Asus RS100-E10-PI2 User manual

1U Rackmount Server
User Guide
RS100-E10-PI2

ii
Copyright © 2020 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form or by any means,
except documentation kept by the purchaser for backup purposes, without the express written permission
of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS provides this manual “as is” without warranty of any kind, either express or implied, including but not
limited to the implied warranties or conditions of merchantability or tness for a particular purpose. In no
event shall ASUS, its directors, ofcers, employees, or agents be liable for any indirect, special, incidental,
or consequential damages (including damages for loss of prots, loss of business, loss of use or data,
interruption of business and the like), even if ASUS has been advised of the possibility of such damages
arising from any defect or error in this manual or product.
Specications and information contained in this manual are furnished for informational use only, and are
subject to change at any time without notice, and should not be construed as a commitment by ASUS.
ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual,
including the products and software described in it.
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
E16272
Revised Edition V6
February 2020

iii
Contents
Safety information..................................................................................................... vii
About this guide......................................................................................................... ix
Chapter 1: Product Introduction
1.1 System package contents.........................................................................1-2
1.2 Serial number label....................................................................................1-2
1.3 System specifications ...............................................................................1-3
1.4 Front panel features...................................................................................1-5
1.5 Rear panel features....................................................................................1-5
1.6 Internal features .........................................................................................1-6
1.7 LED information .........................................................................................1-7
1.7.1 Front panel LEDs ........................................................................ 1-7
1.7.2 Rear panel LEDs......................................................................... 1-8
1.7.3 LAN (RJ-45) LEDs ...................................................................... 1-8
Chapter 2: Hardware Information
2.1 Chassis cover.............................................................................................2-2
2.1.1 Removing the chassis cover ....................................................... 2-2
2.1.2 Reinstalling the chassis cover..................................................... 2-3
2.2 Central Processing Unit (CPU) ................................................................. 2-5
2.2.1 Installing the CPU ....................................................................... 2-5
2.2.2 Installing the CPU heatsink......................................................... 2-8
2.3 System memory .......................................................................................2-10
2.3.1 Overview ................................................................................... 2-10
2.3.2 Memory congurations.............................................................. 2-10
2.3.3 Installing a DIMM on a single clip DIMM socket........................ 2-11
2.4 Hard disk drives .......................................................................................2-13
2.4.1 Installing a hard disk drive to the HDD bay 1............................ 2-13
2.4.2 Installing 2.5-inch SSDs on HDD bay 1 (Optional).................... 2-17
2.4.3 Installing a 3.5-inch Serial ATA HDD to HDD bay 2.................. 2-20
2.4.4 Installing 2.5-inch SSDs on HDD bay 2 (Optional).................... 2-23
2.5 Expansion card ........................................................................................2-26
2.5.1 Installing an expansion card...................................................... 2-26
2.5.2 Conguring an expansion card ................................................. 2-28
2.5.3 Installing M.2 (NGFF) cards...................................................... 2-29

iv
Contents
2.6 Cable connections ...................................................................................2-30
2.7 Removable/optional components...........................................................2-31
2.7.1 System fans .............................................................................. 2-31
2.7.2 Optical disk drive (optional)....................................................... 2-32
2.7.3 Installing ASMB9 series management card (optional) .............. 2-33
Chapter 3: Installation Options
3.1 Rackmount rail kit items ........................................................................... 3-2
3.2 Attaching the rails to the rack ..................................................................3-2
Chapter 4: Motherboard Information
4.1 Before you proceed ...................................................................................4-2
4.2 Motherboard overview............................................................................... 4-3
4.2.1 Placement direction..................................................................... 4-3
4.2.2 Screw holes................................................................................. 4-3
4.2.3 Motherboard layout ..................................................................... 4-4
4.2.4 Layout contents........................................................................... 4-5
4.3 Onboard LEDs............................................................................................4-7
4.4 Jumpers ....................................................................................................4-10
4.5 Connectors ...............................................................................................4-15
4.5.1 Rear panel connectors.............................................................. 4-15
4.5.2 Q-Code table............................................................................. 4-17
4.5.3 Internal connectors.................................................................... 4-19
Chapter 5: BIOS Setup
5.1 Managing and updating your BIOS .......................................................... 5-2
5.1.1 ASUS CrashFree BIOS 3 utility................................................... 5-2
5.1.2 ASUS EzFlash Utility................................................................... 5-3
5.1.3 BUPDATER utility ....................................................................... 5-4
5.2 BIOS setup program ..................................................................................5-6
5.2.1 BIOS menu screen...................................................................... 5-7
5.2.2 Menu bar..................................................................................... 5-7
5.2.3 Menu items.................................................................................. 5-8
5.2.4 Submenu items ........................................................................... 5-8
5.2.5 Navigation keys........................................................................... 5-8
5.2.6 General help................................................................................ 5-8
5.2.7 Conguration elds ..................................................................... 5-8
5.2.8 Pop-up window............................................................................ 5-8
5.2.9 Scroll bar..................................................................................... 5-8

