Atlona AT-LINE-PRO2 User manual

AtlonA
CV/SV/PC/HD/HDMI 1080p
Scaler Box
AT-LINE-PRO2
User Manual

TABLE OF CONTENTS
1. Introduction .................................................. 1
2. Features .................................................. 1
3. Package Contents .................................................. 1
4. Operation Controls and Functions .................................................. 2
4.1 Front Panel .................................................. 2
4.2 Rear Panel .................................................. 3
4.3 OSD Operation .................................................. 4
4.4 Remote Control .................................................. 5
5. RS-232 Remote Control Protocol .................................................. 6
6. Specications .................................................. 9
6.1 General Specication .................................................. 9
6.2 Support Resolution .................................................. 9
7. Connection and Installation .................................................. 10
8. Safety Information .................................................. 11
9. Warranty .................................................. 12

INTRODUCTION
1
Atlona Scaler Box is designed to upscale digital/analog video signal from Composite, S-Video,
PC, Component (HD) and HDMI input sources, to digital HDMI output of wide-range HDTV and
PC resolutions, up to 1080p and WUXGA (1920 x 1200.) Besides video upscaling, the scaler
box also converts digital/analog audio signal to digital format, then output either through HDMI
combining with the video, or Coaxial S/PDIF separately. AT-LINE-PRO2 has a comprehensive
OSD menu that allows user to select a variety of output resolutions and adjust for best picture
quality.
• HDMI 1.2, HDCP 1.1 and DVI 1.0 compliant.
• Scales any PC (VGA ~ WUXGA) /HD (480i ~ 1080p) resolutions to/from another PC/HD
resolutions.
• Automatically detect the factory setting of the connected display and output the correspond-
ing resolution and refresh rate, when the NATIVE output is selected.
• Supports 50/60Hz frame rate conversion.
• Supports 3-D motion video adaptive, 3-D de-interlacing, and 3:2 / 2:2 pull-down detection
and recovery.
• Provides output picture adjustment on contrast, brightness, hue, saturation, sharpness,
RGB (color tone) level, and aspect ratio size.
• Supports high resolution input/output:
PC: VGA, SVGA, XGA, SXGA, UXGA, WXGA, WSXGA, WUXGA
HDTV: 480i, 576i, 480p, 576p, 720p, 1080i, and 1080p
• Supports digital and analog audio input and output
1. Atlona AT-LINE-PRO2 Scaler Box
2. D-Sub (15pin) Cable
3. 3XRCA Cable (Composite Video + L/R Audio)
4. Remote Controller
5. 5VDC Power Supply Adaptor
6. Operation Manual
FEATURES:
PACKAGE CONTENTS:

OPERATION CONTROLS and FUNCTION
2
Front Panel
1. POWER Button and LED Indicator: Press the button to turn ON/OFF the power of the unit.
The LED will illuminate when the power is turned on.
2. IR remote control sensor.
3. Input Selection Buttons and LED Indicators: Press each of the buttons (CV/SV/COMP/
PC/HDMI) to select the desired input source. The LED will illuminate when the corresponding
input is selected.
4. MENU Button: Press the MENU button to bring up OSD operation menu (see section “4.3
OSD Operation” for reference.)
5. +/- Buttons:
a. On the rst tier of OSD menu, use + and - buttons to move up/down the highlight item
for selection.
b. Once the desired option is selected, use + and - buttons to toggle between setting values.
6. ENTER Button: In OSD menu, use the ENTER button to conrm the selection

