ASUNA 7130 User manual

7130
Lancer Rear Drive Magnetic
Commercial Indoor Cycling Bike
Owner’s Manual
Made in Taiwan

INDEX
IMPORTANT SAFETY INFORMATION ..................................................................... 1
EXPLODED DRAWING ............................................................................................. 2
PARTS LIST................................................................................................................ 3
ASSEMBLY INSTRUCTION.................................................................................... 4-9
USER INSTRUCTION .............................................................................................. 10
MAINTENANCE ....................................................................................................... 11
EXERCISE INSTRUCTION ................................................................................. 12-13
ATTENTION: Please verify that all parts associated with this product are in good
condition and accounted for. During the assembly process please be sure to follow
each step accordingly as it has been explained within the manual.
WARNING: During assembly it is recommended that all bolts be tightened by
hand, upon completing assembly, bolts should then be properly secured using the
wrench provided. To avoid injury, check bolts carefully before use.
WARNING: This product can expose you to one or more chemicals known to
the State of California to cause cancer and birth defects or reproductive
harm. For more information go to www.P65Warnings.ca.gov.
IMPORTANT: Read all instructions carefully before using this product. Retain
owner’s manual for future reference. For customer service, please contact:
[e-mail]

IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this
equipment correctly. It is important to read this entire manual before assembling and using
the equipment. Safe and effective use can only be achieved if the equipment is assembled,
maintained and used properly. It is your responsibility to ensure that all users of the
equipment are informed of all warnings and precautions.
1. Before starting any exercise program you should consult your physician to determine if
you have any medical or physical conditions that could put your health and safety at risk,
or prevent you from using the equipment properly. Your physician’s advice is essential if
you are taking medication that affects your heart rate, blood pressure or cholesterol
level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your
health. Stop exercising if you experience any of the following symptoms: pain, tightness
in your chest, irregular heartbeat, shortness of breath, lightheadedness, dizziness or
feelings of nausea. If you do experience any of these conditions, you should consult
your physician before continuing with your exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult
use only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or
carpet. To ensure safety, the equipment should have at least 2 feet (60cm) of free space
all around it.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The
safety of the equipment can only be maintained if it is regularly examined for damage
and/or wear and tear.
6. Always use the equipment as indicated. If you find any defective components while
assembling or checking the equipment, or if you hear any unusual noises coming from
the equipment during exercise, discontinue use of the equipment immediately and do
not use until the problem has been rectified.
7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may
become entangled in the equipment. Do not use without shoes, or with loose shoes.
8. Do not place fingers or objects into moving parts of the exercise equipment.
9. The maximum weight capacity of this unit is 285 pounds (130kgs).
10. The equipment is not suitable for therapeutic use.
11. Please take proper precautions when lifting and moving the equipment. Always use
proper lifting technique and seek assistance if necessary.
12. For all adjustable parts be aware of the maximum position to which they can be adjusted.
13. Be aware of non-fixed or moving parts while mounting or dismounting the bike.
14. We take no responsibility for personal injury or damage sustained by or through the use
of this exercise bike.

