Atlas PX-16A User manual

Revised 01/15/2020
Read this entire manual before operation begins.
Record below the following information which is located on the serial number
data plate.
Serial No.
Model No.
Date of Installation

Contents
PX-16A Specifications . . . . . . . . . 4
Installation Requirement . . . . . . . 5
Installation Steps . . . . . . . . . . . 7
Test Run . . . . . . . . . . . . . . . 29
Operation Instructions. . . . . . . . . 31
Maintenance Schedule. . . . . . . . . 32
Trouble Shooting . . . . . . . . . . . 34
Exploded View . . . . . . . . . . . . 35
PX-16A Parts List . . . . . . . . . . . 39
Warranty . . . . . . . . . . . . . . . 48

PX-16A Specifications 4
PX-16A
PX-16A Specifications
• Electric-air control system, safety self-lock mechanism
• 2-Dual synchronous cylinders are applied to assure the lifting level on both
platforms
• Skid proof diamond runway
• Integrated rear slip-plates
• Heavy duty design, fit for a wide range of vehicle car to van and light truck
• Includes Turntables
• Optional Jack (with hand pump/air-operated hydraulic pump)
• • Optional Turnplate (1 manual or air rolling jack; 2 turnplate)
Fig. 1
Lifting
Capacity
Lifting
Height
Min.
Height
Lifting
Time
Overall
Length
(Inc.Ramps)
Overall
Width
Runway
Width
Distance
Between
Runway
Gross
Weight Motor
7.3T
16000 lbs
1870mm
73 5/8”
330mm
13” 82 sec. 6964mm 274 1/8”
2390mm
94”
625mm
24 5/8”
1055mm
41 1/2”
2784Kg
6132 lbs 2.0HP

Installation Requirement 5
PX-16A
Installation Requirement
Tools Required
Rotary Hammer Drill (Φ19, Φ10, Φ4,) Carpenter’s Chalk
Hammer Screw Drivers
4 Foot Level Tape Measure (25ft)
Crescent Wrench (12”) Pliers
Ratchet & Socket (28mm) Grease gun
Wrench set (mm)
(8#, 14#, 15#, 17#, 19#)
Vise Grips
Fig. 2

Installation Requirement 6
PX-16A
Concrete Specifications
Specifications of concrete must be adhered to the specification as
following. Failure to do so may result in lift and/or vehicle falling.
1. Concrete must be 4 inches thick minimum and without reinforcing steel
bars, and must be dried totally before the installation.
2. Concrete must be in good condition and must be of test strength 3,000psi
(210kg/cm²) minimum.
3. Floors must be level and no cracks.
Power Supply
The electrical source must be 3Kw minimum. The source cable size must be
2.5mm² and in good condition of contacting with floor.

Installation Steps 7
PX-16A
Installation Steps
A. Location of Installation
Check and insure the installation location (concrete, layout, space size etc.) is
suitable for lift installation.
1. For Standard Installation: On surface installation
1.1 On surface installation foundation (See Fig. 3).
Fig. 3

Installation Steps 8
PX-16A
1.2 Illustration for on surface installation (See Fig. 4).
Fig. 4

Installation Steps 9
PX-16A
2. For Optional Installation: Flush mount installation
2.1 Flush mount installation foundation (Fig. 5).
The concrete thickness at the bottom must be at least 4 inches. The bearing
pressure must be over 460lbs/cm. All pipe must be PVC with 4 inch diameter.
Fig. 5

Installation Steps 10
PX-16A
2.2 Illustration for flush mount installation (Fig. 6).
Fig. 6