Asus P4P8X SE User manual

Motherboard
P4P8X SE
User Guide

ii
Checklist
Copyright © 2003 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language in any form or by any means, except documentation kept by the purchaser for
backup purposes, without the express written permission of ASUSTeK COMPUTER INC.
(“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or
altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2)
the serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES
OR CONDITIONS OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE.
IN NO EVENT SHALLASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE
LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
(INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE
OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR
ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUALARE FURNISHED
FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGEATANY TIME
WITHOUT NOTICE,AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BYASUS.
ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR
INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS
AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identification or
explanation and to the owners’ benefit, without intent to infringe.
E1479
First Edition
November 2003

iii
Features
Contents
Notices ............................................................................................v
Safety information ..........................................................................vi
About this guide............................................................................. vii
ASUS contact information ............................................................ viii
P4P8X SE specifications summary ................................................ix
Chapter 1: Product introduction
1.1 Welcome! ........................................................................... 1-2
1.2 Package contents............................................................... 1-2
1.3 Special features.................................................................. 1-3
1.4 Motherboard components .................................................. 1-5
1.5 Motherboard layout ............................................................ 1-9
1.6 Before you proceed .......................................................... 1-10
1.7 Motherboard installation ....................................................1-11
1.7.1 Placement direction ..............................................1-11
1.7.2 Screw holes ..........................................................1-11
1.8 Central Processing Unit (CPU)......................................... 1-12
1.8.1 Overview .............................................................. 1-12
1.8.2 Installing the CPU ................................................ 1-13
1.9 System memory ............................................................... 1-14
1.9.1 Memory configurations ........................................ 1-14
1.9.2 Installing a DIMM ................................................. 1-16
1.10 Expansion slots ................................................................ 1-17
1.10.1 Standard interrupt assignments ........................... 1-17
1.10.2 PCI slots .............................................................. 1-18
1.10.3 AGP slot............................................................... 1-18
1.11 Jumpers............................................................................ 1-19
1.12 Connectors ....................................................................... 1-21
Chapter 2: BIOS information
2.1 Managing and updating your BIOS .................................... 2-2
2.1.1 Creating a bootable floppy disk ............................. 2-2
2.1.2 Using AFUDOS to update the BIOS ...................... 2-2
2.1.3 Using ASUS EZ Flash to update the BIOS ............ 2-4
2.1.4 Recovering the BIOS with CrashFree BIOS 2 ....... 2-5
2.2 BIOS Setup program .......................................................... 2-7
2.2.1 BIOS menu screen ................................................ 2-8

iv
Safeguards
Contents
2.2.2 Menu bar................................................................ 2-8
2.2.3 Navigation keys ..................................................... 2-8
2.2.4 Menu items ............................................................ 2-9
2.2.5 Sub-menu items..................................................... 2-9
2.2.6 Configuration fields ................................................ 2-9
2.2.7 Pop-up window ...................................................... 2-9
2.2.8 Scroll bar................................................................ 2-9
2.2.9 General help .......................................................... 2-9
2.3 Main menu........................................................................ 2-10
2.3.1 System Time [xx:xx:xxxx]..................................... 2-10
2.3.2 System Date [Day xx/xx/xxxx] ............................. 2-10
2.3.3 Legacy Diskette A [1.44M, 3.5 in.] ....................... 2-10
2.3.4 Primary/Secondary/Third/
FourthIDE Master/Slave .......................................2-11
2.3.5 IDE Configuration ................................................ 2-12
2.3.6 System Information .............................................. 2-14
2.4 Advanced menu ............................................................... 2-15
2.4.1 JumperFree Configuration ................................... 2-15
2.4.2 CPU Configuration ............................................... 2-17
2.4.3 Chipset................................................................. 2-18
2.4.4 Onboard Devices Configuration........................... 2-20
2.4.5 PCI PnP ............................................................... 2-22
2.4.6 USB Configuration ............................................... 2-23
2.5 Power menu ..................................................................... 2-25
2.5.1 Suspend Mode [Auto] .......................................... 2-25
2.5.2 Repost Video on S3 Resume [No] ....................... 2-25
2.5.3 ACPI 2.0 Support [No] ......................................... 2-25
2.5.4 ACPI APIC Support [Enabled] ............................. 2-25
2.5.5 BIOS -> AMLACPI Table [Enabled] ..................... 2-25
2.5.6 APM Configuration............................................... 2-26
2.5.7 Hardware Monitor ................................................ 2-28
2.6 Boot menu ........................................................................ 2-29
2.6.1 Boot Device Priority ............................................. 2-29
2.6.2 Boot Settings Configuration ................................. 2-30
2.6.3 Security ................................................................ 2-31
2.7 Exit menu ......................................................................... 2-34
Chapter 3: Software support
3.1 Install an operating system................................................. 3-2
3.2 Support CD information...................................................... 3-2
3.3 AI Net ................................................................................. 3-5

v
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
The use of shielded cables for connection of the monitor to the
graphics card is required to assure compliance with FCC regulations.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.

