Asus RS100-E6 PI2 User manual

1U Rackmount Server
RS100-E6/PI2
User Guide

ii
Copyright © 2009 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form or by any means,
except documentation kept by the purchaser for backup purposes, without the express written permission
of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS provides this manual “as is” without warranty of any kind, either express or implied, including but not
limited to the implied warranties or conditions of merchantability or tness for a particular purpose. In no
event shall ASUS, its directors, ofcers, employees, or agents be liable for any indirect, special, incidental,
or consequential damages (including damages for loss of prots, loss of business, loss of use or data,
interruption of business and the like), even if ASUS has been advised of the possibility of such damages
arising from any defect or error in this manual or product.
Specications and information contained in this manual ae furnished for informational use only, and are
subject to change at any time without notice, and should not be construed as a commitment by ASUS.
ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual,
including the products and software described in it.
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
E5109
First Edition
November 2009

iii
Contents
Contents ...................................................................................................... iii
Notices........................................................................................................ vii
Safety information .................................................................................... viii
About this guide ......................................................................................... ix
Chapter 1: Product introduction
1.1 System package contents........................................................... 1-2
1.2 Serial number label...................................................................... 1-2
1.3 Systemspecications ................................................................. 1-3
1.4 Front panel features..................................................................... 1-5
1.5 Rear panel features...................................................................... 1-5
1.6 Internal features ........................................................................... 1-6
1.7 LED information ........................................................................... 1-7
1.7.1 Front panel LEDs ............................................................ 1-7
1.7.2 LAN (RJ-45) LEDs .......................................................... 1-7
Chapter 2: Hardware setup
2.1 Chassis cover............................................................................... 2-2
2.1.1 Removing the chassis cover........................................... 2-2
2.1.2 Reinstalling the chassis cover......................................... 2-3
2.2 Central Processing Unit (CPU) ................................................... 2-5
2.2.1 Installing the CPU ........................................................... 2-5
2.2.2 Installing the CPU heatsink and airduct.......................... 2-8
2.3 System memory ......................................................................... 2-10
2.3.1 Overview ....................................................................... 2-10
2.3.2 Memory Congurations................................................. 2-10
2.3.3 Installing a DIMM ...........................................................2-11
2.3.4 Removing a DIMM .........................................................2-11
2.4 Hard disk drives ......................................................................... 2-12
2.4.1 Installing a hard disk drive to the HDD tray 1................ 2-12
2.4.2 Installing a hard disk drive to the HDD tray 2................ 2-13
2.5 Expansion card .......................................................................... 2-15
2.5.1 Installing an expansion card ......................................... 2-15
2.5.2 Conguring an expansion card ..................................... 2-17
2.6 Cable connections ..................................................................... 2-18
2.7 Removable/optional components............................................. 2-19
2.7.1 System fans .................................................................. 2-19

iv
Contents
2.7.2 Optical disk drive (ODD) ............................................... 2-20
2.7.3 Installing ASMB4 series management board (optional)...2-22
Chapter 3: Rackmount installation
3.1 Rackmount rail kit items.............................................................. 3-2
3.2 Attaching the rack ears ............................................................... 3-2
3.3 Attaching the rails to the rack..................................................... 3-3
Chapter 4: Motherboard Info
4.1 Motherboard layout...................................................................... 4-2
4.2 Jumpers ........................................................................................ 4-4
4.3 Internal connectors...................................................................... 4-8
Chapter 5: BIOS setup
5.1 Managing and updating your BIOS ............................................ 5-2
5.1.1 ASUS EZ Flash 2 utility................................................... 5-2
5.1.2 BUPDATER utility............................................................ 5-3
5.1.3 ASUS CrashFree BIOS 3 utility ...................................... 5-5
5.2 BIOS setup program .................................................................... 5-6
5.2.1 BIOS menu screen.......................................................... 5-7
5.2.2 Menu bar......................................................................... 5-7
5.2.3 Navigation keys............................................................... 5-7
5.2.4 Menu items ..................................................................... 5-8
5.2.5 Sub-menu items.............................................................. 5-8
5.2.6 Conguration elds ......................................................... 5-8
5.2.7 Pop-up window ............................................................... 5-8
5.2.8 Scroll bar......................................................................... 5-8
5.2.9 General help ................................................................... 5-8
5.3 Main menu .................................................................................... 5-9
5.3.1 System Time [xx:xx:xx] ................................................... 5-9
5.3.2 System Date [Day xx/xx/xxxx]......................................... 5-9
5.3.3 SATA1—6........................................................................ 5-9
5.3.4 Storage Conguration....................................................5-11
5.3.5 AHCI Conguration....................................................... 5-12
5.3.6 System Information....................................................... 5-13
5.4 Advanced menu ......................................................................... 5-14
5.4.1 CPU Conguration........................................................ 5-14