Exploded Drawing

NO.
NAME
QTY
NO.
NAME
QTY
1
Saddle
1
35
Flywheel axle
1
2
Alloy bind clamp ( L )
3
36
Fixed wheel nut
2
3
Spring for release lever
3
37
Flywheel bearing
5
4
Alloy bind clamp ( R )
3
38
Axle bolt for moving wheel
2
5
Washer for release lever
3
39
Moving wheel
2
6
Release lever- L Shape Adjustment
Knob
3
40
Plastic washer for release lever
3
7
Crank bolt
2
41
Fixed bolt for release lever
3
8
Nut
4
42
Seat slider w/ end cap, plug
1
9
Washer
4
43
Seat post
1
10
Bolt
4
44
Stainless washer for release lever
3
11
Pedal
1PR
45
Belt
1
12
Front / Rear foot tube end cap
4
46
Spring
1
13
Foot tube adjuster pad
4
47
Outer belt guard bolt M5
12
14
Rear stabilizer
1
48
Bottle holder clamp
1
15
Flywheel security nut (7t)
2
49
Flywheel (complete)
1
16
Flywheel adjuster bolt
2
50
Rubber sleeves
3
17
L shape adjustment knob
1
51
Bolt for tension adjuster casing
2
18
Front stabilizer
1
52
Idler w/bearing, clip
1
19
Right belt guard
1
53
Rubber sealed
1
20
Left crank arm
1
54
Handle for tension adjuster
1
21
Right crank arm
1
55F
Front casing for tension adjuster
1
22
Handle bar post
1
55R
Rear casing for tension adjuster
1
23
Handle bar
1
56
Bolt for tension adjuster handle
2
24
Tension adjuster (complete)
1
57
Adjuster cable guide
1
25
Bolt for bottle holder
2
58
Rubber cover for flywheel
2
26
Bottle holder
1
59
Washer for plate
2
27
Fixed bolt for plate
2
60
Flywheel protection tube
1
28
End cap
3
61
Bolt for protection tube
3
29
End plug
1
62
Washer for protection tube
6
30
Belt pulley
1
63
C rubber sealed
1
31
Left belt guard
1
64
Washer for L shape adjustment knob
2
32
Nut for bottle holder
2
65
O clip for L shape adjustment knob
1
33
BB bearing
3
66
Screw for pulley
5
34
BB Axle with plate
1
G01
Magnetic holder w/magnetic set
1
Parts list

STEP 1:
Attach the Front Stabilizer (18) and the Rear Stabilizer (14) to the Main Frame (Y)
using 4 Bolts (10), 4 Washers (9) and 4 Nuts (8). Tighten and secure using spanner
wrench.
Assembly Instruction
(Y)

STEP 2:
Remove plug from head tube of Main Frame (Y). You may have to loosen handle
to remove it.
Insert the Handlebar Post (22) into the head tube of the Main Frame (Y). Move
Handlebar Post (22) to the desired height. Tighten the Release Lever (6) to
secure the Handlebar Post (22) into position.
Slide the Handlebar (23) onto the Handlebar Post (22). Tighten the L Shape
Adjustment Knob (17) to secure the Handlebar (23) into position.
NOTE: To slide the Handlebar (23) back and forth to adjust it to the desired
position, first loosen the L Shape Adjustment Knob (17).
Assembly Instruction
(Y)

STEP 3:
Insert the Seat Post (43) into the seat tube located on the Main Frame (Y).
Insert the Seat Slider (42) into the Seat Post (43). Tighten the Release Lever
(6) to secure the Seat Slider (42) in place.
Secure the Saddle (1) onto the post of the Seat Slider (42). Tighten the saddle
clamp screw to secure the Saddle (1) in place.
Use Release Lever (6) to adjust height of the saddle, use Release Lever (6) to
adjust the saddle back and forth.
Assembly Instruction

STEP 4:
Connect Pedals L/R (11) onto the Left and Right Crank Arms (20 and 21).
(Before you begin, immobilize the crank arms by turning the tension control
adjuster all the way to the right).
NOTE: Pedals L/R (11) are marked, Lfor the (left pedal) and Rfor the (right
pedal).
Left Pedal: align the left pedal, Pedal L (11) with the Left Crank Arm (20) at 90
degrees. Gently insert the pedal into the crank arm, turn the pedal
counter-clockwise as tightly as you can with your hand. Tighten and secure
with (15mm) spanner wrench.
Right Pedal: align the right pedal, Pedal R (11) with the Right Crank Arm (21)
at 90 degrees. Gently insert the pedal into the crank arm, turn the pedal
clockwise as tightly as you can with your hand. Tighten and secure with (15mm)
spanner wrench.
There is a Bottle Holder (26) (when you received it already assembled with
Bottle Holder Clamp (48), Nut For Bottle Holder (32) and Bolt For Bottle
Holder (25))you can mount it on top of Handlebar (23). Then tighten
clamp screws.
Assembly Instruction
IMPORTANT:
Read instructions
carefully, failure to
do so may cause
permanent damage
to your bike.
23

STEP 5:
Adjust the exercise resistance on the bike using the Tension Adjuster (24) to
increase (-) or decrease (+) resistance.
Emergency Brake –This bike can be instantaneously stopped by
rotating the red Tension Adjuster (24) completely forward.
Assembly Instruction
24

Assembly is complete!

