AT&T 9353 User manual

900 MHz Cordless Telephone/
Answering System 9353
Please also read
Part 1 — Important
Product Information
USER’S MANUAL
Part 2
2
13
HANDSET
IN USE
AT&T and the globe symbol are registered trademarks ofAT&T Corp.licensed toAdvancedAmericanTelephones.
REVISED
6/7/01
9353_book_1ATT 6/7/01 1:56 PM Page ii

© 2001AdvancedAmericanTelephones. All rights reserved.
Printed in China. Issue 1AT&T 06/01
9353_book_1ATT 6/7/01 1:56 PM Page iii

INSTALLATION ................................1
BeforeYou Install .................................1
Table/Desk Installation.........................3
Wall Installation....................................4
TELEPHONE OPERATION.................5
Make a Call...........................................5
Answer a Call.......................................5
End a Call.............................................5
Redial ...................................................5
Flash/CallWaiting.................................5
HandsetVolume ...................................5
Change Channel...................................5
Page/Handset Locator..........................6
TemporaryTone Dialing.......................7
Handset Ringer Style............................7
Ringer Off.............................................7
Headset Jack.........................................8
Operating Range ..................................8
TELEPHONE MEMORY.....................9
Store Memory Numbers.......................9
Dial Memory Numbers.........................9
Change/Replace a Stored Number.......9
Store a Pause in a Memory Number....9
Directory Label....................................9
ANSWERING SYSTEM OPERATION
At The Base .................................10
Audible Indicators..............................10
Set the Clock......................................10
About Mailboxes................................10
AboutAnnouncements ......................10
RecordYour Announcement..............11
Answering System Feature Setup.......12
Feature Summary...............................12
ListenTo,Save & Delete Messages.....13
Call Screening/Intercept....................14
Record a Memo..................................14
MessageWindow Display...................14
ANSWERING SYSTEM OPERATION
At Touch Tone Phone...................15
ConnectWith the
Answering System..........................15
Voice Menu........................................15
RemoteAccess Commands................15
BATTERIES....................................17
Charging the Handset
Battery Pack ...................................17
Replacing the Handset
Battery Pack ...................................17
IN CASE OF DIFFICULTY................18
CONTENTS
iv
9353_book_1ATT 6/7/01 1:56 PM Page iv

9353_book_1ATT 6/7/01 1:56 PM Page v

Before You Install
1 Choose a location for the base near an electrical outlet and a
telephone jack.
This phone requires a modular telephone jack and a standard electrical
outlet (110vAC) not controlled by a wall switch.
2 Install the handset battery.
1
INSTALLATION
b) Plug battery
pack connector
into handset.
Use onlyAT&T
battery 3301
(SKU# 91076).
d) Replace cover
by sliding it up
into place.
a) Remove
battery
compartment
cover by
pressing on
the indentation
and sliding
downward.
c) Place battery
pack and wires
in compartment.
9353_book_1ATT 6/7/01 1:56 PM Page 1

2
INSTALLATION
3 Attach the belt clip to the cordless handset (optional).
To attach To remove
9353_book_1ATT 6/7/01 1:56 PM Page 2

3
INSTALLATION
Use only the power cord supplied with this product. If you need a
replacement,call 1 800 222–3111.
3 Charge the handset battery.
Place the handset in the base. Charge the battery for at least 24 hours
the first time. After the first charge,the battery is typically fully
charged overnight.
4 Check for dial tone.
After the batteries are charged,pick up the handset and press P;
you should hear a dial tone.
5 Set the dial mode.
If you have touch tone service,the phone is ready to use as soon as
the batteries are charged.
If you have dial pulse (rotary) service,you’ll need to change the dial
mode. When the phone is off,press G,*,#,Mto set the
dial mode to dial pulse. To return to touch tone dialing,press
G,*,*,M.
Modular
telephone jack Standard
electrical
outlet
Table/Desk Installation
1 Connect the telephone
line cord.
2 Connect the power cord.
TheANSWER ON/OFF light
goes on,and CL flashes in the
MessageWindow.
9353_book_1ATT 6/7/01 1:56 PM Page 3

4
INSTALLATION
Wall Installation
1 Connect the telephone line cord.
2 Connect the power cord.
TheANSWER ON/OFF light goes on,and CL flashes in the Message
Window.
Use only the power cord supplied with this product. If you
need a replacement,call 1 800 222–3111.
3 Mount the base on the wall.
4 Follow Steps 3–5 in “Table/Desk Installation.”
a) Align holes
on base with
mounting
studs on wall
jack.
b) Place power
cord as shown.
c) Pull base
down on
mounting
studs until it
locks into
place.
9353_book_1ATT 6/7/01 1:56 PM Page 4

5
TELEPHONE OPERATION
Temporary Tone
Handset Volume
Adjust volume of
what you hear
through the handset.
Answer a Call
Lift handset from base
— OR —
Press any key.
Make a Call
Press and wait for light
to go on steadily.
Flash/Call Waiting
Access special
telephone company
subscriber services.
Change Channel
Press to switch to a
clearer channel.
Redial
Press P,then
press r
to call the last
number dialed
(up to 16 digits).
End a Call
Place handset in base
— OR —
Press O.
Exit programming
without saving.
Cancel a page.
On steadily:
Handset in use
Flashing:
Line ringing
Blinking:
Programming mode
Flashing slowly:
Battery low
9353_book_1ATT 6/7/01 1:56 PM Page 5

6
TELEPHONE OPERATION
Page/Handset Locator
Press once to page the handset for up
to one minute;press twice to cancel.
Indicates
handset
is in base
Flashing: a call is coming in
On steadily: the handset is in use
2
13
9353_book_1ATT 6/7/01 1:56 PM Page 6