v
Contents
5.4.2 Chipset.......................................................................... 5-18
5.4.3 Onboard Devices Conguration.................................... 5-20
5.4.4 USB Conguration ........................................................ 5-21
5.4.5 PCIPnP ......................................................................... 5-22
5.4.6 ACPI Conguration ....................................................... 5-23
5.4.7 Event Log Conguration ............................................... 5-25
5.4.8 Intel VT-d Conguration [Disabled] ............................... 5-25
5.4.9 SR-IOV Supprted [Disabled]......................................... 5-25
5.5 Server menu ............................................................................... 5-26
5.6 Power menu................................................................................ 5-28
5.6.1 APM Conguration........................................................ 5-28
5.6.2 Hardware Monitor ......................................................... 5-30
5.7 Boot menu .................................................................................. 5-31
5.7.1 Boot Device Priority ...................................................... 5-31
5.7.2 Hard Disk Drives; CDROM Drives ................................ 5-31
5.7.3 Boot Settings Conguration .......................................... 5-32
5.7.4 Security......................................................................... 5-33
5.8 Tools menu ................................................................................. 5-35
5.8.1 ASUS EZ Flash 2.......................................................... 5-35
5.9 Exit menu.................................................................................... 5-36
Chapter6: RAIDconguration
6.1 Setting up RAID............................................................................ 6-2
6.1.1 RAID denitions .............................................................. 6-2
6.1.2 Installing hard disk drives................................................ 6-2
6.1.3 RAID controller selection ................................................ 6-3
6.1.4 Setting the RAID item in BIOS........................................ 6-3
6.2 LSISoftwareRAIDCongurationUtility .................................... 6-4
6.2.1 Creating a RAID set........................................................ 6-5
6.2.2 Adding or viewing a RAID conguration ........................6-11
6.2.3 Initializing the virtual drives........................................... 6-12
6.2.4 Rebuilding failed drives................................................. 6-16
6.2.5 Checking the drives for data consistency ..................... 6-18
6.2.6 Deleting a RAID conguration....................................... 6-21
6.2.7 Selecting the boot drive from a RAID set...................... 6-22
6.2.8 Enabling WriteCache .................................................... 6-23

vi
Contents
6.3 Intel®Matrix Storage Manager Option ROM Utility ................. 6-24
6.3.1 Creating a RAID set...................................................... 6-25
6.3.2 Creating a Recovery set ............................................... 6-26
6.3.3 Deleting a RAID set ...................................................... 6-28
6.3.4 Resetting disks to Non-RAID ........................................ 6-29
6.3.5 Recovery Volume Options ............................................ 6-30
6.3.6 Exiting the Intel®Matrix Storage Manager .................... 6-31
6.3.7 Rebuilding the RAID ..................................................... 6-31
6.3.8 Setting the Boot array in the BIOS Setup Utility............ 6-33
Chapter 7: Driver installation
7.1 RAID driver installation ............................................................... 7-2
7.1.1 Creating a RAID driver disk ............................................ 7-2
7.1.2 Installing the RAID controller driver ................................ 7-5
7.2 Intel®chipset device installation .............................................. 7-17
7.3 LAN driver installation............................................................... 7-19
7.4 VGA driver installation............................................................... 7-22
7.5 Management applications and utilities installation ................ 7-24
7.5.1 Running the support DVD............................................. 7-24
7.5.2 Drivers menu................................................................. 7-24
7.5.3 Utilities menu ................................................................ 7-25
7.5.4 Make disk menu............................................................ 7-25
7.5.5 Contact information....................................................... 7-25

vii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with manufacturer’s instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This Class B digital apparatus complies with Canadian ICES-003.
WARNING! The use of shielded cables for connection of the monitor to the
graphics card is required to assure compliance with FCC regulations. Changes
or modications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and Restriction
of Chemicals) regulatory framework, we publish the chemical substances in our
products at ASUS REACH website at http://green.asus.com/english/REACH.htm.

