Atlas Copco LZB33-LB-AR009-11 Instruction sheet

LZB33-LB-AR009-11 ATEX
Printed Matter No. 9836 6721 01 Air Motors
Publication Date 2019-10-17
Valid from Serial No. B5780001
Valid to Serial No. B1759999 Product Instructions
LZB33-LB-AR009-11 8411034047
Free speed: 800 r/min
Lubrication free
Ex II 2GD c T6 IIC T85 ᵒC
WARNING
Read all safety warnings and instructions
Failure to follow the safety warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference

2© Atlas Copco Industrial Technique AB - 9836 6721 01
Table of Contents
Product information................................................................................................4
General information ..........................................................................................4
Safety signal words ...............................................................................4
Warranty ................................................................................................4
ServAid ..................................................................................................4
Website..................................................................................................5
Safety Data Sheets MSDS/SDS............................................................5
Warning .................................................................................................5
Country of origin ....................................................................................5
Dimensional drawings ...........................................................................5
Overview...........................................................................................................5
Technical data .......................................................................................5
Service overview...............................................................................................6
Service recommendations .....................................................................6
ATEX certification information ..........................................................................6
Temperatures ........................................................................................6
Ex Classification ....................................................................................7
ATEX code definition .............................................................................7
Explosion prevention guidelines ............................................................7
Installation ...............................................................................................................9
Installation requirements...................................................................................9
Air quality...............................................................................................9
Air lubrication guide ...............................................................................9
Compressed air connection...................................................................9
Shaft load diagram ..............................................................................10
Shaft load ............................................................................................10
Installation instructions ...................................................................................10
Installation diagram .............................................................................10
Connecting the air supply ....................................................................10
Operation ...............................................................................................................12
Ergonomic guidelines .....................................................................................12
Operating instructions.....................................................................................12
Hot Spots.............................................................................................12
Service ...................................................................................................................14
Maintenance instructions ................................................................................14
Service recommendations ...................................................................14
Overhaul ..............................................................................................14
Maintenance ........................................................................................14
Lubrication instructions ...................................................................................15
Rust protection and cleaning ...............................................................15
Grease guide .......................................................................................15
Lubrication ...........................................................................................16

3
© Atlas Copco Industrial Technique AB - 9836 6721 01
Recycling ...............................................................................................................17
Recycling instruction.......................................................................................17

Product information EN LZB33-LB-AR009-11 ATEX
4© Atlas Copco Industrial Technique AB - 9836 6721 01
Product information
General information
WARNING Risk of Property Damage or Severe Injury
Ensure that you read, understand and follow all instructions before operating the tool. Failure to follow
all the instructions may result in electric shock, fire, property damage and/or severe bodily injury.
►Read all Safety Information delivered together with the different parts of the system.
►Read all Product Instructions for installation, operation and maintenance of the different parts of
the system.
►Read all locally legislated safety regulations regarding the system and parts thereof.
►Save all Safety Information and instructions for future reference.
Safety signal words
The safety signal words Danger, Warning, Caution, and Notice have the following meanings:
DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or se-
rious injury.
WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if
not avoided, could result in minor or moderate injury.
NOTICE NOTICE is used to address practices not related to personal injury.
Warranty
■Product warranty will expire 12 months after the product is first taken into use, but will in any case ex-
pire at the latest 13 months after delivery.
■Normal wear and tear on parts is not included within the warranty.
■Normal wear and tear is that which requires a part change or other adjustment/overhaul during
standard tools maintenance typical for that period (expressed in time, operation hours or other-
wise).
■The product warranty relies on the correct use, maintenance, and repair of the tool and its component
parts.
■Damage to parts that occurs as a result of inadequate maintenance or performed by parties other
than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the
warranty.
■To avoid damage or destruction of tool parts, service the tool according to the recommended mainte-
nance schedules and follow the correct instructions.
■Warranty repairs are only performed in Atlas Copco workshops or by Certified Service Partners.
Atlas Copco offers extended warranty and state of the art preventive maintenance through its ToolCover
contracts. For further information contact your local Service representative.
For electrical motors:
■Warranty will only apply when the electric motor has not been opened.
ServAid
ServAid is a portal that contains technical information for all hardware and software products such as:
- Safety Information including declarations, standards and directives
- Technical data

