5225 Front view
Antenna
LCD screen Side buttons
Lock button Unlock button
5225 Side view
Mini-USB
Charging Port
Programming Remote Start
Status / Trunk
USING YOUR REMOTE CONTROL
To send a command, press for 1 second on the appropriate button. The remote control
beeps when a button is pressed (if this option is on). A command may not be sent if the
button is not pressed long enough.
¾Advanced: Your remote control can command three separate vehicles (additional
systems required). To select a different vehicle, hold the “P” button ( ), located on
the side of the remote, for 1.5 seconds.
The range of your remote control can be affected by a weak battery, interference from
nearby metal structures, “hydro” poles, electronic devices (with magnetic fields), or crowded
parking lots. If no confirmation is received in a given location, move away from the sources
of interference and activate the "Status" command ( on the side of the remote). The
module will inform you of the status of door locks, the alarm and of the engine.
Note that the communication between the vehicle and the transmitter operates in only one
direction at a time. This is why it is recommended to wait for confirmations. Otherwise,
communications could be cancelled out.
OUT OF RANGE
If the vehicle is out of range, the remote will emit a soft chirp after three (3) seconds and will
show the “X” icon to indicate that the command has not been received.

6
THE BATTERY
Your remote is powered by an internal rechargeable battery that can only be serviced by an
authorized Directed dealer. Due to transit and storage time prior to your purchase, the
battery charge may have depleted. To ensure proper operation, check the battery level and
connect the 8602T battery charger if not fully charged.
LOW BATTERY
Once the low battery alerts begin (the text field flashes low bat and the remote beeps), they
will continue to command the system for a few days but should be charged at the earliest
opportunity.
CHARGING THE REMOTE CONTROL
•Plug the AC adapter into a 110V AC outlet. Insert the mini-USB connector into the
mini-USB port located on the side of the remote control (see previous page). The text
field will display “CHARGE” to indicate that the remote control is charging (The remote
remains operational while charging. It can command the system).
•Once fully charged, the text field will display “FULL”.
•The remote control is then ready for use. Disconnect the mini-USB end from the
remote control first and then the AC adapter from the AC outlet.
Note If the battery is excessively depleted when the charger is connected,
functionality may be delayed while it charges to the minimum voltage required to
operate the display, after which normal charging resumes.
Warning!
NEVER connect the supplied AC adapter to products other than the remote
control. It is a high current device designed specifically for rapid charging and
may cause severe damage or explosion when connected to any other products.
Charging the battery when the temperature is below 0°C (32°F) or above 45°C
(113°F) may cause severe battery damage and/or reduce battery life. Avoid
placing the remote control in areas exposed to extreme cold or heat (direct
sunlight) when charging the battery.
BATTERY LIFE
The remote control has many features that make it one of the most unique remote controls
on the market today, including superior long range communication. The default feature
settings provide for excellent battery charge duration. However, to maximize this duration
between charges, the following suggestions will help:
•Turning Paging OFF. The remote will not wake up to check for messages with Paging
OFF in the Setup Remote menu.
Caution! The remote will not receive alert messages from the system.
•Turn Beeping off. The button beeps are off by default, but they can be turned on in the
remote setup menu if desired. However, the melodies are unaffected by the beeps
settings and will still play normally.

7
BATTERY DISPOSAL
Directed Electronics cares about the environment. If you need to
dispose of the battery, please do so in accordance with your municipal
requirements for battery disposal or send it back to us at:
Directed Electronics Canada Inc.
2750, Alphonse-Gariepy ave.
Lachine, QC, H8T 3M2,
Canada
(Shipping and/or handling costs are the sole responsibility of the
owner/sender and will not be covered by Directed Electronics).