viii
Safety information
Electrical Safety
• Before installing or removing signal cables, ensure that the power cables for
the system unit and all attached devices are unplugged.
• To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.
• When adding or removing any additional devices to or from the system, contact
a qualied service technician or your dealer. Ensure that the power cables for
the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you service.
• If the power supply is broken, do not try to x it by yourself. Contact a qualied
service technician or your dealer.
Operation Safety
• Servicing of this product or units is to be performed by trained service
personnel only.
• Before operating the server, carefully read all the manuals included with the
server package.
• Before using the server, make sure all cables are correctly connected and the
power cables are not damaged. If any damage is detected, contact your dealer
as soon as possible.
• To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Place the server on a stable
surface.
This product is equipped with a three-wire power cable and plug for the user’s
safety. Use the power cable with a properly grounded electrical outlet to avoid
electrical shock.
Lithium-Ion Battery Warning
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
CD-ROM Drive Safety Warning
CLASS 1 LASER PRODUCT
Heavy System
CAUTION! This server system is heavy. Ask for assistance when moving or
carrying the system.

ix
About this guide
Audience
This user guide is intended for system integrators, and experienced users with at
least basic knowledge of conguring a server.
Contents
This guide contains the following parts:
1. Chapter 1: Product Introduction
This chapter describes the general features of the server, including sections
on front panel and rear panel specications.
2. Chapter 2: Hardware setup
This chapter lists the hardware setup procedures that you have to perform
when installing or removing system components.
3. Chapter 3: Rackmount installation
This chapter describes how to install the rackmount rail kit to the barebone
server
4. Chapter 4: Motherboard information
This chapter includes the motherboard layout and brief descriptions of the
jumpers and internal connectors.
5. Chapter 5: BIOS information
This chapter tells how to change system settings through the BIOS Setup
menus and describes the BIOS parameters.
6. Chapter6:RAIDconguration
This chapter provides instructions for setting up, creating and conguring
RAID sets using the available utilities.
7 Chapter 7: Driver installation
This chapter provides instructions for installing the necessary drivers for
different system components.
DO NOT throw the motherboard in municipal waste. This product has been
designed to enable proper reuse of parts and recycling. This symbol of the
crossed out wheeled bin indicates that the product (electrical and electronic
equipment) should not be placed in municipal waste. Check local regulations for
disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste.
This symbol of the crossed out wheeled bin indicates that the battery should not
be placed in municipal waste.

x
References
Refer to the following sources for additional information, and for product and
software updates.
1. ASUS Server Web-based Management (ASWM) user guide
This manual tells how to set up and use the proprietary ASUS server
management utility.
2. ASUS websites
The ASUS websites worldwide provide updated information for all ASUS
hardware and software products. Refer to the ASUS contact information.
Conventions
To make sure that you perform certain tasks properly, take note of the following
symbols used throughout this manual.
Typography
Bold text Indicates a menu or an item to select.
Italics Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than
sign means that you must press the enclosed key.
Example: <Enter> means that you must press
the Enter or Return key.
<Key1+Key2+Key3> If you must press two or more keys simultaneously,
the key names are linked with a plus sign (+).
Example: <Ctrl+Alt+D>
Command Means that you must type the command exactly
as shown, then supply the required item or value
enclosed in brackets.
Example: At the DOS prompt, type the
command line: format A:/S
DANGER/WARNING: Information to prevent injury to yourself when
trying to complete a task.
NOTE: Tips and additional information to help you complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
CAUTION: Information to prevent damage to the components when
trying to complete a task.