3
Rear Panel
1. HDMI OUT and CO-AX OUT: Connect the HDMI OUT port to the HDMI input port of your
display such as HDTV. Connect the CO-AX OUT port to the Coaxial (S/PDIF) input port of
your amplier for separate digital audio output.
2. AUX IN Input: When the video signal input through the HDMI IN port is from a DVI source
such as a PC,
use the AUX IN port to input the audio signal.
3. HDMI IN Input: Connect the HDMI IN port to the HDMI output port of your source equipment
such as DVD
player or Set-Top-Box. Or, use HDMI to DVI cable to connect to the DVI output of your PC.
4. RS-232: The port is for rmware update only.
5. PC IN for Video and Audio Input: Connect the PC IN D-Sub (15-pin) port to the D-Sub
output port of your PC. And, connect the PC IN 3.5mm phone jack to the audio output port of
your PC.
6. Y Pb/Cb Pr/Cr Video and L/R Audio Input: Connect the Y Pb/Cb Pr/Cr (Component) 3 RCA
input ports to the Component output port of your video source equipment such as DVD player
or Set-Top-Box. And, connect the L/R audio input ports to the audio output port of your audio
source equipment.
7. CO-AX Input: The CO-AX port provides the digital audio input support, and can be used to
combine with each video input signals from CV/SV/COMP/PC/HDMI ports. Once connected,
please use the Audio Source Selection in the OSD menu to select between Coaxial (S/PDIF)
or other audio source (see section “4.3 OSD Operation” for reference.)
8. Composite Video / S-Video and L/R Audio Input: Connect the Composite or S-Video input
port to the Composite or S-Video output port of your video source equipment such as DVD
player or Set-Top-Box. And, connect the L/R audio input ports to the audio output port of your
audio source equipment.
9. Power: Plug the 5VDC power supply into the unit and connect the adaptor to AC wall outlet
2

OSD Operation
1st Tier Option 2nd Tier Option Adjustment
VIDEO - PICTURE MODE USER / STANDARD / VIVID / MOVIE
- CONTRAST 0 ~ 100 of Contrast Level
- BRIGHTNESS 0 ~ 100 of Brightness Level
- HUE 0 ~ 100 of Hue Leve
- SATURATION 0 ~ 100 of Saturation Level
- SHARPNESS 0 ~ 100 of Sharpness Level
- SCALE OVERSCAN / UNDERSCAN / LETTERBOX
/PANSCAN / FULL
- NR LOW / MIDDLE / HIGH / OFF
- EXIT Back to the 1st Tier
COLOR - COLOR TONE USER / NORMAL / WARM / COOL
- RED 0 ~ 100 of Red Color Level
- GREEN 0 ~ 100 of Green Color Level
- BLUE 0 ~ 100 of Blue Color Level
- EXIT Back to the 1st Tier
OUTPUT -NATIVE / VGA / SVGA / XGA / SXGA/UXGA / 480i
/ 480p / 720p@60Hz/1080i@30Hz / 1080p@60Hz
/ 576i / 576p/720p@50Hz / 1080i@25Hz
/ 1080p@50Hz/WXGA / WSXGA / WUXGA
OSD - HPOSITION 0 ~ 100 of OSD Horizontal Position
- VPOSITION 0 ~ 100 of OSD Vertical Position
- TIMER 0 ~ 100 of OSD Show Time (sec.)
- TRANSP 0 ~ 100 of OSD Transparent Level
- EXIT Back to the 1st Tier
AUDIO - SOURCE HDMI / L/R / COAXIAL
- DELAY OFF / 40MS / 110MS / 150 MS
- SOUND ON / MUTE
- EXIT Back to the 1st Tier
INFORMATION -SOURCE (Input interface)
INPUT (Input Resolution)
OUTPUT (Output Resolution)
VERSION (Firmware Version)
EXIT -Close the OSD Menu
4

Remote Control
1. POWER:
Press the button once to power on the AT-LINE-PRO2.
Press again to enter standby mode.
2. INPUT:
Press the button repeatedly to toggle through various
input sources.
3. HD Input:
Press the button to directly select component input.
4. PC Input:
Press the button to directly select PC input.
5. HDMI/DVI Input:
Press the button to directly select DVI (or HDMI) input.
6. Output Resolution:
Press any one of the button to directly select output
resolution. For other output resolutions that are not
covered by these buttons please enter OSD Menu to
select them.
7. MENU:
Press the button to bring up OSD main menu page.
8. Exit:
Press the button to exit from a sub menu or main menu.
9. Up/Down/Left/Right:
Press the Up/Down button to move the highlight bar
to your desired parameter during the OSD operation.
Press the Left/Right button to increase/decrease
the setting value of a selected parameter.
10. OK (Enter):
Press the button to conrm your selection.
11. Reset:
Press the button to reset the unit’s rmware setting to the factory default value.
12. Auto Adjust:
Press the button to optimize the position of the picture (picture centering) on the screen.
4 5