v
Contents
5.3 Main menu ..................................................................................................5-9
5.4 Performance Tuning menu......................................................................5-10
5.5 Advanced menu .......................................................................................5-11
5.5.1 CPU Conguration .................................................................... 5-12
5.5.2 Power & Performance............................................................... 5-14
5.5.3 Server ME Conguration........................................................... 5-16
5.5.4 Trusted Computing.................................................................... 5-16
5.5.5 APM Conguration.................................................................... 5-17
5.5.6 Runtime Error Logging Settings................................................ 5-17
5.5.7 Onboard LAN Conguration...................................................... 5-18
5.5.8 Serial Port Console Redirection................................................ 5-19
5.5.9 Intel TXT Information................................................................. 5-21
5.5.10 PCI Subsystem Settings ........................................................... 5-22
5.5.11 USB Conguration .................................................................... 5-23
5.5.12 Network Stack Conguration..................................................... 5-24
5.5.13 CSM Conguration.................................................................... 5-25
5.5.14 NVMe Conguration.................................................................. 5-26
5.5.15 WHEA Conguration................................................................. 5-26
5.5.16 Tls Auth Conguration............................................................... 5-27
5.5.17 iSCSI Conguration .................................................................. 5-27
5.6 Chipset menu ...........................................................................................5-28
5.6.1 System Agent (SA) Conguration ............................................. 5-28
5.6.2 PCH-IO Conguration ............................................................... 5-30
5.7 Security menu ..........................................................................................5-32
5.8 Boot menu ................................................................................................5-35
5.9 Monitor menu ...........................................................................................5-37
5.10 Tool menu.................................................................................................5-38
5.11 Event Logs menu .....................................................................................5-38
5.11.1 Change Smbios Event Log Settings ......................................... 5-38
5.11.2 View Smbios Event Log ............................................................ 5-39
5.12 Server Mgmt menu...................................................................................5-40
5.12.1 System Event Log..................................................................... 5-41
5.12.2 Bmc self test log........................................................................ 5-42
5.12.3 BMC network conguration....................................................... 5-43
5.12.4 View System Event Log ............................................................ 5-44
5.12.5 BMC User Settings.................................................................... 5-44
5.13 Save & Exit menu.....................................................................................5-45

vi
Contents
Chapter 6: RAID Configuration
6.1 Setting up RAID.......................................................................................... 6-2
6.1.1 RAID denitions .......................................................................... 6-2
6.1.2 Installing hard disk drives............................................................ 6-3
6.1.3 Setting the RAID mode in BIOS.................................................. 6-3
6.1.4 RAID conguration utilities.......................................................... 6-3
6.2 Intel®Rapid Storage Technology enterprise
SATA Option ROM Utility........................................................................... 6-4
6.2.1 Creating a RAID set .................................................................... 6-5
6.2.2 Deleting a RAID set..................................................................... 6-7
6.2.3 Resetting disks to Non-RAID ...................................................... 6-8
6.2.4 Exiting the Intel®Rapid Storage Technology enterprise
SATA Option ROM utility............................................................. 6-9
6.2.5 Rebuilding the RAID.................................................................... 6-9
6.2.6 Setting the Boot array in the BIOS Setup Utility........................ 6-11
6.3 Intel®Rapid Storage Technology enterprise (Windows)...................... 6-12
6.3.1 Creating a RAID set .................................................................. 6-13
6.3.2 Changing a Volume Type.......................................................... 6-15
6.3.3 Deleting a volume ..................................................................... 6-16
6.3.4 Preferences............................................................................... 6-17
Chapter 7: Driver Installation
7.1 RAID driver installation .............................................................................7-2
7.1.1 Creating a USB ash drive with RAID drive................................ 7-2
7.1.2 Installing the RAID controller driver............................................. 7-2
7.2 Management applications and utilities installation ................................ 7-5
7.3 Running the Support DVD......................................................................... 7-5
7.4 Installing the system drivers.....................................................................7-6
Appendix
P11C-M/4L block diagram ...................................................................................... A-2
Notices .................................................................................................................... A-3
ASUS contact information...................................................................................... A-6