LZB33-LB-AR009-11 ATEX EN Product information
© Atlas Copco Industrial Technique AB - 9836 6721 01 5
- Installation, Operation and Service Instructions
- Spare parts lists
- Accessories
ServAid is continuously updated and is available at:
https://servaid.atlascopco.com
For further information contact your local Atlas Copco representative.
Website
Log in to Atlas Copco: www.atlascopco.com.
You can find information concerning our products, accessories, spare parts and published matters on our
website.
Safety Data Sheets MSDS/SDS
The safety data sheets describes chemical products sold by Atlas Copco.
For more information, consult the website:
www.atlascopco.com/sds
Warning
WARNING Polymer hazard
The vanes in this product contain PTFE (a synthetic fluoropolymer). Due to wear, there might be
PTFE particles inside the product. Heated PTFE can produce fumes which may cause polymer fume
fever with flu-like symptoms, especially when smoking contaminated tobacco.
Health and Safety recommendations for PTFE must be followed when handling vanes and other com-
ponents:
►Do not smoke when servicing this product
►PTFE-particles must not come in contact with open fire, glow or heat
►Motor components must be washed with cleaning fluid and not blown clear with an air line
►Wash your hands before starting any other activity
Country of origin
Please refer to the information on the product label.
Dimensional drawings
For information about the dimensions of a product, see the Dimensional drawings archive:
http://webbox.atlascopco.com/webbox/dimdrw
Overview
Technical data
Ordering No 8411034047
Model LZB33-LB-AR009-11
Air consumption at free speed l/s
Air consumption at free speed cfm
Air consumption at max output 7.9 l/s
Air consumption at max output 16.8 cfm

Product information EN LZB33-LB-AR009-11 ATEX
6© Atlas Copco Industrial Technique AB - 9836 6721 01
Braking torque 8.9 Nm
Braking torque 6.6 ft lb
Built in brake Yes
External parts material Hardened steel/Aluminium
Free speed 800 r/min
Max output 0.25 kW
Max output 0.34 hp
Min starting torque 7 Nm
Min starting torque 5.2 ft lb
Ratio
Rotation direction Reversible
Shaft loading code c
Shaft type Keyed
Speed at max output 430 r/min
Stall torque 10.8 Nm
Stall torque 8 ft lb
Torque at max output 5.4 Nm
Torque at max output 4 ft lb
Vane type Lubrication free
Weight 1.63 kg
Weight 3.59 lb
Inlet hose 10 mm
Inlet hose 3/8'' in
Outlet hose 10 mm
Outlet hose 3/8'' in
Service overview
Service recommendations
Preventive maintenance is recommended at regular intervals. See the detailed information on preventive
maintenance. If the product is not working properly, take it out of service and inspect it.
If no detailed information about preventive maintenance is included, follow these general guidelines:
■Clean appropriate parts accurately
■Replace any defective or worn parts
ATEX certification information
Temperatures
■The maximum surrounding temperature for which the certification is valid is 40°C.
■40°C is also the maximum allowed temperature of the compressed air when it enters the product.
■If the product is installed in an equipment, the entire equipment has to correspond to the guidelines
2014/34/EU.
■Make sure that the compressed air fulfil our quality demands (quality classes 2.4.3. and 3.4.4 respec-
tively 3.5.4 acc. to ISO/DIS 8573-1).
■Do not exceed maximum pressure of 6.3 bar, or as stated on the product nameplate. Exceeding the
operating pressure can increase the surface temperature due to higher rotating speed and the prod-
uct can become an ignition source.

LZB33-LB-AR009-11 ATEX EN Product information
© Atlas Copco Industrial Technique AB - 9836 6721 01 7
Ex Classification
If the product is part of an assembly where the components have different Ex classification, the compo-
nent with the lowest level of safety defines the Ex classification of the complete assembly.
ATEX code definition
The ATEX code is:
Ex II 2GD c T6 IIC T85 ᵒC
Description Value Definition
Equipment group II Surface Industry
Equipment category
Group II
2High level of protection
■zone 1 (gas)
■zone 2 (gas)
■zone 21 (dust)
■zone 22 (dust)
Atmosphere GAtmosphere containing Gas, Va-
pors or Mist
DAtmosphere containing Dust
Safety design cConstructional safety
Gas group IIC Hydrogene/ Acetylene
IIB Ethylene
Max surface temperature in Gas at-
mosphere
T1 = 450°C
T2 = 300°C
T3 = 200°C
T4 = 135°C
T5 = 100°C
T6 = 85°C
Max surface temperature in Dust at-
mosphere
Example temperatures:
T85°C
T110°C
T120°C
T125°C
T240°C
Explosion prevention guidelines
Cleanliness
■Make sure the product is kept clean from dust and dirt to prevent increased bearing and surface tem-
perature.
■If using a silencer: Make sure a silencer with a filtering effect at the air outlet is installed to prevent
any friction-heated particles entering into the surrounding atmosphere.
Usage
■Make sure the product is earthed to the equipotential bonding system of the workshop, for example
through accessories such as hoses and air-pressure connections.