6
RS-232 REMOTE CONTROL PROTOCOL
The connection between AT-LINE-PRO2 and remote controller with RS-232 modem cable.
Pins denition of modem cable:
AT-LINE-PRO2 Remote Controlle
PIN Denition PIN Denition
1NC 1NC
2 TxD 2 RxD
3 RxD g3 TxD
4NC 4NC
5GND f5GND
6NC 6NC
7NC 7NC
8NC 8NC
9 NC 9 NC
RS-232 transmission format:
Baud Rate: 19200 bps
Data Bit: 8 bits
Parity: None
Stop Bit: 1 bit

6 7
(A) Set Command:
Command Code Response Description
S POWER 0 >POWER OFF POWER OFF
S POWER 1 >POWER ON POWER ON
S SOURCE 0 >SOURCE CV CV INPUT
S SOURCE 1 > SOURCE SV SV INPUT
S SOURCE 2 > SOURCE COMP COMP INPUT
S SOURCE 3 > SOURCE PC PC INPUT
S SOURCE 4 > SOURCE HDMI HDMI INPUT
S OUTPUT 0 > OUTPUT NATIVE NATIVE RESOLUTION OUTPUT
S OUTPUT 1 > OUTPUT VGA VGA RESOLUTION OUTPUT
S OUTPUT 2 > OUTPUT SVGA SVGA RESOLUTION OUTPUT
S OUTPUT 3 > OUTPUT XGA XGA RESOLUTION OUTPUT
S OUTPUT 4 > OUTPUT SXGA SXGA RESOLUTION OUTPUT
S OUTPUT 5 > OUTPUT UXGA UXGA RESOLUTION OUTPUT
S OUTPUT 6 > OUTPUT 480i 480i RESOLUTION OUTPUT
S OUTPUT 7 > OUTPUT 480p 480p RESOLUTION OUTPUT
S OUTPUT 8 > OUTPUT 720p 720p 60Hz RESOLUTION OUTPUT
S OUTPUT 9 > OUTPUT 1080i 1080i 60Hz RESOLUTION OUTPUT
S OUTPUT 10 > OUTPUT 1080p 1080p 60Hz RESOLUTION OUTPUT
S OUTPUT 11 > OUTPUT 576i 576i 60Hz RESOLUTION OUTPUT
S OUTPUT 12 > OUTPUT 576p 576p 60Hz RESOLUTION OUTPUT
S OUTPUT 13 > OUTPUT 720p 720p 50Hz RESOLUTION OUTPUT
S OUTPUT 14 > OUTPUT 1080i50 1080i 50Hz RESOLUTION OUTPUT
S OUTPUT 15 > OUTPUT 1080p50 1080p 50Hz RESOLUTION OUTPUT
S OUTPUT 16 > OUTPUT WXGA WXGA RESOLUTION OUTPUT
S OUTPUT 17 > OUTPUT WSXGA WSXGA RESOLUTION OUTPUT
S OUTPUT 18 > OUTPUT WUXGA WUXGA RESOLUTION OUTPUT
S SIZE 0 > SIZE FULL SCALER FULL OUTPUT
S SIZE 1 > SIZE OVERSCAN SCALER OVERSCAN OUTPUT
S SIZE 2 > SIZE UNDERSCAN SCALER UNDERSCAN OUTPUT
S SIZE 3 > SIZE LETTERBOX SCALER LETTERBOX OUTPUT
S SIZE 4 > SIZE PANSCAN SCALER PANSCAN OUTPUT
S PICTUREMODE 0~3 > PICTUREMODE STANDARD~USER 0:STANDARD; 1:MOVIE; 2:VIVID; 3:USER; PICTUREMODE
OUTPUT
S CONTRAST 0~100 > CONTRAST 0~100 CONTRAST 0~100 ADJUST [Default:50]
S BRIGHTNESS 0~100 > BRIGHTNESS 0~100 BRIGHTNESS 0~100 ADJUST [Default:45]
S HUE 0~100 > HUE 0~100 HUE 0~100 ADJUST [Default:50]
S SATURATION 0~100 > SATURATION 0~100 SATURATION 0~100 ADJUST [Default:60]
S SHARPNESS 0~100 > SHARPNESS 0~100 SHARPNESS 0~100 ADJUST [Default:32]
S NR 0~100 >NR OFF~HIGH 0:OFF; 1:LOW; 2:MIDDLE; 3:HIGH. NR CONTROL
S PCHPOSITION 0~100 > PCHPOSITION 0~100 H POSITION 0~100 ADJUST
S PCVPOSITION 0~100 > PCVPOSITION 0~100 V POSITION 0~100 ADJUST
S PCCLOCK 0~100 > PCCLOCK 0~100 PC MODE CLOCK 0~100 ADJUST
S PCPHASE 0~63 > PCPHASE 0~63 PC MODE PHASE 0~100 ADJUST

