Asus Z9200K Series User manual

Disassembly Procedure
2–1
Disassembly Procedure
Please follow the information provided in this section to perform the complete
disassembly procedure of the notebook. Be sure to use proper tools
described before.
SUS Z9200K Series Notebook consists of various modules. This chapter describes the
procedures for the complete notebook disassembly. In addition, in between procedures,
the detailed disassembly procedure of individual modules will be provided for your
service needs.
The disassembly procedure consists of the following steps:
•Battery Module
•Memory Module
•Wireless LAN Module
•HDD Module
•ODD Module
•Keyboard
•LCD Module
•Top Case Module
•Main Board Module
•Modem Module
•CPU/Heat Sink Module
Chapter
2
A

Disassembly Procedure
2 - 2
Battery Module
The illustration below shows how to remove the battery module.
1. Unlock and hold the latches, and remove the battery.
2. Slide the battery latch (No.1) to unlock and Firmly slide the other latch (No.2) to the
top and remove the battery
Memory Module
The Z9200K Series Notebook do not have onboard RAM. There are two SO-DIMM
sockets for installing SO-DIMM RAM. It can upgrade the total memory size up to 2GB
with a 512MB module on each socket.
Removing Memory module
1. Remove 4 screws and remove DIMM door.
BATTERY
SECOND
MEMORY
MODULE
MEMORY
REMOVAL
L

Disassembly Procedure
2 - 3
2. Take the memory DIMM cover away as the picture shows.
Wireless Lan Module
The illustration below show show how to remove the Wireless LAN module
Disassembling Wireless Lan board.
1. Remove 2 Antenna cables from Wireless LAN Module.
2. Take the Wireless Lan away as the picture shows.
WIRELESS
LAN
REMOVAL
WIRELESS LAN
MODULE
REMOVAL
30°

Disassembly Procedure
2 - 4
HDD Module
The illustrations below show how to remove the HDD module from the notebook.
Removing HDD Module
1. Remove 1 screw and lift the HDD cover away.
2. Pull the hard disk module toward the direction of the arrow and lift it up and take it
out.
HDD
MODULE
HDD
MODULE
REMOVAL

Disassembly Procedure
2 - 5
ODD Module
1. Remove 2 screws.
2. Remove the Mylar.
3. Push the metal plate with a screw driver and pull the ODD out.
OPTICAL
DRIVE
REMOVAL

Disassembly Procedure
2 - 6
CPU Module
The illustrations below show how to remove the CPU module from the notebook.
Removing CPU
1. Remove the rubber.
2. Remove 4 screws aside the CPU. And take away the thermal module.
3. Remove the CPU slot and take away the CPU.
CPU MODULE
REMOVAL
CPU
REMOVAL
4
1
2
3

Disassembly Procedure
2 - 7
LCD Module
The illustrations below show how to disassemble the LCD module. The module
contains LCD panel, Inverter board, LCD Hinge bracket, Hinge cover, LCD front
cover, LCD back cover
Disassembling LCD Module
1. Remove 3 screws on both side.
2. Remove both hinge covers
3. Remove 2 screws on the hames cover and take the hames cover away
LCD
MODULE
LCD
DISASSEMBLY

Disassembly Procedure
2 - 8
4. Remove 1 screw and disconnect the connector.
5. Remove 1 screw and disconnect the connector.
6. Remove 2 screws on both ends.

Disassembly Procedure
2 - 9
7. Remove the LCD module from system.
Disassembling LCD Module
1. Remove 5 rubber pads and 5 screws(M2.5 x 8L) from LCD module.
2. Prying the inside edges of the bezel, then separate it from LCD back cover and take
LCD front bezel away.
LCD
DISASSEMBLY

Disassembly Procedure
2 - 10
Disassembling inverter board
3. Remove 1tape and disconnect 2 cables.
4. Take away the inverter board.
Disassembling LCD panel
1. Remove 10 screws and take away the LCD panel.