Product information EN LZB33-LB-AR009-11 ATEX
8© Atlas Copco Industrial Technique AB - 9836 6721 01
■It is the responsibility of the user to make sure that the product and all possible accessories, such as
wrenches and air connections, conform to the national safety regulations for equipment used in po-
tentially explosive areas.

LZB33-LB-AR009-11 ATEX EN Installation
© Atlas Copco Industrial Technique AB - 9836 6721 01 9
Installation
Installation requirements
Air quality
■For optimum performance and maximum product life we recommend the use of compressed air with
a maximum dew point of +10°C (50°F). We also recommend to install an Atlas Copco refrigeration
type air dryer.
■Use a separate air filter which removes solid particles larger than 30 microns and more than 90% of
liquid water. Install the filter as close as possible to the product and prior to any other air preparation
units to avoid pressure drop.
For impulse/impact tools make sure to use lubricators adjusted for these tools. Regular lubricators
will add too much oil and therefore decrease the tool performance due to too much oil in the mo-
tor.
Make sure that the hose and couplings are clean and free from dust before connecting to the tool.
Both lubricated and lubrication free products will benefit from a small quantity of oil supplied from a lu-
bricator.
Air lubrication guide
Brand Air lubrication
Atlas Copco Optimizer (1 liter) 9090 0000 04
Q8 Chopin 46
Shell Shell Air Tool Oil S2 A 320
Compressed air connection
WARNING Compressed air can cause serious injury
►Always shut off the air supply, drain hose of air pressure and disconnect the tool from air supply;
when not in use, before making any adjustments to the product - for example changing acces-
sories, or when making repairs.
WARNING Whipping hoses can cause serious injury
►Always make sure that there are no damaged or loose hoses or fittings.
WARNING Compressed Air
High air pressure can cause severe damage and bodily injury.
►Do not exceed maximum air pressure.
►Make sure that there are no damaged or loose hoses or fittings.
For correct air pressure and hose size, see section Technical data.
Make sure that the hose and couplings are clean and free from dust before connecting to the tool.

Installation EN LZB33-LB-AR009-11 ATEX
10 © Atlas Copco Industrial Technique AB - 9836 6721 01
Shaft load diagram
Shaft load
■Make sure that the maximum shaft load is not exceeded, in order to prevent an excessive increase of
the bearing temperature.
Installation instructions
Installation diagram
Reversible motor
Connecting the air supply
When the compressed air supply is connected to the inlet, the direction of rotation will be as shown in the
figure below. If the exhaust air is to be piped away, a hose should be connected to the exhaust outlet.
The compressed air supply should be connected to the corresponding inlet for desired rotation direction,
see figure below. The inlet that is not in use, functions as an additional outlet and must not be plugged.

LZB33-LB-AR009-11 ATEX EN Installation
© Atlas Copco Industrial Technique AB - 9836 6721 01 11

Operation EN LZB33-LB-AR009-11 ATEX
12 © Atlas Copco Industrial Technique AB - 9836 6721 01
Operation
Ergonomic guidelines
Consider your workstation as you read through this list of general ergonomic guidelines and see if you can
identify areas for improvement in posture, component placement, or work environment.
■Take frequent breaks and change work positions frequently.
■Adapt the work area to your needs and the work task.
■Adjust for convenient reach range by determining where parts or tools should be located to avoid
static load.
■Use workstation equipment such as tables and chairs appropriate for the work task.
■Avoid work positions above shoulder level or with static holding during assembly operations.
■When working above shoulder level, reduce the load on the static muscles by reducing the weight
of the load. You can also reduce the load on the static muscles by holding the load close to the
body.
■Make sure to take frequent breaks.
■Avoid extreme arm or wrist postures, particularly for operations requiring a degree of force.
■Adjust for convenient field of vision by minimizing movement of the eyes and head during the work
task.
■Use the appropriate lighting for the work task.
■Use ear protection equipment in noisy environments.
■Use dust extraction system or mouth protection mask in dusty environments.
Operating instructions
Hot Spots
The following hotspots on the motor (as seen in the figure) can reach high temperatures during operation:
■Seal ring at the output shaft
■Joint between front part and gear ring
■Key grip
Straight models

LZB33-LB-AR009-11 ATEX EN Operation
© Atlas Copco Industrial Technique AB - 9836 6721 01 13
Angled models
The highest temperatures occur when the motor is running at full pressure without load. With increasing
torque, the air motor reduces the rotational speed and the temperature.

