Atlantic Technology ICTS-6.1 User manual

Installation Instructions
Thank you for purchasing Atlantic Technology speaker products.These
high quality 2-way speakers solve a myriad of surround sound and
distributed audio installation problems. We work very hard to ensure
that all of our speakers consistently deliver exceptional performance
and value.
We hope you enjoy them to their fullest. Please take a moment to read
these instructions so you can get the most from your speakers.
Mounting Specifications
These speakers are intended for mounting in a ceiling,in material rang-
ing from ½ inch to 1 inch thick.They require at least 4 5
⁄8inches of depth
as measured from the front surface of the ceiling .The cutout opening
for the ICTS-6.1 is 7 3
⁄8inches in diameter (3 11 ⁄16 inches radius). These
speakers will work equally as well in a wall as in a ceiling; however note
that they require more mounting depth than is normally available in a
2x4 studded wall.
Mounting Locations
Generally, it’s best to keep the speaker at least 24 inches away from any
nearby wall boundaries (wall/corner), since placing any speaker in
close proximity to other boundary surfaces will artificially reinforce
the upper bass/lower midrange sound, adversely “coloring” the sound
that the speaker produces.
The ICTS-6.1’s 1-inch dome tweeter is mounted in a pivoting housing,
so it to can be directed precisely towards the listening area for best
sound.
Model ICTS-6.1
When painting the grille...
™
ICTS-6.1-IP
Ceiling Speakers
Specifications
Dimensions 8 9⁄16” (220 mm)
Cutout Dimensions 7 3⁄8” (188 mm)
Mounting Depth (from front surface of ceiling) 4 5⁄8” (118 mm)
New Construction Bracket (optional) IC-NC-6.1
In-ceiling Back Box (optional) IC-BOX-6/8
Frequency Response 59-20kHz +/- 3dB
Sensitivity 88dB 1Watt/1 Meter
Recommended Amplifier Power 10-100 Watts RMS
Impedance 6 ohms
Woofer 6 ½” Polypropylene cone
Tweeter 1” Pivoting soft dome
Net Weight 4.6 Lbs (2.1 kg)
1. Remove Scrim
2. Paint Grille
3. Reapply Scrim

For Connection to an IP-type system,like NetStreams®:
Unscrew the 4 setscrews
on top of the built-in
Phoenix connector and
pull the wires away from
the connector. See Figure
3 (You may tie or clip the
wires that used to connect
here.)
Connect the wires from
the NetStreams amplifier
to the ICTS-6.1's Phoe-
nix connector and screw
down tightly.Consult your
NetStreams manual for
wiring details.
Atlantic Technology
343 Vanderbilt Avenue Norwood, MA 02062
[phone] www.atlantictechnology.com
015-1061
New Construction and Retrofit Installations
Note: A new construction rough-in kit and back box kit are optionally
available from Atlantic Technology. Please refer to the instructions included
in those kits for their use. If the rough in kit has been used please go directly
to Step 2 below.
Mounting Hole Specifications:
ICTS-6.1: Diameter = 7 3⁄8in., 188mm; Depth = 4 5⁄8 in., 118mm
1Cut an appropriately sized opening in the ceiling material.Be sure that the
ceiling material can support the weight of the speaker.Also be sure that
the sides of the opening are at least 1 ½ inches away from any beams or
studs within the cavity.If it is not,the rotating clamps will be restricted
in their movement and may not clamp properly.
No less than 1 ½”
Joist
or Stud Joist
or Stud
Figure 1
2Be sure that all foreign material in the ceiling is kept out of the speaker
assembly,particularly the back of the woofer cone.There is a cloth shield
on the rear of the woofer, but please use care anyway.
3For conventional Connection to an audio amplifier/receiver:
Attach the speaker wires that have been already run through the ceiling
to the speaker terminals. Simply remove ½ inch of insulation from the
end of each input wire. Push down on the terminal connector and an
opening will appear in the connector that is capable of holding up to 14
gauge wire.Insert the bare wire into the opening and release the terminal.
Be sure to observe correct polarity, connecting the positive (+) leads to
the red terminals and the negative (-) leads to the black terminals.Also
be sure that no stray strands of wire touch across any terminals. See
Figure 2.
Figure 2
Grille
Ceiling
Figure 3
4Mount the speaker in the ceiling.
Tighten the mounting screws one at a time. As you tighten the screws,
the clamps on the back of the assembly will turn and lower, grabbing
the back of the ceiling and sandwiching the ceiling between themselves
and the frame’s circular trim ring.
5Snug all four mounting screws in this manner. Be careful not to over-
tighten them.
IMPORTANT: If you are using an electric screwdriver, make sure it is
set to the“low torque”position.
6You may now install the grille into the frame by gently pushing it into
the recess.
Figure 4