Asus ET2300INTI User manual

1
User Guide for Windows® 8
Conguring the audio output via an HDMI device
If you want to use a high-denition TV as an audio output device, connect it to your Home
Theater PC and follow the steps below to congure the audio settings.
1. From the Metro Start Screen, click Desktop to launch the Desktop Mode.
2. Right-click the Volume Mixer icon on the Windows®
taskbar and click Playback devices.
3. From the Playback screen, select Digital Audio
(HDMI).
4. Click Congure and the Speaker Setup window
pops up.
NOTE: For updates on these system requirements, visit http://www.windows.microsoft.com/en-
us/windows-8/faq
Processor 1GHz or faster
RAM 1GB (32-bit) or 2 GB (64-bit)
Hard disk space 16 GB (32-bit) or 20 GB (64-bit)
Graphics card Microsoft DirectX9 graphics device with WDDM driver
Screen resolution 1024 x 768 for Metro Style Apps
1366 x 768 for Snap feature
System requirements
To facilitate a smoother transition from your previous operating system, read the system
requirements below before upgrading to Windows® 8:
E7671 / First Edition / August 2012

2
5. Select Stereo and click Next.
6. Tick the Front left and right option, and
click Next.
7. Click Finish to exit the speaker setup.
Turning your All-in-one PC off
Do any of the following to shut down your All-in-one PC:
• Tap from the Charm bar then tap > Shut down to do a normal shutdown.
• From the log-in screen, tap > Shut down.
• If your All-in-one PC is unresponsive, press and hold the power button for at least four
(4) seconds until your All-in-one PC turns o.

3
Entering the BIOS Setup
Windows
®
8 boot time is quite fast, so we developed three ways for you to quickly access
the BIOS (Basic Input and Output System), which stores system hardware settings that are
needed for system startup in your All-in-one PC.
To quickly access the BIOS, do any of the following:
When your All-in-one PC is o, press the power button for at least four (4) seconds to
access the BIOS directly.
Press the power button for at least four (4) seconds to shut down your All-in-one PC,
then press the power button again to turn your All-in-one PC back on, and press <F2>
during POST.
When your All-in-one PC is o, disconnect the power cord from your All-in-one PC’s
power connector. Reconnect the power cord and press the power button to turn on your
All-in-one PC. Press <F2> during POST.
NOTE: POST (Power-On Self Test) is a series of software controlled diagnostic tests that run when
you turn on your All-in-one PC.
WARNING! Inappropriate BIOS settings may result to instability or boot failure. We strongly
recommend that you change the BIOS settings only with the help of a trained service personnel.
•
•
•

4
Connecting to the Internet
Access emails, surf the Internet, and share applications via social networking sites on or from
your All-in-one PC using wireless/Wi-Fi or wired connection.
Wi-Fi connection
To set up your Wi-Fi connection:
1. Do the following steps to activate Wi-Fi in your All-in-one PC:
a) Launch the Charm bar.
b) Tap and tap .
c) Select an access point from the list of available Wi-Fi connections.
2. Tap Connect to start the network connection.
NOTE: You may be prompted to enter a security key to activate the Wi-Fi connection.
3. If you want to enable sharing between your All-in-one PC and other wireless-enabled
systems, tap Yes, turn on sharing and connect to devices. Tap No, don't turn on
sharing or connect to devices if you do not want to enable the sharing function.
Wired connection
To set up your wired connection:
1. Use a network (RJ-45) cable to connect your All-in-one PC to a DSL/cable modem or a
local area network (LAN).
2. Turn on your computer.
3. Congure the necessary Internet connection settings.
NOTES:
• For more details, refer to the sections Conguring a dynamic IP/PPPoE network connection or
Conguring a static IP network connection.
• Contact your Internet Service Provider (ISP) for details or assistance in setting up your Internet
connection.

5
Conguring a dynamic IP/PPPoE network connection
To congure a dynamic IP/PPPoE or static IP network connection:
1. From the Metro Metro Start Screen, click Desktop to launch the Desktop mode.
2. From the Windows
®
taskbar, right-click the network icon and click Open Network
and Sharing Center.
3. From the Open Network and Sharing Center screen, click Change Adapter settings.
4. Right-click on your LAN and select Properties.
5. Click Internet Protocol Version 4(TCP/IPv4) and click Properties.
6. Click Obtain an IP address automatically and click OK.
NOTE: Continue to the next steps if you are using PPPoE connection.
7. Return to the Network and Sharing Center and then click Set up a new connection
or network.
8. Select Connect to the Internet and click Next.
9. Select Broadband (PPPoE) and click Next.
10. Enter your User name, Password, and Connection name. Click Connect.
11. Click Close to nish the conguration.
12. Click the network icon in the taskbar and click the connection you just created.
13. Enter your user name and password. Click Connect to connect to the Internet.
Conguring a static IP network connection
To congure a static IP network connection:
1. Repeat steps 1 to 4 of the previous section Conguring a dynamic IP/PPPoE network
connection.
2 Click Use the following IP address.
3. Enter the IP address, Subnet mask and Gateway from your service provider.
4. If needed, enter the preferred DNS Server address and alternative address.
5. When done, click OK.

6
Recovering your system
Resetting your All-in-one PC
The Reset your PC option restores your PC to its factory default settings.
IMPORTANT! Back up all your data before using this option.
To reset your All-in-one PC:
1. Press <F9> during bootup.
2. From the screen, click Troubleshoot.
3. Select Reset your PC.
4. Click Next.
5. Select Only the drive where the Windows is installed.
6. Select Just remove my les.
7. Click Reset.
Recovering from a system image le
You can create a USB recovery drive and use this to recover your All-in-one PC’s settings.
Creating a USB recovery drive
WARNING! All les on your USB storage device will be permanently deleted during the process.
Before you proceed, ensure that you back up all your important data.
To create a USB recovery drive:
1. Launch the Control Panel from the All Apps screen.
2. From the Control Panel’s System and Security, click Find and x problems.
3. Click Recovery > Create a recovery drive.
4. Click Next.

7
5. Select the USB storage device where you
want to copy the recovery les.
6. Click Next.
7. Click Create. Wait for a while for the process
to complete.
8. When the process is completed, click Finish.
Removing everything and reinstalling Windows
Restoring your All-in-one PC to its original factory settings can be done using the Remove
everything and reinstall option in PC Settings. Refer to the steps below to use this option.
IMPORTANT! Back up all your data before using this option.
NOTE: This process may take a while to complete.
1. Launch the Charm bar.
2. Click Settings > Change PC Settings > General.
3. Scroll down to view the Remove everything and reinstall Windows option. Under this
option, click Get Started.
4. Follow the onscreen instructions to complete the reinstallation and reset process.

8
15060-15520000