This chapter describes the general
features of the server, including
sections on front panel and rear panel
specications.
Chapter 1
Product introduction

Chapter 1: Product introduction1-2
*ASUS System Web-based Management
If any of the above items is damaged or missing, contact your retailer.
1.1 System package contents
Check your system package for the following items.
1.2 Serial number label
Before requesting support from the ASUS Technical Support team, you must
take note of the product’s serial number containing 14 characters such as
xxS0xxxxxxxxxx shown as the gure below. With the correct serial number of the
product, ASUS Technical Support team members can then offer a quicker and
satisfying solution to your problems.
Model Name RS100-E6/PI2
Chassis ASUS R09 1U Rackmount Chassis
Motherboard ASUS P7F-M Server Board
Component 1 x 220W Single Power Supply
2 x SATA Cables
1 x PCI Express x16 Riser Card (PCIE16-R11)
1 x Front I/O Board (FPB-R9)
1 x USB Board (USB-R9)
2 x System Fans (40mm x 28mm)
Accessories 1 x RS100-E6/PI2 User’s Guide
1 x ASUS ASWM 2.0 User’s Guide
1 x RS100-E6/PI2 Support CD (including ASWM*)
1 x Bag of Screws
1 x AC Power Cable
Optional
Items
CPU Heatsink
Riser Card: PCI 32bit/33MHz (R133-R9A)
ASUS ASMB4-iKVM Remote management card
Slim-type Optical Device
Ball Bearing Rail Kit
CA eTrust Anti-virus Software CD
xxS0xxxxxxxxxx
RS100-E6/PI2

ASUS RS100-E6/PI2 1-3
1.3 Systemspecications
The ASUS RS100-E6/PI2 is a 1U barebone server system featuring the ASUS
P7F-M server board. The server supports Intel® LGA1156 Lynneld / Clarkdale
processors, plus other latest technologies through the chipsets onboard.
Model Name RS100-E6/PI2
Processor / System Bus
1 x Socket LGA1156
Quad Core Intel® Xeon 3400 series Server Processor
Quad Core Intel®Core i7-800 series Desktop Processor
Quad Core Intel®Core i5-700 series Desktop Processor
Dual Core Clarkdale CPU design Ready
Core Logic Intel® 3420 PCH
ASUS Features Smart Fan √
ASWM2.0 √
Memory
Total Slots 4 (2 Channels)
Capacity
Maximum up to 32GB (RDIMM)
Maximum up to 16GB (UDIMM )
Desktop Processor do not support RDIMM nor
ECC UDIMM
Memory Type DDR3 1333 / 1066 Registered / Unbuffered DIMM
with ECC / Non ECC
Memory Size 1 GB, 2GB, 4GB, 8GB (RDIMM)
1 GB, 2GB, 4GB (UDIMM)
Expansion
Slots
Total PCI/PCI-X/
PCI-E Slots 1
Slot Type 1 x PCI-E 2.0 x16 slot (x16 link) (Full-Height/HL)
Storage
2 x SATA2 300MB/s ports
Intel® Matrix Storage (for Windows only)
- Supports software RAID 0 & 1
LSI® MegaRAID (for Linux / Windows)
- Supports software RAID 0 & 1
HDD Bays
I = internal
A or S = hot-
swappable
2 x Internal 3.5” SATA2 HDD Bays
Networking LAN 2 x Intel®82574L + 1 x Mgmt LAN
Graphic VGA Aspeed® AST2050 8MB
Auxiliary Storage FDD / CD / DVD 1 x Slim-type Optical Device Bay
(Options: No ODD / DVD-ROM / DVD-RW)
Onboard I/O
1 x External Serial Port
3 x RJ-45 ports (1 for ASMB4-iKVM)
4 x USB 2.0 ports (Front x 2, Rear x 2)
1 x VGA port
1 x PS/2 keyboard port
1 x PS/2 mouse port
(continued on the next page)

