Atleisure FRN-105260 Installation guide

5 PC Wicker Dining Set
Assembly & Care Instructions
IMPORTANT : RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
Item: 1896723 / 1896724
Model: FRN- 105260
ATLeisure, LLC
Toll Free: 1-855-880-7205 (English is offered)
8am - 5pm, Monday through Friday, Eastern Standard Time
Email: customerser[email protected] or visit our website at www.atleisure.com
DO NOT RETURN TO STORE
For indoor/outdoor domestic use only. Not for commercial use.
Designed in USA
Made in China
For assistance with assembly, parts, or customer service, please contact:

2
Contents
Package Contents ...........................2-3
Assembly..................................4-8
Care and Maintenance.........................8
Warnings and Cautions ........................9
Warranty ...................................9
Before assembling make sure all parts are present. If any part is missing or
damaged, do not attempt to assemble the product. Contact our customer service
representative for assembly assistance or questions toll free at 1-855-880-7205.
Package Contents
CAUTION: Do not use sharp tools or equipment such as a
knife or scissors when removing the protective material, as it
may damage the product.
Table Parts
Item Part Quantity
Table Top
A1
Table Leg
B4
(C) Bolt
(D) Washer
(E) Bolt Cap
(F) Hex Key
1 Hardware Pack Includes:
12 Bolts
12 Washers
12 Bolt Caps
1 Hex Key
Bolt Washer
Bolt Cap Hex Key
Bolt

3
Before assembling make sure all parts are present. If any part is missing or
damaged, do not attempt to assemble the product. Contact our customer service
representative for assembly assistance or questions toll free at 1-855-880-7205.
Package Contents
CAUTION: Do not use sharp tools or equipment such as a
knife or scissors when removing the protective material, as it
may damage the product.
Chair Parts
Item Part Quantity
Chair Seat A4
Left Chair Leg
B4
Right Chair Leg
C4
Chair Back
D4
Support Bar E4
(F) Short Bolt
(G) Long Bolt
(H) Washer
(I) Bolt Cap
(J) Hex Key
1 Hardware Pack Includes:
40 Short Bolts (M6x20)
16 Long Bolts (M6x30)
56 Bolt Caps
1 Hex Key
Bolt
Washer
Hex Key
Bolt Cap
Long Bolt

4
Table Assembly
A
BE
C
D
Step 1: Place tabletop (A) upside down on a soft, flat sur-
face. Align one table leg (B) with corresponding tabletop
hole. Place washer (D) over the hole and insert bolt (C). Use
hex key (F) to tighten bolt, being careful not to overtighten.
Repeat steps for remaining table legs
Step 2: Turn table over and place on flat surface. Once level,
tighten all bolts. Attach all bolt caps (E) onto the bolts. Table
is ready for use.

5
Chair Assembly
Step 1: Place contents on soft, flat surface. Attach the chair
seat (A) to the left chair leg (B) with two washers (H) and two
long bolts (G). Use hex key (J) to tighten bolts, being careful
not to overtighten.
Step 2: Attach the chair back (D) to the left chair leg (B) with a
washer (H) and a short bolt (F). Use hex key (J) to tighten bolt,
being careful not to overtighten.

6
Chair Assembly (continued)
Step 3: Attach the right chair leg (C) to the chair seat (A)
with two washers (H) and two long bolts (G). Use hex key
(J) to tighten bolts, being careful not to overtighten.
Step 4: Attach the right chair leg (C) to the chair back (D)
with a washer (H) and a short bolt (F). Use hex key (J) to
tighten bolts, being careful not to overtighten.

7
Chair Assembly (continued)
Step 5: Finish attaching the chair legs (B and C) to the chair
seat (A) with washers (H) and short bolts (F). Use hex key (J)
to tighten bolts, being careful not to overtighten.
Step 6: Attach the support bar (E) to the front two legs with
washers (H) and short bolts (F). Use hex key (J) to tighten
bolts, being careful not to overtighten.

8
Chair Assembly (continued)
Step 7: Place the fully assembled chair upright onto flat surface
to level. Once leveled, fully tighten all of the bolts with hex key (J).
Attach all bolt caps (I) onto the bolts. The chair is now ready for use.
□Use mild soap and warm water to clean the frames.
□Rinse with clean water and dry thoroughly.
□Be sure to drain any water accumulated inside the frames. To
thoroughly drain frames, remove footcaps and tilt frames, if
necessary, to remove all water. Water allowed to accumulate inside
the frames and then exposed to sub-freezing temperatures can
cause damage to frame tubing. Such damage is not covered under
warranty.
□Any rust spots should be lightly sanded and treated with rust
inhibitor and followed with an application of touch-up paint (not
included).
□Use commercially available glass cleaners. Do not use abrasive
materials, cleansers or bleach products.
□Hand clean chair fabric with mild solution of soap and water. Rinse
thoroughly. Do not use bleach or solvents on fabric.
Care and Maintenance

9
90 DAY WARRANTY
This product is covered under a manufacturer’s 90 day warranty from date of
purchase against defects in materials and workmanship. This warranty does not
cover damage due to neglect, abuse or weather related damage. For full warranty
disclosure, email us at customerser[email protected], call toll free at 1-855-880-
7205 or send mail to: 1040 Boulevard SE Ste. B, Atlanta GA 30312
HOW TO FILE A CLAIM
If you are within your warranty you must have your receipt and pictures of your
information to send to ATLeisure at customerser[email protected], or send
by mail to 1040 Boulevard SE Ste. B, Atlanta GA 30312. This warranty gives you
specific legal rights, and you may also have other rights which vary from state to
state.
Warnings and Cautions
Warranty
DANGER: Keep children out of the assembly area during
assembly.
CAUTION: Do not stand on table or chairs.
CAUTION: Use chairs and table on flat ground only.

ATLeisure, LLC
1040 Boulevard SE, Suite B
Atlanta, Georgia 30312, USA
Customer Service Toll Free 1-855-880-7205
8am - 5pm Eastern Time, Monday through Friday
www.atleisure.com