vii
Safety information
Electrical Safety
• Before installing or removing signal cables, ensure that the power cables for the system
unit and all attached devices are unplugged.
• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
• When adding or removing any additional devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are connected. If
possible, disconnect all power cables from the existing system before you add a device.
• If the power supply is broken, do not try to x it by yourself. Contact a qualied service
technician or your dealer.
Operation Safety
• Any mechanical operation on this server must be conducted by certied or experienced
engineers.
• Before operating the server, carefully read all the manuals included with the server
package.
• Before using the server, ensure all cables are correctly connected and the power cables
are not damaged. If any damage is detected, contact your dealer as soon as possible.
• To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Place the server on a stable surface.
This product is equipped with a three-wire power cable and plug for the user’s safety. Use
the power cable with a properly grounded electrical outlet to avoid electrical shock.

viii
To prevent exposure to the optical drive’s laser, do not attempt to disassemble or repair the
optical drive by yourself. For your safety, contact a professional technician for assistance.
CLASS 1 LASER PRODUCT
Optical Drive Safety Information
Laser Safety Information
Heavy System
CAUTION! This server system is heavy. Ask for assistance when moving
or carrying the system.
Lithium-Ion Battery Warning
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.

ix
About this guide
Audience
This user guide is intended for system integrators, and experienced users with at least basic
knowledge of conguring a server.
Contents
This guide contains the following parts:
1. Chapter 1: Product Introduction
This chapter describes the general features of the server, including sections on front
panel and rear panel specications.
2. Chapter 2: Hardware Information
This chapter lists the hardware setup procedures that you have to perform when
installing or removing system components.
3. Chapter 3: Installation Options
This chapter describes how to install optional components into the barebone server.
4. Chapter 4: Motherboard Information
This chapter includes the motherboard layout and brief descriptions of the jumpers and
internal connectors.
5. Chapter 5: BIOS Setup
This chapter tells how to change system settings through the BIOS Setup menus and
describes the BIOS parameters.
6. Chapter 6: RAID Configuration
This chapter provides instructions for setting up, creating and conguring RAID sets
using the available utilities.
7. Chapter 7: Driver Installation
This chapter provides instructions for installing the necessary drivers for different
system components.

x
References
Refer to the following sources for additional information, and for product and software
updates.
1. ASUS Control Center (ACC) user guide
This manual tells how to set up and use the proprietary ASUS server management
utility.
2. ASUS websites
The ASUS websites worldwide provide updated information for all ASUS hardware and
software products. Refer to the ASUS contact information.
Conventions
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
Typography
Bold text Indicates a menu or an item to select.
Italics Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than
sign means that you must press the enclosed key.
Example: <Enter> means that you must press
the Enter or Return key.
<Key1>+<Key2>+<Key3> If you must press two or more keys simultaneously,
the key names are linked with a plus sign (+).
Example: <Ctrl>+<Alt>+<Del>
Command Means that you must type the command
exactly as shown, then supply the required
item or value enclosed in brackets.
Example: At the DOS prompt, type the
command line: format A:/S
DANGER/WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when
trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.

1
Product Introduction
This chapter describes the general features of
the server, including sections on front panel and
rear panel specications.
Chapter 1: Product Introduction

Chapter 1: Product Introduction
1-2
If any of the above items is damaged or missing, contact your retailer.
1.1 System package contents
Check your system package for the following items.
1.2 Serial number label
Before requesting support from the ASUS Technical Support team, take note of the product’s
12-character serial number as seen in the example xxS0xxxxxxxx below. With the correct
serial number of the product, ASUS Technical Support team members can quickly identify the
server model and provide a satisfactory solution to your technical issue.
Model Name RS100-E10-PI2
Chassis ASUS R09 1U Rackmount Chassis
Motherboard ASUS P11C-M/4L Server Board
Component 1 x 250W Single Power Supply or
1 x 350W Single Power Supply*
2 x SATA Cables
1 x PCI Express x16 Riser Card
1 x Front I/O Board
3 x System Fans (40mm x 28mm)
1 x Fan Mylar
* This item may vary according to model.
Accessories 1 x RS100-E10-PI2 Support DVD (with User's Guide)
1 x ACC Instruction Card
1 x Bag of Screws
1 x AC Power Cable
1 x CPU Heatsink
Optional Items ASUS ASMB9-iKVM Remote management card
Slim-type DVD-ROM/DVD RW
Ball Bearing Rail Kit
2.5" SSD drive tray with Power and SATA cable
1 x Expansion card Fan Duct
4 3 2 1
Q-Code
1
2
3
4
xxS0xxxxxxxx
RS100-E10-PI2