Service EN LZB33-LB-AR009-11 ATEX
14 © Atlas Copco Industrial Technique AB - 9836 6721 01
Service
Maintenance instructions
Service recommendations
Preventive maintenance is recommended at regular intervals. See the detailed information on preventive
maintenance. If the product is not working properly, take it out of service and inspect it.
If no detailed information about preventive maintenance is included, follow these general guidelines:
■Clean appropriate parts accurately
■Replace any defective or worn parts
Overhaul
To achieve the best engine service life under normal operating conditions, regular overhaul and cleaning
should be carried out every 12 months or after every 1000 hours (lubrication free models) or 2000 hours
(standard models) of operation, whichever is the sooner. Overhaul should be carried out more frequently
under more rigorous operating conditions.
Clean the engine thoroughly.
Fit the engine and check that it rotates freely. Pour two drops of oil into the air intake and idle the en-
gine for 5-10 seconds.
If the compressed air is very dry, the idle speed for lubricant-free engines may decrease slightly after
fairly long periods of operation. This decrease may amount to 10-15%.
Maintenance
■Maintenance and repairs of this ATEX product must be carried out exclusively by authorised person-
nel, after which a no-load test and temperature measurements of hotspots (as seen in the figure)
must be carried out and recorded in a report.
After a 5 min no-load test the surface temperature must not exceed the sum of 45°C + surrounding
temperature, where the surrounding temperature can vary between 0 – 40°C.

LZB33-LB-AR009-11 ATEX EN Service
© Atlas Copco Industrial Technique AB - 9836 6721 01 15
Lubrication instructions
Rust protection and cleaning
Water in the compressed air can cause rust. To prevent rust we strongly recommend to install an air dryer.
Water and particles can cause sticking of vanes and valves. This can be prevented by installing an air fil-
ter close to the product to avoid pressure drop.
Before longer standstills always protect your tool by adding a few drops of oil into the air inlet. Run the tool
for 5–10 seconds and absorb any access oil at the air outlet in a cloth.
Grease guide
Brand General purpose, Bearings and Gears
Klüber Lub. Klübersynth UH 1 14-151
Klüber Lub. Klübersynth UH 1 64-62
Food grade approved
Brand General purpose, Bearings and Gears *
BP Energrease LS-EP2
Esso Beacon EP2
Q8 Rembrandt EP2
Mobil Mobilegrease XHP 222 NLG 2
Texaco Multifak EP2
Molykote BR2 Plus
Klüber Lub. Klübersynth UH 1 14-151
Castrol OBEEn UF 1
Non food grade approved
* Not for angle gears

Service EN LZB33-LB-AR009-11 ATEX
16 © Atlas Copco Industrial Technique AB - 9836 6721 01
Brand Angle gears
Molykote Longterm 2 Plus
Non food grade approved
Brand Seal ring
Shell Shell Gadus S2 V100 2
Shell Shell Gadus S2 V220 2
Non food grade approved
Lubrication
Planetary gears, ball- and needle bearings and seal ring should be lubricated with grease in conjunction
with the regular overhaul of the motor.
Always use lubricants of good quality. The oils and greases mentioned in the chart are examples of lubri-
cants which are recommended.

LZB33-LB-AR009-11 ATEX EN Recycling
© Atlas Copco Industrial Technique AB - 9836 6721 01 17
Recycling
Recycling instruction
When a product has served its purpose it has to be recycled properly. Dismantle the product and recycle
the components in accordance with local legislation.

Original instructions
Atlas Copco Industrial
Technique AB
SE-10523 STOCKHOLM
Sweden
Telephone: [phone]
Telefax: [phone]
www.atlascopco.com
© Copyright 2019, Atlas Copco Industrial Technique AB. All rights reserved. Any
unauthorized use or copying of the contents or part thereof is prohibited. This
applies in particular to trademarks, model denominations, part numbers and
drawings. Use only authorized parts. Any damage or malfunction caused by the
use of unauthorized parts is not covered by Warranty or Product Liability.
Out of respect to wildlife and nature, our technical literature is printed on
environmentally friendly paper.