vi
Safety information
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from
the electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that
the power cables for the devices are unplugged before the signal
cables are connected. If possible, disconnect all power cables from the
existing system before you add a device.
• Before connecting or removing signal cables from the motherboard,
ensure that all power cables are unplugged.
• Seek professional assistance before using an adpater or extension
cord. These devices could interrupt the grounding circuit.
• Make sure that your power supply is set to the correct voltage in your
area. If you are not sure about the voltage of the electrical outlet you
are using, contact your local power company.
• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Operation safety
• Before installing the motherboard and adding devices on it, carefully
read all the manuals that came with the package.
• Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the
product in any area where it may become wet.
• Place the product on a stable surface.
• If you encounter technical problems with the product, contact a
qualified service technician or your retailer.

vii
About this guide
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the
following symbols used throughout this manual.
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
1. ASUS Websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. The ASUS websites are listed in the
ASUS Contact Information on page viii.
2. Optional Documentation
Your product package may include optional documentation, such as
warranty flyers, that may have been added by your dealer. These
documents are not part of the standard package.
WARNING: Information to prevent injury to yourself when trying
to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Information that you MUST follow to complete a
task.
NOTE: Tips and additional information to aid in completing a task.

viii
ASUS contact information
ASUSTeK COMPUTER INC. (Asia-Pacific)
Address 150 Li-Te Road, Peitou, Taipei, Taiwan 112
Telephone [phone]
Web site www.asus.com.tw
Technical Support
Telephone(MB/Component) [phone] (English)
(Notebook) [phone] (English)
(Server/PC) [phone] (English)
(Networking) [phone] (English)
Support fax [phone]
ASUS COMPUTER INTERNATIONAL (America)
Address 44370 Nobel Drive, Fremont, CA 94538, USA
Fax [phone]
E-mail [email protected]
Web site usa.asus.com
Technical Support
Telephone (General) [phone]
(Notebook) [phone]
Support fax [phone]
Support e-mail [email protected]
ASUS COMPUTER GmbH (Germany and Austria)
Address Harkort Str. 25, D-40880 Ratingen, Germany
Telephone [phone]
Fax [phone]
Online contact www.asuscom.de/sales
Technical Support
Telephone [phone]
Fax [phone]
Online support www.asuscom.de/support
Web site www.asuscom.de/news
ASUS COMPUTER (Middle East and North Africa)
Address P.O. Box 64133, Dubai, U.A.E.
Telephone [phone]
Fax [phone]
Web site www.ASUSarabia.com

ix
P4P8X SE specifications summary
CPU
Chipset
Front Side Bus (FSB)
Memory
Expansion slots
IDE
RAID IDE / Serial ATA
(optional)
IEEE 1394 (optional)
Audio (optional)
LAN (optional)
Socket 478 for Intel
®
Pentium
®
4 / Celeron up to 3.2 GHz+
Supports Intel
®
Hyper-Threading Technology
North Bridge: Intel 865P MCH
South Bridge: Intel ICH5
800*/533/400 MHz (*Overclocked)
Dual channel memory architecture
4 x 184-pin DDR DIMM sockets for up to 4GB memory
Supports PC3200*/PC2700/PC2100 unbuffered non-ECC
DDR DIMMs (*Overclocking mode)
1 x AGP 8X
5 x PCI
2 x UltraDMA100 support for 4 drives
2 x SerialATA
ADI AD1888 SoundMAX 6-channel audio CODEC
Supports S/PDIF out interface
Marvell
®
88E8001 Gigabit LAN controller
Integrated 8 USB 2.0 ports
Power Loss Restart
ASUS EZ Flash
ASUS CrashFree BIOS 2
ASUS MyLogo2
ASUS JumperFree
ASUS C.P.R. (CPU Parameter Recall)
Adjustable CPU, memory and AGP voltages
SFS (Stepless Frequency Selection) at 1MHz increments
Adjustable FSB/DDR ratio, Fixed AGP/PCI frequencies
1 x Parallel port
1 x Serial port
1 x PS/2 keyboard port
1 x PS/2 mouse port
4 x USB 2.0/USB 1.1 ports
1 x RJ-45 port
1 x S/PDIF-out port
Line In/Line Out/Microphone ports
(continued on the next page)
CPU
Chipset
Front Side Bus (FSB)
Memory
Expansion slots
Storage
Audio
Gigabit LAN
USB 2.0
Special Features
Overclocking
Features
Rear Panel I/O

