AT&T E1113B User manual

TONE
MUTE
DELETE
REDIAL INT
PAUSE
FLASH
CLEAR
Quick start guide
2.4 GHz Cordless
Telephone/Answering
System E2913B/
E1113B
with caller ID/call waiting

Installation and setup
After installing the battery, you may be able to make and receive short calls.
For best performance, place the handsets in the telephone base or the charg-
er and charge for 16 hours before use.
You can keep the battery charged by returning the handsets to the telephone
base or the charger after use. When the battery is fully depleted, a recharge
takes about 12 hours. The average talk time on a fully charged battery is
about eight hours, and the standby time is approximately five days. Actual
battery life depends on usage conditions and age of battery.
1. Insert the plug as
indicated. Be sure
to securely insert
the plug, making
sure matches the
color-coded label
inside the battery
compartment.
Caution: Use only the supplied
rechargeable battery or replacement
battery (model 27910, part number
89-0099-00-00) or equivalent. To
order a replacement battery, visit our
website at www.telephones.att.com
or call 1 [phone]; in Canada,
call 1 [phone].
3. Slide the bat-
tery compart-
ment cover up
until it clicks.
2. Place the
battery pack
and wires
inside the
compartment.
NOTE: Under normal condi-
tions, the battery should last around
one year. This may vary depending
on usage.
Choose a central location close to a telephone jack and a power outlet not
connected to a wall switch. The telephone base can be placed on a flat sur-
face or mounted on a standard wall plate. For optimum range and better
reception, place the telephone base in a high and open location.
Avoid placing the telephone base too close to:
• Communication devices such as: personal computers, computer routers,
television sets, VCRs, wireless routers (wireless broadband, wi-fi, or 802.11)
or other cordless telephones.
• Excessive heat sources.
• Noise sources such as a window with traffic outside, motors, microwave
ovens, refrigerators, or fluorescent lighting.
• Excessive dust sources such as a workshop or garage.
• Excessive moisture.
• Extremely low temperatures.
• Mechanical vibration or shock such as on top of the washing machine or
work bench.

8. You may be able to
make and receive short
calls. For best perform-
ance, place the hand-
set in the telephone
base or charger to
charge for at lease 16
hours before first use.
6. Plug the small end
of the smaller power
adapter into the jack
on the underside of
the charger, then route
the cord through the
slot as shown.
7. Plug the large end
of the smaller power
adapter into an electri-
cal outlet not control-
led by a wall switch.
Installation and setup
Telephone line cord
DSL filter
(Optional for DSL users,
see number four in the
note section, below.)
NOTES:
1. Use only the power cord supplied with this product. To
order a replacement power cord, visit our website
at www.telephones.att.com, or call 1 [phone]; in
Canada, call 1 [phone].
2. Be sure to use an electrical outlet not controlled by a wall
switch.
3. This power unit is intended to be correctly oriented in
a vertical or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
4. If you receive high speed internet through your telephone
line (commonly referred to as DSL), and you are experienc-
ing interference during telephone conversations and/or
your caller ID features are not functioning properly, install
a DSL filter to the telephone line between the telephone
base and the telephone wall jack. Contact your DSL serv-
ice provider for a DSL filter.
5. Plug the other end
of the telephone line
cord into a telephone
jack.
4. Plug the large
end of the larger
power adapter into
an electrical outlet
not controlled by a
wall switch.
3. Route cords
through slots.
1. Plug one end of the telephone line cord
into the telephone jack at the bottom of
the telephone base.
2. Plug the small end of the power adapter into
the power jack at the bottom of the telephone
base.
TONE
MUTE
DELETE
REDIAL INT
PAUSE
FLASH
CLEAR

OFF/CLEAR
During a call, press to hang up.
While using menus, press to cancel
an operation, back up to the previous
menu, or exit the menu display.
While predialing, press to delete
digits.
Quick reference guide
TONE
MUTE
DELETE
REDIAL
PAUSE
MUTE/DELETE
While on a call, press to
mute microphone. While
reviewing the call log, press
to delete an individual entry,
or press and hold to clear
the caller ID log. While
entering or editing a name
or number, press to delete a
character.
CID/-VOLUME
Press to scroll down while in
menus. Press to display caller
ID information. While entering
names or numbers, press to
move the cursor to the left.
Press to decrease the listen-
ing volume while on a call.
SPEAKER
Press to activate handset
speakerphone. Press again to
resume normal handset use.
DIR /VOLUME+
Press to scroll up while in menus.
Press to display directory entries.
While entering names or numbers,
press to move the cursor to the
right. Press to increase the listen-
ing volume while on a call.
PHONE/FLASH
Press to make or answer a
call. During a call, press to
receive an incoming call if
call waiting is activated.
INT
Press to initiate an intercom con-
versation between handsets. Press
to transfer a call.
Cordless handset
Feature menu
Menu
Feature menu
DIRECTORY
CALL LOG
SETTINGS
SOUNDS
DISPLAY
RINGER VOLUME
Using menus
Press CID/-VOLUME or
DIR /VOLUME+ to scroll
through menu items.
Press MENU/SELECT to select or
modify a highlighted item.
Press OFF/CLEAR to cancel an
operation, back up to the previous
menu, or exit the menu display.
MENU/SELECT
Press to display the menu. Once in
the menu, press to select an item
or save an entry or setting.
TONE
MUTE
DELETE
REDIAL
PAUSE
Shows a highlighted item
REDIAL/PAUSE
Press to view redial memory. While
entering numbers, press and hold
to insert a dialing pause.
DIRECTORY
NOTE: For more information, please refer to the user's manual.

Quick reference guide
Telephone base
CHARGE/IN USE
Flashes when another telephone on
the same line or one of the handsets
is in use.
Flashes when the answering system is
answering an incoming call.
Flashes while an incoming call is ringing.
On steady when the handset is
properly positioned to charge in the
telephone base.
HANDSET LOCATOR
Press to make handsets
beep.


Press to review or change
answering system options.
Press to delete message cur-
rently playing; press and hold
to delete all old messages.
Press to review or record
announcement; press
again to quit.
Press to record a memo
or after pressing ANNC
to record an outgoing
announcement.
Press to turn answering
system on or off.
Press to repeat mes-
sage; press twice to
play previous message.
Press to start or stop
message playback.
Press to adjust playback
volume.
Press to skip message.
/SKIP
VOLUME
ANSWER ON
RECORD
X/DELETE
PLAY/STOP
ANNC
CLOCK
/REPEAT
Press to review or set
clock.
SETUP
Number of messages (or
during playback, message
number currently playing).
MESSAGE COUNTER
NOTE: For more information, please refer to the user's manual.

Copyright © 2006 Advanced American Telephones. All rights reserved.
AT&T and the Globe symbol are trademarks of AT&T Knowledge Ventures,
licensed to Advanced American Telephones. Printed in China. Issue 1 AT&T 12/06.
96-006309-010-100
www.telephones.att.com