8
5225 – CONFIRMATIONS EMITTED BY THE REMOTE
AN AUDIBLE AND A VISUAL CONFIRMATION ARE EMITTED EACH TIME A COMMAND IS TRANSMITTED.
The LCD displays the vehicle status at all time. It is refreshed on every transmission or
when the status of the vehicle changes, unless the “Status confirmation” function is
disabled. The display shows the last confirmation received.
The following diagram shows the usefulness of each icon of the display.
1. Locked
8. Engine running (Small icon)
2. Unlocked
9. Car 1
3. Engine starting (Large icon)
10. Car 2
4. Battery Status 11. Car 3
5. Transmitting
12. Utility outputs status
6. Receiving 13. Clock Text Field
7. Out of Range / No answer
The following diagram shows each icon of the display pertaining to the security system.
1. Alert
2. Car Door (Trigger)
3. Hood (Trigger)
4. Trunk (Trigger)
5. Messages
Note: Not all the messages in the text field refer to the security
system’s functions. Text Field

9
Two types of confirmations are displayed on the remote:
Command confirmation: These confirmations are command acknowledgements. The icon
corresponding to the command is displayed to confirm the reception of the command.
Status confirmations: These confirmations are displayed when the status of a monitored zone
changes: door opening, alarm state, etc.
Command confirmations are returned immediately following a command transmission, whereas the
status confirmations may be returned up to 12 seconds after the event happened.
Out of range: In the event that the environment prevents confirmations from being received by the
remote control, the “X” icon appears.
Note: You can refresh the LCD screen display by pressing on any button or press the status button
().
CONFIRMATIONS EMITTED BY VEHICLE
Confirmations emitted by the vehicle are sent as soon as the command is received by the vehicle.
Refer to the vehicle owner’s guide for details.
LOCK/UNLOCK COMMANDS AND ALARM SYSTEM ARMING/DISARMING
If your vehicle is equipped with electric door locks, several functions can be operated by remote
control.
These features are optional and may or may not be available. Consult your dealer for
advice.
The Lock/Unlock functions also control Arming and disarming on the security system. The
arming/disarming functions only apply to compatible vehicle models equipped with an OEM
security system.
The following systems can be controlled:
•Door locks
•Trunk or hatchback release
•Interior lights
LOCK / ARM
Press the button: the doors are locked and the alarm system is armed. The parking lights flash
to confirm that the command has been received.
UNLOCK / DISARM
Press the button. The doors are unlocked and the alarm is disarmed. The parking lights flash to
confirm that the command has been received.
If OEM-available, the “Unlock“ function can be programmed in such a way that the first Unlock
command only unlocks the driver's door, while a following Unlock command unlocks the other
doors.
TRUNK RELEASE
When OEM available, press the button and hold it for 4 seconds. The trunk is released and
the parking lights flash to confirm that the command has been executed. The remote shows the
trunk opening.

10
If you are not sure you have received confirmation, repeat the command. The system will repeat
the confirmation as often as you wish.
PANIC
Panic mode is used to attract attention in a situation of emergency.
Press and hold or for at least 4 seconds to trigger the panic mode of your vehicle. Refer to
your vehicle’s owner’s manual for your available options.
Panic mode can be cancelled by pressing .
START COMMANDS (FOR REMOTE-START CAPABLE SYSTEMS ONLY)
STARTING THE ENGINE
To start the engine, press the button.
The system automatically adjusts the ignition duration for your type of vehicle (gas or diesel); the
parking lights flash then stay on when the engine is running.
Note: In a case where your RF Kit is used to operate a GM OEM remote starter, refer to the
vehicle’s owner’s manual for details of operation.
When the start command is transmitted, the system
immediately sends out one of two possible confirmations:
1. the vehicle can start.
2. the vehicle will not start.
System starting
Large Remote
Start icon
appears on
remote
The vehicle won't start if, for example, the hood is open. In
this case, the parking lights flash and the text field shows
“remote start failed”.
System not starting
Error code, text
field
The text field
displays an error
code
If the vehicle starts, the system will automatically send
another confirmation, with a melody, after a few seconds.
Successful start
Small Remote
Start icon and a
melody is played
UPON ENTERING YOUR VEHICLE...
DO NOT TURN IGNITION KEY TO START POSITION.
Automatic transmission vehicles
To avoid turning the engine off when taking place behind the steering wheel, do not apply the
brakes until you have placed the key in the ignition and turned it to the RUN position.
Drive as usual.