Asus RX3041 User manual


RX3041&SL200Internet
ConnectionConfiguration
Guide

V1.0

Contents
Introduction....................................................................................................................1
Chapter 1: Connecting the router...................................................................................1
Chapter 2: Getting to know Internet connection type....................................................1
Chapter 3: Configuring the router..................................................................................2
3.1 Enter into router’s Web-based configuration page..........................................2
3.2 WAN Connection Type ---- Dynamic IP.........................................................3
3.3 WAN Connection Type ---- Static IP..............................................................4
3.4 WAN Connection Type ---- PPPoE.................................................................5
3.5 WAN Connection Type ---- PPTP/L2TP.........................................................6
3.6 WAN Connection Type ---- BigPond..............................................................8
Troubleshooting Tips：.................................................................................................8

1
Introduction
This document describes how to set up ASUS RX3041/SL200 for getting connection to the
Internet and provides troubleshooting tips to help you fix some simple problems.
Chapter 1: Connecting the router
The figure below illustrates a connection diagram example.
Chapter 2: Getting to know Internet connection type
The router supports following connection types: Automatic IP, Static IP, PPPOE, PPTP, L2TP,
Bigpond
9By default, the Router’s Internet Connection Type is set to Dynamic IP, which should
be kept only if your ISP (Internet Service Provider) supports DHCP (Dynamic Host
Configuration Protocol) or you are connecting through a dynamic IP address.
9If your ISP has assigned you a permanent, fixed (static) IP address for your
computer, select “Static IP”. In this type, you should have a static IP address from
your ISP, and Subnet mask, Gateway IP address are necessary.
9Most of DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to
establish Internet connections, select “PPPOE”. If you are connected to the Internet
through a DSL line, check with your ISP to see if they use PPPoE. In this type, you
should have Username and Password from your ISP.
9Point to Point Tunneling Protocol (PPTP) and Layer 2 Tunneling Protocol (L2TP).
PPTP is a service that usually applies to connections in some European countries

2
only. In this type, you should have IP address, Subnet mask, Default Gateway,
Username and Password from your ISP.
9BigPond is a service used in Australia only. If you are using a Bigpond connection,
check with your ISP for the necessary setup information.
Chapter 3: Configuring the router
3.1 Enter into router’s Web-based configuration page
a) Open browser and type router’s IP address: http://192.168.1.1 (the default address)
b) Input username and password, both of them: admin (the default value)
c) Click Cancel when show “do you like to start Quick Setup directly” (if you want to use
Quick Setup, please refer to manual or Quick Start Guide’s description).

3
3.2 WAN Connection Type ---- Dynamic IP
a) Click WAN ÎConnection, Select WAN Connection Mode as Dynamic IP Address.
b) MAC Cloning is optional as your ISP request. If it’s necessary, please enable the MAC
Cloning and fill the MAC of your PC in MAC Address field. Click Clone MAC button will
clone the MAC of current PC automatically.
c) Then click OK to save and apply the setting.
d) Click Continue back to configuration page.
e) Check if the WAN interface gets a dynamic IP address and related information. Click
Status will show WAN information.

4
3.3 WAN Connection Type ---- Static IP
a) Click WAN ÎConnection, Select WAN Connection Mode as Static IP Address.
b) Configure Static IP Address ÎInput IP Address, Subnet Mask,ISP Gateway provided
by your ISP. MAC Cloning is optional as your ISP request.
c) If your ISP provides more IP addresses, please select Yes for enabling more IP
addresses, and fill More IP Addresses, then click Add button.
d) Then click OK to save and apply the setting.
e) Click Continue back to configuration page.

5
f) Click Status will show WAN information.
3.4 WAN Connection Type ---- PPPoE
a) Click WANÎConnection,Select WAN Connection Mode as PPPoE.
b) Configure “PPPoE Account”ÎInput Username, Password provided by your ISP
c) Then click OK to save and apply the setting.
d) Click Continue back to configuration page.

6
e) Check if the WAN interface gets a dynamic IP address and related information. Click
Status will show WAN information.
3.5 WAN Connection Type ---- PPTP/L2TP
a) Click WANÎConnection, Select WAN Connection Mode as PPTP.
b) Select WAN Interface IP ÎDynamic IP
c) Select WAN Interface IP ÎStatic IP, fill IP address, Subnet Mask, Gateway that
provided by your ISP. MAC Cloning is optional as your ISP request.

7
d) Configure PPTP Account and PPTP Password provided by ISP. And Select the PPTP
Gateway type and fill the gateway info. Connection ID is optional as your ISP request.
e) Then click OK to save and apply the setting.
f) Check if the WAN interface gets a dynamic IP address and related information. Click
Status will show WAN information.
Tip: The setting steps of L2TP are similar as PPTP, please click
WANÎConnection, and select WAN Connection Mode as L2TP.

8
3.6 WAN Connection Type ---- BigPond
a) If you are using a BigPond connection, check with your ISP for the necessary setup
information.
b) Click WAN ÎConnection, Select WAN Connection Mode as Dynamic IP Address, and
enable BigPond. Fill the User Name, Password and Authentication Server in proper
field.
c) Then click OK to save and apply the setting.
d) Check if the WAN interface gets a dynamic IP address and related information. Click
Status will show WAN information.
Troubleshooting Tips：
Here are some tips for solving simple problems you may have.
Be sure to restart your network in this sequence:
1) Turn off the modem, router, and computer;
2) Turn on the modem, wait for two minutes;
3) Turn on the router and wait for one minute;
4) Turn on the computer.
Make sure the network cables are securely plugged in.
• The WAN indicator on the router lights up if the network cable to the router from the modem
is plugged in securely and the modem and router are turned on.