Asus MM19D User manual

ASUSMM19D
1
19” LCD MONITOR
MM19D
THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT
HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE
ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RE LIABILITY FOR
CHANGES, ERRORS OR OMISSIONS.
SERVICE MANUAL
http://www.wjel.net

ASUSMM19D
2
Table of Content
Revision List…………………………………………………………………………………………………………. 3
1. Monitor Description…………………………………………………………………………………………….. 4
2. LCD Monitor Description……………………………………………………………………………………….. 5
3. Operating Instructions………………………………………………………………………………………….. 6
3.1 General Instructions…………………………………………………………………………………………... 6
3.2 Front Panel Control……………………………………………………………………………….…………... 6
3.3 Adjusting the Picture………………………………………………………………………………………….. 7
4. Input/Output Specification……………………………………………………………………………………... 9
4.1 Input Signal Connector……………………………………………………………………………………….. 9
4.2 Power Supply Requirements………………………………………………………………………………… 9
4.3 Factory Preset Display Modes……………………………………………………………………………….. 10
4.4 Panel Specification………………………………………………………………………………………….… 11
4.4.1 General Description………………………………………………………………………………….…... 11
4.4.1 Display Characteristics…………………………………………………………………………………... 11
4.4.2 Optical Characteristics…………………………………………………………………………………… 12
4.4.3 Electrical Characteristics………………………………………………………………………………… 13
5. Block Diagram………………………………………………………………………………………………….… 14
5.1 Monitor Exploded View………………………………………………………………………….……………. 14
5.2 Software Flowing Chart………………………………………………………………………………….…… 15
5.3 Electrical Block Diagram……………………………………………………………………………………… 17
5.3.1 Main Board………………………………………………………………………………………………... 17
5.3.2 Inverter/Power Board………………………………………………………….…………………………. 18
6. Schematic……………………………………………………………………………………………………….… 19
6.1 Main Board…………………………………………………………………………………………………….. 19
6.2 Power Board…………………………………………………………………………………………………… 25
7. PCB Layout………………………………………………………………………………………………………. 29
7.1 Main Board…………………………………………………………………………………………………….. 29
7.2 Power Board…………………………………………………………………………………………………… 30
7.3 Key Board………………………………………………………………………….…………………………... 30
8. Maintainability……………………………………………………………………………………………………. 31
8.1 Equipments and Tools Requirement………………………………………………………………………… 31
8.2 Trouble Shooting…………………………………………………………………………………………….… 32
8.2.1 Main Board………………………………………………………………………………………………... 32
8.2.2 Inverter/Power Board…………………………………………………………………………………….. 35
8.2.3 Keypad Board…………………………………………………………………………………………….. 37
9. White-Balance, Luminance adjustment………………………………………………………………….….. 38
10. EDID Content……………………………………………………………………………………………………. 40
11. BOM List………………………………………………………………………………………………………... 41
http://www.wjel.net

ASUSMM19D
3
Revision List
Version Date Revision History TPV Model Name
A00 Apr-18-06 Initial Release T980KH4DTAUSNP
http://www.wjel.net

ASUSMM19D
4
1. Monitor Specifications
Items Description
Driving system TFT Color LCD
Type HSD190ME13
Size 48.0cm(19.0")
Pixel pitch 0.294mm (H) x 0.294mm (V)
Viewable angle 160(H) 160(V)(CR>5)
LCD Panel
Response time 8 ms
Sync. Type H/V TTL
Input Signal 15Pin Analog
H-Frequency 30kHz – 80kHz
Input
V-Frequency 55-75Hz
ON Mode <55W
Power Consumption
OFF Mode <2W
Display Color 16.2M (6-bits+FRC)
Contrast Ratio 700:1
Dot Clock 135MHz
White Luminance 300cd/m2
Max. Resolution 1280 x1024
Plug & Play VESA DDC2BTM
Power Source 100~240VAC,47~63Hz
Maximum Screen Size Horizontal : 376.32mm
Vertical: 301.056mm
Environmental
Conditions
Operating Temp: 0°C to 35°C
Storage Temp: -20°C to 60°C
Operating Humidity: 45% to 85%
http://www.wjel.net