ASUS RS100-E10-PI2 1-3
1.3 System specifications
The ASUS RS100-E10-PI2 is a 1U barebone server system featuring the ASUS P11C-M/4L
server board.
Model Name RS100-E10-PI2
Processor / System Bus
1 x Socket LGA1151
Intel®Xeon® processor E-21xx / E-22xx product family (95W)
Intel®8th/9th Generation Core™ i3 processors
Core Logic Intel®C242 Chipset
Memory
Total Slots 4 (2 Channels)
Capacity Maximum up to 128GB (UDIMM)
Memory Type DDR4 2666/2400 ECC/non-ECC UDIMM
* Refer to ASUS server AVL for the latest update
Memory Size 32GB, 16GB, 8GB, 4GB (UDIMM)
Expansion
Slots
Total PCI/PCI-X/
PCI-E Slots 1
Slot Type 1 x PCI-E x16 (x16 Gen3 Link)
Storage
Intel®C242:
6 x SATA 6Gb/s ports with 2 * M.2 (NGFF 22110 / 2280 /
2260 / 2242, PCI-E Gen3 x2 link or SATA signal)*
Intel® RSTe (Windows & Linux)
(Support software RAID 0, 1, 10 & 5)
* When the M.2 is SATA signal, the gray SATA ports will be
disabled.
Storage Bays
With ODD:
2 x 3.5” Internal HDD Bays
(Optional 1 x 3.5” HDD + 2 x 2.5” SSD)
Without ODD:
2 x 3.5” Internal HDD Bays
(Optional 1 x 3.5” HDD + 4 x 2.5” SSD)
2 x M.2 (NGFF 22110 / 2280 / 2260 / 2242)
Networking LAN 4 x Intel®I210AT
1 x Mgmt LAN
Graphic VGA Aspeed AST2500
Auxiliary Storage FDD / CD / DVD 1 x Slim-type Optical Device Bay
(Options: No ODD / DVD-ROM / DVD-RW)
Front I/O
2 x USB 3.1 Gen 1 ports
1 x VGA port*
* The full system supports a total of 1 VGA output, the front VGA
is for the purpose of easy debugging only.
Rear I/O Ports
2 x USB 3.1 Gen 2 ports
2 x USB 3.1 Gen 1 ports
1 x VGA port
1 x External Serial Port
4 x RJ-45 ports
1 x RJ-45 ports (One for ASMB9-iKVM) (Optional)
(continued on the next page)

Chapter 1: Product Introduction
1-4
*Specifications are subject to change without notice.
Switch/LED
Rear Switch/LED:
1 x Q-Code/Port 80 LED
1 x Power switch
Front Switch/LED:
1 x Power switch/LED
1 x Location switch/LED
1 x Reset switch
1 x HDD Access LED
1 x Message LED
LAN 1-4 LED
OS Support Please nd the latest OS support from http://www.asus.com
Management
Solution
Out of Band
Remote
Hardware
Optional ASMB9-iKVM for KVM-over-IP
Software ASUS Control Center
Net Weight Kg (CPU, DRAM &
HDD not included) 7.5 Kg
Dimensions (DD x WW x HH) 380mm x 430mm x 44mm
Power Supply and Ratings
250W Single Power Supply
Rating: 100-240Vac,4A ,50-60Hz, Class I
350W Single Power Supply
Rating: 100-240Vac,6-3A ,50-60Hz, Class I
Environment
Operation temperature: 10°C–35°C
Non-operating temperature: -40°C–70°C
Non-operation humidity: 20%–90% (Non-condensing)