Chapter 1: Product introduction1-4
*Specicationsaresubjecttochangewithoutnotice.
OS Support
Windows® Server 2008 Enterprise 32 / 64-bit
Windows® Server 2003 R2 Enterprise 32 / 64-bit
RedHat® Enterprise Linux AS5.0 32 / 64-bit
SuSE® Linux Enterprise Server 10 32 / 64-bit
(Subject to change without any notice)
Anti-virus Software Optional anti-virus CD Pack
Management
Solution
Out of Band
Remote
Hardware
Optional ASMB4-iKVM for KVM-over-IP support
Software ASUS ASWM 2.0®
Net Weight Kg (CPU, DRAM &
HDD not inclu ded) 6.5 Kg
Dimension (DD x WW x HH) 380mm x 429.6mm x 43.2mm
Power Supply 220W Single Power Supply
Power Rating Input: 100-240Vac, 4-2A, 50-60Hz, Class I
Environment
Operation temperature: 10°C–35°C / Non operation
temperature: -40°C–70°C
Non operation humidity: 20%–90%
( Non-condensing)

ASUS RS100-E6/PI2 1-5
1.4 Front panel features
The barebone server displays a simple yet stylish front panel with easily accessible
features. The power and reset buttons, LED indicators, optical drive, and twp USB
ports are located on the front panel.
Refer to section 1.7.1 Front panel LEDs for the LED descriptions.
Turn off the system power and detach the power supply before removing or
replacing any system component.
1.5 Rear panel features
The rear panel includes the expansion slot and system power socket. The I/O
shield with openings for the rear panel connectors on the motherboard are also
placed in the rear panel.
AC power socket USB 2.0 ports PS/2 mouse port PS/2 keyboard port Serial port VGA port LAN port 2 LAN port 1 Expansion slot LAN port 3*
Optical drive
USB 2.0 ports
HDD Access LED
LAN2 LED
LAN1 LED
Power LED
Reset button
Power button
• The ports for the PS/2 keyboard, PS/2 mouse, USB, VGA, and Gigabit LAN
do not appear on the rear panel if motherboard is not present.
• *The port is for ASUS ASMB4-iKVM controller card only.

Chapter 1: Product introduction1-6
1.6 Internal features
The barebone server includes the basic components as shown.
The barebone server does not include a oppy disk drive. Connect a USB oppy
disk drive to any of the USB ports on the front or rear panel if you need to use a
oppy disk.
Turn off the system power and detach the power supply before removing or
replacing any system component.
*WARNING
HAZARDOUS MOVING PARTS
KEEP FINGERS AND OTHER BODY PARTS AWAY
1. PCI Express x16 Riser Card (at x16 link)
2. System Fan (x2) (9GV0412P3J051)
3. ASUS P7F-M Server Board
4. Power Supply
5. HDD Tray 2 (hidden) and Slim-type Optical
Drive (optional)
6. HDD Tray 1
6
1
2
34
5

ASUS RS100-E6/PI2 1-7
1.7 LED information
1.7.1 Front panel LEDs
LED Icon Display status Description
Power LED ON System power ON
HDD Access LED OFF
Blinking
No activity
Read/write data into the HDD
LAN LEDs
OFF
Blinking
ON
No LAN connection
LAN is transmitting or receiving data
LAN connection is present
HDD Access LED
LAN2 LED
LAN1 LED
Power LED
1.7.2 LAN (RJ-45) LEDs
ACT/LINK LED SPEED LED
Status Description Status Description
OFF No link OFF 10 Mbps connection
GREEN Linked ORANGE 100 Mbps connection
BLINKING Data activity GREEN 1 Gbps connection
SPEED LED
ACT/LINK LED

Chapter 1: Product introduction1-8

This chapter lists the hardware setup
procedures that you have to perform
when installing or removing system
components.
Chapter 2
Hardware setup

Chapter 2: Hardware setup2-2
2.1 Chassis cover
2.1.1 Removing the chassis cover
• Ensure that you unplug the power cord before removing the chassis cover.
• Take extra care when removing the chassis cover. Keep your ngers from
components inside the chassis that can cause injury, such as the CPU fan,
rear fan, and other sharp-edged parts.
• The images of the barebone server shown in this section are for reference
purposes only and may not exactly match the model you purchase.
To remove the chassis cover:
1. Use a Phillips screwdriver to remove the three screws on the chassis cover.
2. Firmly hold the cover and
slide it toward the rear
panel for about half an inch
until it is disengaged from
the chassis.
3. Lift the cover from the chassis.