ASUSMM19D
5
2. LCD Monitor Description
The LCD MONITOR will contain a main board, a power board, a keypad board which house the flat panel control
logic, brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.
Video signal, DDC
CCFT Drive.
PWPC Board
(
Include Ada
p
ter and Inverter
)
Flat Panel and
CCFL backlight
Main Board
RS232 Connector
For white balance
adjustment in factory
mode
HOST Computer
AC-IN
100V-240V
Monitor Block Diagram
Keyboard
http://www.wjel.net

ASUSMM19D
6
3. Operating Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control buttons are located in front panel of the
monitor. By changing these settings, the picture can be adjusted to your personal preferences.
•The power cord should be connected.
•Connect the video cable from the monitor to the video card.
•Press the power button to turn on the monitor position. The power indicator will light up.
3.2 Front Panel Control
-Power Button:
When pressed, the monitor enters the off mode, and the LED turns blank. Press again to restore normal status.
-Left / Right Button:
The Left/Right Button is used to control the monitor functions. Press to switch functions or adjust settings.
- Auto Adjust Key:
The Auto Adjust Key is used to automatically set the H Position, V Position, Clock and Phase.
-Power Indicator:
Blue — Power On mode.
Amber — Power Saving mode.
Dark —Power Off Mode.
NO. Name Within OSD Without OSD
①Splendid Button Exit OSD or back to previous menu
1.Activate Scenario selection menu.
2. Automatically adjust the image to its
optimized position, clock, and phase by
pressing the button for 2 seconds.
②- / Button Decrease the level of the function select
or move to the previous function. Activate Contrast adjustment menu
③Power Button
Switch the LCD monitor on or off.
Blue: normal operation mode.
Amber: power saving mode.
Dark: power off mode
Switch the LCD monitor on or off.
Blue: normal operation mode.
Amber: power saving mode.
Dark: power off mode
④+/ Button Increase the level of the function select
or move to the next function. Activate Brightness adjustment menu.
⑤Menu Button Enter/select the icon highlighted . Activate the OSD main menu.
http://www.wjel.net

ASUSMM19D
7
3.3 Adjusting The Picture
Adjustment steps:
1. Press the MENU-button to activate the OSD window.
2. Press < or > to select the desired function.
3. Press the MENU-button to select the function that you want to adjust.
4. Press < or > to change the settings of the current function.
5. To exit and save, select the exit function, or leave the monitor alone for 10 seconds. If you want to adjust any
other function, repeat steps 2-4.
OSD TABLE:
Main Menu
Item
Main Menu
Icon Sub Menu Item Sub Menu Icon Description
Scenery Mode
Advance for scenery use with Splendid™ Video
Enhancement
Text Mode
Advance for generic Windows use (Splendid™ Off)
Theater Mode
Advance for movie use with Splendid™ Video
Enhancement
Game Mode
Advance for game use with Splendid™ Video
Enhancement
Scenario
Night Mode
Advance for dark-display use with Splendid™ Video
Enhancement
R Adjust red gain
G Adjust green gain
RGB
B Adjust blue gain
Reddish Select yeddish skin stone
Color
Skin Tone
Natural Select natural skin stone
http://www.wjel.net