x
P4P8X SE specifications summary
* Specifications are subject to change without notice.
Internal I/O
BIOS features
Industry standard
Manageability
Form Factor
Support CD contents
2 x USB 2.0/1.1 connector for 4 additional USB ports
2 x Serial ATA connectors
CPU/Chassis fan connectors
20-pin/4-pin ATX 12V power connectors
Chassis intrusion
GAME/MIDI connector
CD/AUX audio connectors
Front panel audio connector
4Mb Flash ROM, AMI BIOS, PnP, DMI2.0, ACPI, SM
BIOS2.3, ASUS C.P.R., ASUS EZ Flash
PCI 2.2, USB 2.0
WfM 2.0, DMI 2.0, WOL/WOR by PME, chassis intrusion
ATX form factor: 12 in x 9.6 in
Device drivers
ASUS PC Probe
ASUS LiveUpdate
Trend Micro™ PC-cillin 2002 anti-virus software

Chapter 1
This chapter describes the features of the
P4P8X SE motherboard. It includes brief
descriptions of the motherboard components,
and illustrations of the layout, jumper settings,
and connectors.
Product introduction

1-2 Chapter 1: Product introduction
1.1 Welcome!
Thank you for buying the ASUS
®
P4P8X SE motherboard!
The motherboard delivers a host of new features and latest technologies making it
another standout in the long line of ASUS quality motherboards!
The motherboard incorporates the Intel
®
Pentium
®
4 / Celeron Processor in 478-
pin package coupled with the Intel
®
865P chipset to set a new benchmark for an
effective desktop platform solution.
Supporting up to 4GB of system memory with PC3200*/2700/2100 DDR SDRAM,
an AGP 8X slot, Serial ATA support, USB 2.0, and 6-channel audio features, the
P4P8X SE is your affordable vehicle to enter the world of computing!
Before you start installing the motherboard, and hardware devices on it, check the
items in your package with the list below. (* Overclocking mode)
1.2 Package contents
Check your P4P8X SE package for the following items.
If any of the above items is damaged or missing, contact your retailer.
ASUS P4P8X SE motherboard
ASUS motherboard support CD
2 x Serial ATA cable
UltraDMA 100/66 cable
Floppy disk cable
I/O shield
Bag of extra jumper caps
User Guide
Jumpers and connectors sticker (Retail boxes only)

ASUS P4P8X SE motherboard user guide 1-3
1.3 Special features
Latest processor technology
The motherboard supports the Intel
®
Pentium
®
4 / Celeron Processors with 512KB L2
cache and an 533/400 MHz system bus. The CPU features the Intel Hyper-
Threading Technology and a new power design that allows up to 3.2GHz core
frequencies. The motherboard will also support the next generation Intel Prescott
CPU.
Dual-channel DDR333 memory support
The motherboard supports up to 4GB of system memory using PC3200*/2700/
2100 non-ECC DDR DIMMs to deliver up to 3.2GB/s data transfer rate for the
latest 3D graphics, multimedia, and Internet applications. (*Overclocking mode)
Serial ATA technology
The motherboard bundles the new Serial ATA technology through the SATA
interfaces onboard. The SATA specification allows for thinner, more flexible cables
with lower pin count, reduced voltage requirement, up to 150 MB/s data transfer
rate, and software compatibility with the legacy Parallel ATA.
AGP 8X support
The motherboard also mounts an AGP 8X interface (a.k.a.AGP 3.0), offering
2.1GB/s bandwidth.
CrashFree BIOS 2
This feature allows you to restore the original BIOS data from the support CD, or
from a bootable floppy disk, when the BIOS codes and data are corrupted. This
protection eliminates the need to buy a replacement ROM chip.
ASUS EZ Flash BIOS
With the ASUS EZ Flash, you can easily update the system BIOS even before
loading the operating system. No need to use a DOS-based utility or boot from a
floppy disk.
Gigabit LAN solution
The motherboard supports Gigabit LAN by integrating the Marvell 88E8001 Gigabit
LAN controller, equipped with a unique net-diagnosing utility - VCT (Virtual Cable
Tester). VCT intelligently diagnoses and reports cable faults from a remote location
up to 100 meters and helps users improve network quality.