ASUS RS100-E10-PI2 1-5
4 3 2 1
Q-Code
1
2
3
4
4 3 2 1
Q-Code
1
2
3
4
1.4 Front panel features
This barebone server has a simple yet stylish front panel with easily accessible features. The
power and reset buttons, LED indicators, optical drive, and two USB ports are located on the
front panel.
Refer to section 1.7.1 Front panel LEDs for the LED descriptions.
Turn off the system power and detach the power supply before removing or replacing any
system component.
1.5 Rear panel features
The rear panel has the AC power socket and access to any added expansion cards. The I/O
shield with openings for the rear panel connectors on the motherboard are also found in the
rear panel.
*This port is for an ASUS ASMB9-iKVM controller card only.
Optical drive (optional)
USB 3.1 Gen 1 port
HDD Access LED
Power button Reset button
Message LED
LAN LEDs VGA port
Location button
Asset tag
VGA port
AC power socket
USB 3.1 Gen 1 ports USB 3.1 Gen 2 ports
Serial port
LAN port 1-2
LAN port 3-4LAN port 5*
Q-Code LED
Power button
Location LED
Message LED

Chapter 1: Product Introduction
1-6
1.6 Internal features
The barebone server includes the basic components as shown.
WARNING
HAZARDOUS MOVING PARTS
KEEP FINGERS AND OTHER BODY PARTS AWAY
1. PCI-E Gen3 x16 Slot with Riser Card (at x8 link)
2. System Fan
3. ASUS P11C-M/4L Server board
4. Power Supply
5. Slim-type Optical Drive (Optional)
6. HDD Bay 2
7. HDD Bay 1 (partly hidden)
Turn off the system power and detach the power supply before removing or replacing any
system component.
This barebone server does not include a oppy disk drive. Connect a USB oppy disk drive
to any of the USB ports on the front or rear panel if you need to use a oppy disk.

ASUS RS100-E10-PI2 1-7
4 3 2 1
Q-Code
1
2
3
4
1.7 LED information
1.7.1 Front panel LEDs
HDD Access LED
LAN LEDs
Power button with LED
Message LED
Location button with LED
LED Icon Display status Description
Power LED ON System power ON
HDD Access LED OFF No activity
Blinking Read/write data into the HDD
Message LED OFF System is normal; no incoming event
ON A hardware monitor event is indicated
Location LED
OFF Normal status
ON Location switch is pressed
(Press the location switch again to turn off)
LAN LEDs
OFF No LAN connection
Blinking LAN is transmitting or receiving data
ON LAN connection is present

Chapter 1: Product Introduction
1-8
1.7.3 LAN (RJ-45) LEDs
1.7.2 Rear panel LEDs
4 3 2 1
Q-Code
1
2
3
4
Message LEDLocation LED
LED Icon Display status Description
Location LED
OFF Normal status
ON Location switch is pressed
(Press the location switch again to turn off)
Message LED OFF System is normal; no incoming event
ON A hardware monitor event is indicated
LAN port LED indications
Dedicated Management LAN port (DM_LAN1) LED indications
Activity/Link LED Speed LED
Status Description Status Description
OFF No link OFF 10 Mbps connection
ORANGE Linked ORANGE 100 Mbps connection
BLINKING Data activity GREEN 1 Gbps connection
ACT/LINK
LED
SPEED
LED
Activity/Link LED Speed LED
Status Description Status Description
OFF No link OFF 10 Mbps connection
ORANGE Linked ORANGE 100 Mbps connection
BLINKING Data activity GREEN 1 Gbps connection
SPEED
LED
SPEED
LED
ACT/LINK
LED
ACT/LINK
LED

This chapter lists the hardware setup procedures that you have
to perform when installing or removing system components.
2
Hardware Information
Chapter 2: Hardware Information

Chapter 2: Hardware Information
2-2
2.1 Chassis cover
2.1.1 Removing the chassis cover
• Unplugthepowercordbeforeremovingthechassiscover.
• Takeextracarewhenremovingthechassiscover.Keepyourngersawayfrom
componentsinsidethechassisthatcancauseinjury,suchastheCPUfan,rearfan,
and parts with sharp or protruding edges.
• Theimagesofthebareboneservershowninthissectionareforreferencepurposes
onlyandmaynotexactlymatchthemodelyoupurchased.
To remove the chassis cover:
1. UseaPhillipsscrewdrivertoremovethethreescrewsonthechassiscover.
2. Firmlyholdthecoverandslideittowardtherearpanelforabouthalfaninchuntilitis
disengaged from the chassis. Then, lift the cover from the chassis.