ASUSMM19D
8
Yellowish Select yellowish skin stone
Cool The image appears bluer.
(9300°K)
Normal Normal image color. (7500°K)
Color
Temperature
Warm The image appears redder.
(6500°K)
Brightness
Adjust the brightness level
Luminance
Contrast
Adjust the contrast level
H-Position
Adjust the horizontal position of the OSD
V-Position
Adjust the vertical position of the OSD
OSD Setup
OSD Timeout
Adjust the OSD timeout
Phase
Adjust the image Phase to
reduce Horizontal-line noise of
the image
Focus
Clock
Adjust the image Clock to
reduce Vertical-line noise of the
image
H-Position
A
djust the horizontal position of
the image
Image Position
V-Position Adjust the vertical position of
the image
Image Setup
Auto
Auto adjust the horizontal/vertical positions, phase
and clock of the image
Information
Show the resolution, H/V frequency and input port of current input timing
Language
Select the language you like
Reset
Recall factory setting
Exit
Exit OSD
http://www.wjel.net

ASUSMM19D
9
4. Input/Output Specification
4.1 Input Signal Connector
Analog Connector
Pin No. Description Pin No. Description
1. Red 9. +5V
2. Green 10. Logic Ground
3. Blue 11. Monitor Ground
4. Monitor Ground 12. DDC-Serial Data
5. DDC-Return 13. H-Sync
6. R-Ground 14. V-Sync
7. G-Ground 15. DDC-Serial Clock
8. B-Ground
VGA connector layout
15
610
11 15
4.2 Power Supply Requirement
A/C Line voltage range : 100 V ~ 240 V
A/C Line frequency range : 50 ±3Hz, 60 ±3Hz
Input Current : 1.5A max at 100V; 0.8A max at 240 V
Peak surge current : < 60A peak at 240 VAC and cold starting
< 30A peak at 120VAC and cold starting
Leakage current : < 3.5mA
Power line surge : No advance effects (no loss of information or defect)
with a maximum of 1 half-wave missing per second
http://www.wjel.net

ASUSMM19D
10
4.3 Factory Preset Display Modes
VESA MODES
Horizontal Vertical
Mode Resolution Total
Nominal
Frequency
+/- 0.5kHz
Sync
Polarity
Nominal
Freq.
+/- 1 Hz
Sync
Polarity
Nominal
Pixel
Clock
(MHz)
640x480@60Hz 800 x 525 31.469 N 59.940 N 25.175
640x480@72Hz 832 x 520 37.861 N 72.809 N 31.500
VGA
640x480@75Hz 840 x 500 37.500 N 75.00 N 31.500
800x600@56Hz 1024 x 625 35.156 N/P 56.250 N/P 36.000
800x600@60Hz 1056 x 628 37.879 P 60.317 P 40.000
800x600@72Hz 1040 x 666 48.077 P 72.188 P 50.000
SVGA
800x600@75Hz 1056x625 46.875 P 75.000 P 49.500
1024x768@60Hz 1344x806 48.363 N 60.004 N 65.000
1024x768@70Hz 1328x806 56.476 N 70.069 N 75.000
1024x768@75Hz 1312x800 60.023 P 75.029 P 78.750
XGA
1024x768@72Hz 1304x798 57.7 P 72 P 78.4
1152x864@75Hz 1600x900 67.5 P 75 P 108
1280x1024@60Hz 1688x1066 63.981 P 60.020 P 108.000
1280x1024@75Hz 1688x1066 79.976 P 75.025 P 135.000
1280x960@60Hz 1800x1000 60 P 60 P 108
1280x1024@70Hz 74.4 P 70 P 124.9
SXGA
1280x1024@72Hz 77.9 P 72 P 134.6
IBM MODES
Horizontal Vertical
Mode Resolution Total
Nominal
Frequency
+/- 0.5kHz
Sync
Polarity
Nominal
Freq.
+/- 1 Hz
Sync
Polarity
Nominal
Pixel
Clock
(MHz)
DOS* 720x400@70Hz 900 x 449 31.469 N 70.087 P 28.322
DOS 640x350@70Hz 800 x 449 31.469 P 70.087 N 25.175
MAC MODES
VGA 640x480@67Hz 864x525 35.000 N 66.667 N 30.240
SVGA 832x624@75Hz 1152x667 49.725 N 74.551 N 57.2832
http://www.wjel.net