1-4 Chapter 1: Product introduction
USB 2.0 technology
The motherboard implements the new Universal Serial Bus (USB) 2.0
specification, extending the connection speed from 12 Mbps on USB 1.1 to a fast
480 Mbps on USB 2.0.
6-channel digital audio
The ADI AD1888 SoundMAX AC’97 audio CODEC is onboard to provide 6-channel
audio playback for 5.1 surround sound and over 90dB dynamic range.
Windows 98SE/ME/2000/XP support 6/4/2-channel audio modes.

ASUS P4P8X SE motherboard user guide 1-5
1.4 Motherboard components
Before you install the motherboard, learn about its major components and
available features to facilitate the installation and future upgrades. Refer to the
succeeding pages for the component descriptions.
1. ATX 12V connector
2. CPU socket
3. North Bridge controller
4. DDR DIMM sockets
5. ATX power connector
6. Super I/O controller
7. Floppy disk connector
8. IDE connectors
9. AGP 8X slot
10. SATA connectors
11. Flash ROM
12. South Bridge controller
13. Standby power LED
14. PCI slots
15. Audio CODEC
16. LAN controller
17. PS/2 mouse port
18. Parallel port
19. RJ-45 port
20. Line In jack
21. Line Out jack
22. Microphone jack
23. USB 2.0 ports 3 and 4
24. USB 2.0 ports 1 and 2
25. Serial port
26. S/PDIF out port
27. Keyboard port
See page 1-6 for the specifications of each component.

1-6 Chapter 1: Product introduction
43
16
2
12
5
8
11
14
15
1
7
9
13
1
0
6
17
27
2
0
2
1
2
2
23
18 19
2526 24

ASUS P4P8X SE motherboard user guide 1-7
ATX 12V connector. This power connector connects the 4-pin 12V plug from
theATX 12V power supply.
CPU socket. A478-pin surface mount, Zero Insertion Force (ZIF) socket for
the Intel
®
Pentium
®
4 Processor, with 800*/533/400 MHz system bus that
allows 4.3GB/s, and 3.2GB/s data transfer rates, respectively.
(*Overclocking mode)
North bridge controller. The Intel
®
82865P Memory Controller Hub (MCH)
provides the processor interface with 533/400 MHz frequency, system
memory interface at 333/266MHz operation and an AGP interface that
supportsAGP 3.0 specification including 8X Fast Write protocol. The MCH
interconnects to the south bridge ICH5 via the Intel
®
proprietary Hub Interface.
DDR DIMM sockets. These four 184-pin DIMM sockets support up to 4GB
system memory using unbuffered non-ECC PC3200*/2700/2100 DDR
DIMMs. (*Overclocking mode)
ATX power connector. This 20-pin connector connects to anATX power
supply. The power supply must have at least 1Aon the +5V standby lead
(+5VSB).
Super I/O controller. This Winbond Low Pin Count (LPC) interface provides
the commonly used Super I/O functionality. The chipset supports a high-
performance floppy disk controller for a 360K/720K/1.44M/2.88M floppy disk
drive, a multi-mode parallel port, two standard compatible UARTs, and a Flash
ROM interface. This controller also integrates the ASIC for PC health
monitoring.
Floppy disk connector. This connector accommodates the provided ribbon
cable for the floppy disk drive. One side of the connector is slotted to prevent
incorrect insertion of the floppy disk cable.
IDE connectors. These dual-channel bus master IDE connectors support
Ultra DMA100/66, PIO Modes 3 & 4 IDE devices. Both the primary (blue) and
secondary (black) connectors are slotted to prevent incorrect insertion of the
IDE ribbon cable.
AGP 8X slot. This Accelerated Graphics Port (AGP) slot supports 0.8V/1.5V
AGP 8X mode graphics cards for 3D graphical applications.
SATA connectors. These connectors support Serial ATA HDDs and allows
for up to 150MB/s data transfer rate, faster than the standard ParallelATA
with 133 MB/s.
Flash ROM. This 4Mb firmware contains the programmable BIOS program.
South bridge controller. The fifth-generation Intel I/O Controller Hub (ICH5)
is a subsystem that integrates various I/O functions including 2-channel
ATA100 bus master IDE controller, up to eight USB 2.0/1.1 ports, I/OAPIC,
SMBus 2.0 controller, LPC interface,AC’97 2.2 interface, and PCI 2.2
interface. The ICH5 also contains the necessary arbitration and buffering for
efficient utilization of these interfaces.
Standby power LED. This LED lights up if there is a standby power on the
motherboard. This LED acts as a reminder to turn off the system power before
plugging or unplugging devices.
11
12
13
10
9
8
7
6
5
4
3
2
1