8
S COLORTEMP 0~3 >COLORTEMP NORMAL~USER 0:NORMAL; 1:WARM; 2:COOL; 3:USER. COLOR TEMP SET-
TINGS
S RED 0~100 > RED 0~100 COLOR TEMP ”RED” ADJUST [Default:47]
S GREEN 0~100 > GREEN 0~100 COLOR TEMP “GREEN“ ADJUST [Default:47]
S BLUE 0~100 > BLUE 0~100 COLOR TEMP “BLUE“ ADJUST [Default:47]
S OSDHPOSITION 0~100 > OSDHPOSITION 0~100 OSD H POSITION 0~100 ADJUST [Default:50]
S OSDVPOSITION 0~100 > OSDVPOSITION 0~100 OSD V POSITION 0~100 ADJUST [Default:50]
S OSDTIMEOUT 0~100 > OSDTIMEOUT 0~100 OSD TIMEOUT 0~100 SETTING [Default:10]
S OSDBACKGROUND 0~8 > OSDBACKGROUND 0~8 OSD BACKGROUND 0~8 ADJUST [Default:5]
S AUDIOMUTE 0~1 > AUDIOMUTE OFF~ON 0:OFF; 1:ON. AUDIO MUTE CONTROL
S AUDIODELAY 0~3 > AUDIODELAY OFF~150ms 0:OFF; 1:40ms; 2:110ms; 3:150ms. AUDIO DELAY SETTING
S RESET 1 > RESET ON RESET ACTION
(B) Status Commend :
Command Code Response Description
R POWER >POWER ON SHOW POWER STATUS
R SOURCE >SOURCE CV~HDMI SHOW SOURCE STATUS
R OUTPUT >OUTPUT NATIVE~WUXGA SHOW OUTPUT STATUS
R SIZE >SIZE FULL~PANSCAN SHOW SIZE STATUS
R PICTUREMODE > PICTUREMODE STANDARD~USER SHOW PICTURE MODE STATUS
R CONTRAST > CONTRAST 0~100 SHOW CONTRAST STATUS
R BRIGHTNESS > BRIGHTNESS 0~100 SHOW BRIGHTNESS STATUS
R HUE > HUE 0~100 SHOW HUE STATUS
R SATURATION > SATURATION 0~100 SHOW SATURATION STATUS
R SHARPNESS > SHARPNESS 0~100 SHOW SHARPNESS STATUS
R NR > NR OFF~HIGH SHOW NR STATUS
R PCHPOSITION > PCHPOSITION 0~100 SHOW PC H-POSITION STATUS
R PCVPOSITION > PCVPOSITION 0~100 SHOW PC V-POSITION STATUS
R PCCLOCK > PCCLOCK 0~100 SHOW PC CLOCK STATUS
R PCPHASE > PCPHASE 0~63 SHOW PC PHASE STATUS
R COLORTEMP > COLORTEMP NORMAL~USER SHOW COLOR TEMP STATUS
R RED > RED 0~100 SHOW COLOR TEMP RED STATUS
R GREEN > GREEN 0~100 SHOW COLOR TEMP GREEN STATUS
R BLUE > BLUE 0~100 SHOW COLOR TEMP BLUE STATUS
R OSDHPOSITION > OSDHPOSITION 0~100 SHOW OSD H-POSITION STATUS
R OSDVPOSITION > OSDVPOSITION 0~100 SHOW OSD V-POSITION STATUS
R OSDTIMEOUT > OSDTIMEOUT 0~100 SHOW OSD TIMEOUT STATUS
R OSDBACKGROUND > OSDBACKGROUND 0~8 SHOW OSD BACKGROUND STATUS
R AUDIOMUTE > AUDIOMUTE OFF~ON SHOW AUDIO MUTE STATUS
R AUDIODELAY > AUDIODELAY OFF~150ms SHOW AUDIO DELAY STATUS