ASUSMM19D
11
4.4 Panel Specification
4.4.1 General Description
 19”SXGA TFT LCD Panel
 4 CCFLs Backlight System
 Supported SXGA (V:1024 lines, H:1280 pixels) Resolution
 Supported to 75Hz Refresh Rate
 LCD Timing Controller
 RoHS Compliance
 VESA Compatible
4.4.2 Display Characteristics
http://www.wjel.net

ASUSMM19D
12
4.4.3 Optical Characteristics
http://www.wjel.net

ASUSMM19D
13
4.4.4 Electrical Characteristics
1. TFT LCD Module
2. Backlight Unit
http://www.wjel.net

ASUS MM19D
14
5. Block Diagram
5.1 Monitor Exploded View
http://www.wjel.net

ASUS MM19D
15
5.2 Software Flowing Chart
1
2
N
Y
5
Y
N
10
Y
N
12
Y
N
7
Y
N
6
4
3
8
9
14
11
13
Y
N
15
Y
N
16
17
19
Y
N
18
http://www.wjel.net

ASUS MM19D
16
REMARK:
1) MCU initialize.
2) Is the EEprom blank?
3) Program the EEprom by default values.
4) Get the PWM value of brightness from EEprom.
5) Is the power key pressed?
6) Clear all global flags.
7) Are the AUTO and SELECT keys pressed?
8) Enter factory mode.
9) Save the power key status into EEprom.
Turn on the LED and set it to green color.
Scalar initialize.
10) In standby mode?
11) Update the lifetime of back light.
12) Check the analog port, are they’re any signals coming?
13) Does the scalar send out an interrupt request?
14) Wake up the scalar.
15) Are there any signals coming from analog port?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the message
disappear.
17) Program the scalar to be able to show the coming mode.
18) Process the OSD display.
19) Read the keyboard. Is the power key pressed?
http://www.wjel.net

ASUS MM19D
17
5.3 Electrical Block Diagram
5.3.1 Main Board
MCU
W79E632
(U601)
Scalar IC TSU16AWK
(Include ADC, OSD)
(U401)
EEPROM
M24C16
(U602)
D-Sub
Connector
(CN301)
EEPROM
M24C02
(U301)
H sync
V sync
RGB
DB15_SDA,
DB15
_
SCL
EPR_SDA
EPR_SCL
LCD Interface
(CN503)
Key Board
Control
Crystal
24MHz
(X601)
Crystal
14.318MHz
(X401)
http://www.wjel.net

ASUS MM19D
18
5.3.2 Inverter/Power Board
CN902
EMI filter
Bridge
Rectifier
and Filter
Start Circuit
R906, R907
PWM
Control IC
Over
Voltage
Protect
AC input
12V
PWM
Control IC
Feedback
Circuit
OSC and
Output
Circuit
DC Convert
Circuit
MOSFET
Over
Voltage
Protect
Lamp
ON/OFF
ON/OFF
Control
Rectifier
diodes
Feedback
Circuit
Transformer
DIM
IC101
5V
http://www.wjel.net