Before beginning use of equipment, please be sure to inspect the entire bike
carefully. Ensure that all moving and stationary parts have been properly
installed and are operational. Inspect all screws, nuts and bolts as well to
make sure that they are tightened and secure.
MOVING
There are Moving Wheels (39) on the rear stabilizer. Hold the front stabilizer,
and lift the bike until the wheels touch the ground. Then you can move the bike.
39

This bike is designed to be used in fitness and health clubs.
ASSEMBLY
Properly assembling the equipment before use is very important. Be sure to
follow all instructions as detailed in the assembly instructions section of the
owner’s manual.
ADJUSTING THE RESISTANCE
Adjust the resistance of the bike using the Tension Adjuster. Increase the
level of resistance by moving it forward, and decrease the level of resistance
by moving it back.
HANDLEBAR AND SEAT ADJUSTMENT
It is important that the handlebar and seat are both set to the correct height of
your body. To adjust the handlebar height, loosen the Handlebar Release
lever and slide the Handlebar Post up or down to the required height. Once
adjusted, retighten the handlebar release lever. Ensure that it is securely
tightened and that isn’t any lateral or vertical movement of the handlebar. The
Handlebar can also be adjusted forwards or backwards. To do so loosen the L
Shape Adjustment Knob located below the handlebar slider. Slide the
handlebar assembly forwards and backwards until you reach the required
position. Once adjusted, tighten the L shape adjustment adjuster.
SADDLE ADJUSTMENT
To adjust the saddle height, loosen the Release Lever, move the saddle up or
down to the required height. Once adjusted, retighten the release lever.
Ensure that the release lever is tight enough to prevent the saddle from
moving side to side. The Saddle can also be adjusted forwards or backwards.
To do so, loosen the Release Lever (6) located at the top of the Seat Post.
Slide the Seat Slider to the required position. Once adjusted, retighten the
seat slider release lever.
PEDALS AND TOE STRAPS
Feet should be securely positioned in the toe clips during exercise. Put your
foot as far forwards as you can into the toe-clip and then pull the strap tight.
Repeat this process to secure your other foot.
ADJUSTING THE HEIGHT OF THE BIKE
Located underneath the Front and Rear Stabilizers of the bike are height
adjustment pads. These pads are used to adjust the height of the bike in order
to increase the amount of stability to the ground. To increase the height of the
bike, turn the adjustment pad counter-clockwise. To decrease the height of the
bike, turn the adjustment pad clockwise.
BRAKE to stop the bike, rotating the Tension Adjuster completely forward
located at the top of the Main Frame.
User Instruction

Maintenance
IMPORTANT:
Safe and effective use can only be achieved if the equipment is assembled, maintained
and used properly. It is your responsibility to ensure that the equipment is maintained
regularly. Any components found to be worn and/or damaged should be replaced before
continuing use of the equipment. Equipment should only be used and stored indoors,
prolonged exposure to weathering and changes in temperature and humidity may have a
severe impact on moving parts of the machine.
Daily Maintenance:
-Clean away sweat and moisture after each use.
-Perform inspection of all nuts and bolts associated with moving parts of the equipment
and tighten as required.
-Check the mobility of moving parts and components on the equipment, lubricate if
required. -Clean plastic parts of the equipment using a damp cloth, clean metal parts of
the equipment using a dry cloth. Do not use cleaning products to clean the equipment.
Weekly Maintenance:
-Thoroughly inspect the equipment; nuts, bolts, screws and moving parts such as foot
pedals, saddle, pulleys, etc. Tighten or replace parts as required.
Monthly Maintenance:
-Inspect the frame and inner working components for wear and tear as well as damage.
Perform maintenance or replace parts as required.
Version 1.2