1-8 Chapter 1: Product introduction
USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports
are available for connecting USB 2.0 devices.
USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports
are available for connecting USB 2.0 devices.
Serial port. This 9-pin COM1 port is for pointing devices or other serial
devices.
S/PDIF jack. This jack connects to external audio output devices.
PS/2 keyboard port. This purple connector is for a PS/2 keyboard.
PCI slots. These five 32-bit PCI 2.2 expansion slots support bus master
PCI cards like SCSI or LAN cards with 133MB/s maximum throughput.
Audio CODEC. The ADI AD1888 SoundMAX is an AC’97 CODEC that
allows 6-channel audio playback. The audio CODEC provides six DAC
channels for 5.1 surround sound, S/PDIF output, AUX and Line In stereo
inputs, integrated headphone amplifier, and supports greater than 90dB
dynamic range.
LAN controller. This Marvell
®
88E8001 Gbit PCI LAN controller support
10BASE/100BASE/1000BASE-TX networking.
PS/2 mouse port. This green 6-pin connector is for a PS/2 mouse.
Parallel port. This 25-pin port connects a parallel printer, a scanner, or other
devices.
RJ-45 port. This port allows connection to a Local Area Network (LAN)
through a network hub.
Line In jack. This Line In (light blue) jack connects a tape player or other
audio sources. In 6-channel mode, the function of this jack becomes Rear
Speaker out.
Line Out jack. This Line Out (lime) jack connects a headphone or a
speaker. In 6-channel mode, the function of this jack becomes Front
Speaker Out.
Microphone jack. This Mic (pink) jack connects a microphone. In 6-channel
mode, the function of this jack becomes Bass/Center Speaker Out.
15
16
17
18
19
20
22
21
23
24
25
26
27
14
Audio 2, 4 or 6-channel configuration
Headphone/
2-Speaker 4-Speaker 6-Speaker
Light Blue Line In Rear Speaker Out Rear Speaker Out
Lime Line Out Front Speaker Out Front Speaker Out
Pink Mic In Mic In Bass/Center Speaker Out
The functions of the Line Out, Line In, and Microphone jacks change when you
select the 6-channel audio configuration as shown in the following table:

ASUS P4P8X SE motherboard user guide 1-9
1.5 Motherboard layout
PCI1
PANEL1
P4P8X SE
®
CR2032 3V
Lithium Cell
CMOS Power
CD1
AUX1
Super
I/O
4Mbit
Firmware
Hub
PS/2KBMS
T: Mouse
B: Keyboard
Below:Mic In
Center:Line Out
Top:Line In
Accelerated Graphics Port (AGP1)
CPU_FAN1
FP_AUDIO
Audio
Codec
USB2.0
T: USB3
B: USB4
Top:
RJ-45
GAME1
Socket 478
ATX12V1
CHASSIS1
DDR DIMM_B1 (64 bit,184-pin module)
PCI2
PCI3
PCI4
PCI5
CLRTC1
FLOPPY1
PRI_IDE1
SEC_IDE1
PARALLEL PORT
COM1
SPDIF_O
ATX Power Connector
DDR DIMM_A1 (64 bit,184-pin module)
DDR DIMM_A2 (64 bit,184-pin module)
DDR DIMM_B2 (64 bit,184-pin module)
KBPWR
CHA_FAN1
Intel
ICH5
Intel
82865P
Memory
Controller
Hub
Marrell
88E8001
SATA1
USB_56 USB_78
SB_PWR1
SATA2
USBPW12
USBPW34
USBPW56
USBPW78
24.5cm (9.6in)
30.5cm (12.0in)
USB20_12

1-10 Chapter 1: Product introduction
1.6 Before you proceed
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any
component.
2. Use a grounded wrist strap or touch a safely grounded object or to a metal
object, such as the power supply case, before handling components to
avoid damaging them due to static electricity.
3. Hold components by the edges to avoid touching the ICs on them.
4. Whenever you uninstall any component, place it on a grounded antistatic
pad or in the bag that came with the component.
5. Before you install or remove any component, ensure that the ATX
power supply is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
When lit, the standby power LED (SB_PWR1) indicates that the system is ON,
in sleep mode, or in soft-off mode, a reminder that you should shut down the
system and unplug the power cable before removing or plugging in any
motherboard component.
P4P8X SE
®
P4P8X SE Onboard LED
SB_PWR1
ON
Standby
Power
OFF
Powere
d
Off