ASUS MM19D
19
6. Schematic
6.1 Main Board
715G1423-3-512
PA[0..9]
VCC3.3
B1
3.INPUT
RIN
GIN
BIN
VSYNC
GNDR
GNDG
GNDB
ST_DET1 HSYNC
SOGDDC_CLK
DDC_DAT
R+
R-
G-
G+
B+
B-
CLK+
CLK-
TXD
RXD
DDC_WP
DVI_DET
DDCCI_SEL
B3
6.MCU
onBACKLITE
onPANEL_5V/3.3V
SDA
INT
CSZ
DDC_DAT
ST_DET1
SCL
HWRESET
DDC_CLK
Volume
VCC5V
VCC12V
VCPU
RXD
TXD
AD0
AD1
AD2
AD3
DDC_WPDVI_DET
DDCCI_SEL
VAA3
VLCD
TOP
B
TSU16/56AK FOR MYSON 512 SWITCH
B
16Wednesday, March 09, 2005
Title
Size Document Number Rev
Date: Sheet of
VLCD
VAA1
VCC1.8
VCC12V
VCC2.5
PB[0..9]
VCC5V
VAA2
VCC5V
VCPU
VAA4
VCC3.3
B4
2.POWER
onPanel_5V/3.3V
onBACKLITE
AdjBACKLITE
VCC3.3
VCC2.5
VAA1
VAA2
VAA3
VAA4
VCC5V
VCC12V
VLCD
VCPU
VAA3
VCC12V
VAA2
TSU16/56AK SCHEMATIC
B5
5.PANEL INTERFACE
VLCD
PB[0..9]
PA[0..9]
VAA4
VCPU
B2
4.SCALER
RIN
GIN
SOG
BIN
GNDR
GNDG
GNDB
HSYNC
VSYNC
R+
R-
G-
G+
B+
B-
CLK+
CLK-
CSZ
SCL
SDA
HWRESET
INT
Volume
AdjBACKLITE
PA[0..9]
PB[0..9]
VCC2.5
VCC3.3
VAA1
VAA2
VAA3
VAA4
AD0
AD1
AD2
AD3
VAA1
http://www.wjel.net

ASUS MM19D
20
CN201
CONN
2
4
6
8
10
12
1
3
5
7
9
11
Q204
PMBS3904
CE
B
H1
H8D3.5-2LX
1 2 3
4
5
6 7 8
9
1 2 3
4
5
6 7 8
9
VCC5V+
VCC12V
H4
H8D3.5-2LX
1 2 3
4
5
6 7 8
9
1 2 3
4
5
6 7 8
9
R201 4.7K 1/16W
VCC1.8 4
+
C211
47uF/16V
D202
GS1D
R209
0 1/16W
H2
H8D3.5-2LX
1 2 3
4
5
6 7 8
9
1 2 3
4
5
6 7 8
9
R215
150K 1/16W
VAA2 4
VCC3.3
VLCD 5 VAA3
C205
0.1uF
VAA4
C207
0.1uF
DIM
R212 4.7K 1/16W
SOT-252
VCPU
GND
D201 SS14
R204
10K 1/16W
VCC5V
VCC5V+
VCC3.3
FB202
600 OHM
VAA4 4
GND
C217
1uF/50V
U202
AIC1084-33M
3
1
2
VIN
ADJ
VOUT
Q203
AO3401
R208
10K 1/16W
+
C204
220uF/25V
+
C215
47uF/16V
VCPU 6
GND
VCC5V 3,4,6
VCC5V
POWER
B
TSU16/56AK FOR MYSON 512 SWITCH
B
26Wednesday, March 09, 2005
Title
Size Document Number Rev
Date: Sheet of
GND
C210
0.1uF
C
BE
+
C202
220uF/25V
R206
10K 1/16W
VCC5V+
FB201
NC
onBACKLITE 6
VCC5V
VCC1.8
VCC12V
R210
NC
TO-263
C
BE
R214
NC
C203
0.1uF
C201
0.1uF
VAA2
R213
NC
VCC3.3 4
U201
AZ1117D-1.8
3 2
1
VI VO
GND
VAA3 4
VCC5V
C214
0.1uF
C216
0.1uF
VAA1 4
VCC12V
+
C208
10uF/16V
VCC5V
VCC12V
R202
10K 1/16W
Brightness
R205 4.7K 1/16W
Q201
PMBS3904
CE
B
VAA1
C212
0.1uF
VLCD
AdjBACKLITE4
onPanel_5V/3.3V6
Q202
PMBS3904
CE
B
VCC12V 6
VCC5V
VCC5V
ON_OFF
VCC5V
GND
VCPU
VCC12V
C206
1uF/25V
R211
10K 1/16W
R203
1K 1/16W
GND
R207 4.7K 1/16W
http://www.wjel.net